switchport nonegociate missing on the pe? 2010/2/17, Ioan Branet <[email protected]>: > Hello, > > I used also vlan-tagging but with same result: > > show configuration interfaces xe-3/1/0 > description "** Link To PE1 **"; > vlan-tagging; > link-mode full-duplex; > gigether-options { > no-auto-negotiation; > } > unit 999 { > bandwidth 10g; > vlan-id 999; > family inet { > accounting { > source-class-usage { > input; > } > } > no-redirects; > sampling { > input; > } > address 150.1.1.2/30 { > primary; > preferred; > } > } > } > > #ping 150.1.1.2 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 150.1.1.2, timeout is 2 seconds: > ..... > Success rate is 0 percent (0/5) > > On Wed, Feb 17, 2010 at 7:06 PM, Manu Chao <[email protected]> wrote: > >> Hello, >> >> It is just a config problem on your J CE1: You needn't >> flexible-vlan-tagging (nor flexible-ethernet-services encapsulation) >> >> R/ >> Manu >> On Wed, Feb 17, 2010 at 5:01 PM, Ioan Branet <[email protected]>wrote: >> >>> Hello, >>> >>> I tried with Cisco 7600 as CE instead of Juniper and it works, I have to >>> find out what is wrong there. >>> >>> Thank you for your help, >>> Regards, >>> John >>> >>> ---------- Forwarded message ---------- >>> From: Ioan Branet <[email protected]> >>> Date: Wed, Feb 17, 2010 at 11:44 AM >>> Subject: Re: [c-nsp] EOMPLS between 10G subinterface and GE subinterface >>> between two 7600 >>> To: Tassos Chatzithomaoglou <[email protected]> >>> Cc: [email protected] >>> >>> >>> Hello, >>> >>> Maybe there is a bug with SRB IOS. >>> I still have VC up on both ends but I cant ping between CE1 and CE2. >>> >>> On CE1 (Juniper side) I learn arp address of remote CE2 device and >>> receive >>> arp request and send arp reply: >>> >>> >>> show arp no-resolve | match xe-3/1/0 >>> 00:16:9c:6d:42:80 150.1.1.1 xe-3/1/0.999 none >>> >>> >>> Juniper PCAP Flags [Ext, In], PCAP Extension(s) total length 22 >>> Device Media Type Extension TLV #3, length 1, value: Ethernet >>> (1) >>> Logical Interface Encapsulation Extension TLV #6, length 1, >>> value: >>> Ethernet (14) >>> Device Interface Index Extension TLV #1, length 2, value: 193 >>> Logical Interface Index Extension TLV #4, length 4, value: 126 >>> Logical Unit Number Extension TLV #5, length 4, value: 32767 >>> -----original packet----- >>> 0:16:9c:6d:42:80 > Broadcast, ethertype 802.1Q (0x8100), length >>> 64: >>> vlan 999, p 0, ethertype ARP, arp who-has 150.1.1.2 tell 150.1.1.1 >>> 11:34:01.878596 Out >>> Juniper PCAP Flags [Ext], PCAP Extension(s) total length 22 >>> Device Media Type Extension TLV #3, length 1, value: Ethernet >>> (1) >>> Logical Interface Encapsulation Extension TLV #6, length 1, >>> value: >>> Ethernet (14) >>> Device Interface Index Extension TLV #1, length 2, value: 193 >>> Logical Interface Index Extension TLV #4, length 4, value: 126 >>> Logical Unit Number Extension TLV #5, length 4, value: 32767 >>> -----original packet----- >>> 0:21:59:a7:c4:30 > 0:16:9c:6d:42:80, ethertype 802.1Q (0x8100), >>> length 46: vlan 999, p 0, ethertype ARP, arp reply 150.1.1.2 is-at >>> 0:21:59:a7:c4:30. >>> >>> The issue is that I can't upgrade to SRD IOS. >>> >>> thank you, >>> John >>> >>> >>> >>> On Wed, Feb 17, 2010 at 11:05 AM, Tassos Chatzithomaoglou < >>> [email protected]> wrote: >>> >>> > I'm running EoMPLS between 10GE subif and 1GE subif without any >>> > problem. >>> > >>> > 7600-a>sh mpls l2 vc 3601 >>> > >>> > Local intf Local circuit Dest address VC ID >>> Status >>> > ------------- -------------------------- --------------- ---------- >>> > ---------- >>> > Gi4/20.3601 Eth VLAN 3601 x.x.x.x 3601 UP >>> > >>> > >>> > 7600-b>sh mpls l2 vc 3601 >>> > >>> > Local intf Local circuit Dest address VC ID >>> Status >>> > ------------- -------------------------- --------------- ---------- >>> > ---------- >>> > Te3/2.3601 Eth VLAN 3601 x.x.x.x 3601 UP >>> > >>> > >>> > Both 7600s are running SRD3. >>> > >>> > -- >>> > Tassos >>> > >>> > Ioan Branet wrote on 17/02/2010 10:49: >>> > >>> >> Hello, >>> >> >>> >> We run EOMPLS on port and vlan mode on GE interfaces but we did not >>> >> run >>> >> EOMPLS Vlan mode between 10G and 1G subinterfaces until now. >>> >> >>> >> Any feedback is appreciated. >>> >> Thank you, >>> >> John >>> >> >>> >> On Wed, Feb 17, 2010 at 10:43 AM, Mikael Abrahamsson <[email protected] >>> >> >wrote: >>> >> >>> >> >>> >> >>> >>> On Wed, 17 Feb 2010, Ioan Branet wrote: >>> >>> >>> >>> You should answer to the list, answering just to me doesn't make much >>> >>> sense. >>> >>> >>> >>> SRB4 is buggy, stop running it. Try latest SRB (SRB6 or 7, I don't >>> >>> remember), or go SRD3 or later. >>> >>> >>> >>> >>> >>> Hello, >>> >>> >>> >>> >>> >>>> We are running on both PEs the following: >>> >>>> sh ver | i IOS >>> >>>> Cisco IOS Software, c7600s72033_rp Software >>> >>>> (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE >>> >>>> SOFTWARE >>> >>>> (fc3) >>> >>>> >>> >>>> 10G card on PE1 is: >>> >>>> show module 7 >>> >>>> Mod Ports Card Type Model >>> >>>> Serial >>> >>>> No. >>> >>>> --- ----- -------------------------------------- ------------------ >>> >>>> ----------- >>> >>>> 7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE >>> >>>> SAL1337YN4W >>> >>>> >>> >>>> and 1G on PE2 is: >>> >>>> >>> >>>> >>> >>>> ro-sv01a-rd2#show module 2 >>> >>>> Mod Ports Card Type Model >>> >>>> Serial >>> >>>> No. >>> >>>> --- ----- -------------------------------------- ------------------ >>> >>>> ----------- >>> >>>> 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP >>> >>>> SAL1005CBXG >>> >>>> >>> >>>> Mod MAC addresses Hw Fw Sw >>> >>>> Status >>> >>>> --- ---------------------------------- ------ ------------ >>> ------------ >>> >>>> ------- >>> >>>> 2 0016.c8c4.fc10 to 0016.c8c4.fc27 2.3 12.2(14r)S5 >>> 12.2(33)SRB4 >>> >>>> Ok >>> >>>> >>> >>>> Mod Sub-Module Model Serial Hw >>> >>>> Status >>> >>>> ---- --------------------------- ------------------ ----------- >>> ------- >>> >>>> ------- >>> >>>> 2 Centralized Forwarding Card WS-F6700-CFC SAL1014J60S 2.0 >>> >>>> Ok >>> >>>> >>> >>>> Mod Online Diag Status >>> >>>> ---- ------------------- >>> >>>> 2 Pass >>> >>>> >>> >>>> Thank you, >>> >>>> John >>> >>>> >>> >>>> On Wed, Feb 17, 2010 at 10:27 AM, Mikael Abrahamsson < >>> [email protected] >>> >>>> >>> >>>> >>> >>>>> wrote: >>> >>>>> >>> >>>>> >>> >>>> On Wed, 17 Feb 2010, Ioan Branet wrote: >>> >>>> >>> >>>> >>> >>>>> GE interface between two 7600 as PE. >>> >>>>> >>> >>>>> >>> >>>>> >>> >>>>>> >>> >>>>>> >>> >>>>> You forgot to include what software you're running. >>> >>>>> >>> >>>>> -- >>> >>>>> Mikael Abrahamsson email: [email protected] >>> >>>>> >>> >>>>> >>> >>>>> >>> >>>>> >>> >>>> -- >>> >>> Mikael Abrahamsson email: [email protected] >>> >>> >>> >>> >>> >>> >>> >> _______________________________________________ >>> >> cisco-nsp mailing list [email protected] >>> >> https://puck.nether.net/mailman/listinfo/cisco-nsp >>> >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>> >> >>> >> >>> >> >>> > >>> > _______________________________________________ >>> > cisco-nsp mailing list [email protected] >>> > https://puck.nether.net/mailman/listinfo/cisco-nsp >>> > archive at http://puck.nether.net/pipermail/cisco-nsp/ >>> > >>> _______________________________________________ >>> cisco-nsp mailing list [email protected] >>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>> >> >> > > > -- > Ioan Branet > CCIE #23474 R&S >
-- Envoyé avec mon mobile _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
