Hello, I tried with Cisco 7600 as CE instead of Juniper and it works, I have to find out what is wrong there.
Thank you for your help, Regards, John ---------- Forwarded message ---------- From: Ioan Branet <[email protected]> Date: Wed, Feb 17, 2010 at 11:44 AM Subject: Re: [c-nsp] EOMPLS between 10G subinterface and GE subinterface between two 7600 To: Tassos Chatzithomaoglou <[email protected]> Cc: [email protected] Hello, Maybe there is a bug with SRB IOS. I still have VC up on both ends but I cant ping between CE1 and CE2. On CE1 (Juniper side) I learn arp address of remote CE2 device and receive arp request and send arp reply: show arp no-resolve | match xe-3/1/0 00:16:9c:6d:42:80 150.1.1.1 xe-3/1/0.999 none Juniper PCAP Flags [Ext, In], PCAP Extension(s) total length 22 Device Media Type Extension TLV #3, length 1, value: Ethernet (1) Logical Interface Encapsulation Extension TLV #6, length 1, value: Ethernet (14) Device Interface Index Extension TLV #1, length 2, value: 193 Logical Interface Index Extension TLV #4, length 4, value: 126 Logical Unit Number Extension TLV #5, length 4, value: 32767 -----original packet----- 0:16:9c:6d:42:80 > Broadcast, ethertype 802.1Q (0x8100), length 64: vlan 999, p 0, ethertype ARP, arp who-has 150.1.1.2 tell 150.1.1.1 11:34:01.878596 Out Juniper PCAP Flags [Ext], PCAP Extension(s) total length 22 Device Media Type Extension TLV #3, length 1, value: Ethernet (1) Logical Interface Encapsulation Extension TLV #6, length 1, value: Ethernet (14) Device Interface Index Extension TLV #1, length 2, value: 193 Logical Interface Index Extension TLV #4, length 4, value: 126 Logical Unit Number Extension TLV #5, length 4, value: 32767 -----original packet----- 0:21:59:a7:c4:30 > 0:16:9c:6d:42:80, ethertype 802.1Q (0x8100), length 46: vlan 999, p 0, ethertype ARP, arp reply 150.1.1.2 is-at 0:21:59:a7:c4:30. The issue is that I can't upgrade to SRD IOS. thank you, John On Wed, Feb 17, 2010 at 11:05 AM, Tassos Chatzithomaoglou < [email protected]> wrote: > I'm running EoMPLS between 10GE subif and 1GE subif without any problem. > > 7600-a>sh mpls l2 vc 3601 > > Local intf Local circuit Dest address VC ID Status > ------------- -------------------------- --------------- ---------- > ---------- > Gi4/20.3601 Eth VLAN 3601 x.x.x.x 3601 UP > > > 7600-b>sh mpls l2 vc 3601 > > Local intf Local circuit Dest address VC ID Status > ------------- -------------------------- --------------- ---------- > ---------- > Te3/2.3601 Eth VLAN 3601 x.x.x.x 3601 UP > > > Both 7600s are running SRD3. > > -- > Tassos > > Ioan Branet wrote on 17/02/2010 10:49: > >> Hello, >> >> We run EOMPLS on port and vlan mode on GE interfaces but we did not run >> EOMPLS Vlan mode between 10G and 1G subinterfaces until now. >> >> Any feedback is appreciated. >> Thank you, >> John >> >> On Wed, Feb 17, 2010 at 10:43 AM, Mikael Abrahamsson <[email protected] >> >wrote: >> >> >> >>> On Wed, 17 Feb 2010, Ioan Branet wrote: >>> >>> You should answer to the list, answering just to me doesn't make much >>> sense. >>> >>> SRB4 is buggy, stop running it. Try latest SRB (SRB6 or 7, I don't >>> remember), or go SRD3 or later. >>> >>> >>> Hello, >>> >>> >>>> We are running on both PEs the following: >>>> sh ver | i IOS >>>> Cisco IOS Software, c7600s72033_rp Software >>>> (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB4, RELEASE >>>> SOFTWARE >>>> (fc3) >>>> >>>> 10G card on PE1 is: >>>> show module 7 >>>> Mod Ports Card Type Model >>>> Serial >>>> No. >>>> --- ----- -------------------------------------- ------------------ >>>> ----------- >>>> 7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE >>>> SAL1337YN4W >>>> >>>> and 1G on PE2 is: >>>> >>>> >>>> ro-sv01a-rd2#show module 2 >>>> Mod Ports Card Type Model >>>> Serial >>>> No. >>>> --- ----- -------------------------------------- ------------------ >>>> ----------- >>>> 2 24 CEF720 24 port 1000mb SFP WS-X6724-SFP >>>> SAL1005CBXG >>>> >>>> Mod MAC addresses Hw Fw Sw >>>> Status >>>> --- ---------------------------------- ------ ------------ ------------ >>>> ------- >>>> 2 0016.c8c4.fc10 to 0016.c8c4.fc27 2.3 12.2(14r)S5 12.2(33)SRB4 >>>> Ok >>>> >>>> Mod Sub-Module Model Serial Hw >>>> Status >>>> ---- --------------------------- ------------------ ----------- ------- >>>> ------- >>>> 2 Centralized Forwarding Card WS-F6700-CFC SAL1014J60S 2.0 >>>> Ok >>>> >>>> Mod Online Diag Status >>>> ---- ------------------- >>>> 2 Pass >>>> >>>> Thank you, >>>> John >>>> >>>> On Wed, Feb 17, 2010 at 10:27 AM, Mikael Abrahamsson <[email protected] >>>> >>>> >>>>> wrote: >>>>> >>>>> >>>> On Wed, 17 Feb 2010, Ioan Branet wrote: >>>> >>>> >>>>> GE interface between two 7600 as PE. >>>>> >>>>> >>>>> >>>>>> >>>>>> >>>>> You forgot to include what software you're running. >>>>> >>>>> -- >>>>> Mikael Abrahamsson email: [email protected] >>>>> >>>>> >>>>> >>>>> >>>> -- >>> Mikael Abrahamsson email: [email protected] >>> >>> >>> >> _______________________________________________ >> cisco-nsp mailing list [email protected] >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> >> >> > > _______________________________________________ > cisco-nsp mailing list [email protected] > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
