Hello, It's a possibility I have considered as it is a refurb chassis.
Any other ideas ? Thanks. Y. 2010/3/8 Manu Chao <linux.ya...@gmail.com> > hardware issue: connector? > On Mon, Mar 8, 2010 at 4:42 PM, Youssef Bengelloun-Zahr <yous...@720.fr>wrote: > >> Hello community, >> >> I received a 7204VXR chassis with a I/O controler (no FE ports on it) et >> plugged in it an old NPE-400 plus 2 PA-FE. >> >> PA-FE 1 in in slot 1. >> >> PA-FE 2 is in slot 2. >> >> Upgraded my bootloader with c7200-boot-mz.120-22.S.bin and my version of >> IOS >> is c7200-adventerprisek9-mz.122-33.SRD.bin. >> >> Here is my problem : >> >> When PA-FE1 is in slot1, the router loops during boot and the following >> appears : >> >> *Mar 8 05:20:09.459: %SYS-5-RELOAD: Reload requested by console. Reload >> Reason: Reload command. >> System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1) >> TAC Support: http://www.cisco.com/tac >> Copyright (c) 2002 by cisco Systems, Inc. >> C7200 platform with 524288 Kbytes of main memory >> >> >> Self decompressing the image : >> >> ###########################################################################################################################################################################################################] >> >> %SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be correctly >> understood >> %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? >> %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? >> %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? >> %SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader. >> Self decompressing the image : >> >> ###########################################################################################################################################################################################################] >> >> System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1) >> TAC Support: http://www.cisco.com/tac >> Copyright (c) 2002 by cisco Systems, Inc. >> >> *ROM: Rebooted by watchdog hard reset >> *C7200 platform with 524288 Kbytes of main memory >> >> >> When I remove the PA-FE from slot 1 or insert it in another slot (2,3 or >> 4), >> everything works like a charm. Moreover, swapping with another PA-FE in >> slot1 causes the same problem !?! >> >> Here is a sh controller of the PA-FE in question (but inserted in slot 3) >> : >> >> Interface FastEthernet3/0 >> Hardware is DEC21140 >> dec21140_ds=0x65948454, registers=0x3D800000, ib=0xE179D40 >> rx ring entries=128, tx ring entries=256, af setup failed=0 >> rxring=0x7E179E40, rxr shadow=0x65948A38, rx_head=0, rx_tail=0 >> txring=0x7E17A680, txr shadow=0x65948C6C, tx_head=2, tx_tail=2, >> tx_count=0 >> PHY link up >> CSR0=0xFFFA9082, CSR3=0xE179E40, CSR4=0xE17A680, CSR5=0xFC000000 >> CSR6=0xE0000000, CSR7=0xFFFE0000, CSR8=0xFFFE0000, CSR9=0xFFFDD7FF >> CSR11=0xFFFE0000, CSR12=0xFFFFFF09, CSR15=0xFFFFFEC8 >> TX state: stopped >> RX state: stopped - RESET or STOP RECEIVE command >> Far End Fault Indication (For FX Interface): OFF >> DEC21140 PCI registers: >> bus_no=6, device_no=0 >> CFID=0x00091011, CFCS=0x02800006, CFRV=0x02000012, CFLT=0x0000FF00 >> CBIO=0xDFEFFF81, CBMA=0x49000000, CFIT=0x000001D1, CFDA=0x0000EF00 >> MII registers: >> Register 0x00: 0400 784B 2000 5C01 0081 0000 0000 0000 >> Register 0x08: 0000 0000 0000 0000 0000 0000 0000 0000 >> Register 0x10: 0000 0000 0000 0000 0000 0001 8060 >> Register 0x18: 8020 0800 0000 3800 A3B9 >> Software MAC address filter(hash:length/addr/mask/hits): >> need_af_check = 0 >> 0x00: 0 ffff.ffff.ffff 0000.0000.0000 0 >> 0x10: 0 0009.443e.8854 0000.0000.0000 0 >> throttled=0, enabled=0, disabled=0 >> rx_fifo_overflow=0, rx_no_enp=0, rx_state=0 >> tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=1 >> tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0 >> tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0 >> rx_pak_len_err = 0, filtered_pak_cnt = 0 >> tx_limited=0(256) >> HW addr filter: 0xE18E700, ISL Disabled >> Entry= 0: Addr=FFFF.FFFF.FFFF >> Entry= 1: Addr=FFFF.FFFF.FFFF >> Entry= 2: Addr=FFFF.FFFF.FFFF >> Entry= 3: Addr=FFFF.FFFF.FFFF >> Entry= 4: Addr=FFFF.FFFF.FFFF >> Entry= 5: Addr=FFFF.FFFF.FFFF >> Entry= 6: Addr=FFFF.FFFF.FFFF >> Entry= 7: Addr=FFFF.FFFF.FFFF >> Entry= 8: Addr=FFFF.FFFF.FFFF >> Entry= 9: Addr=FFFF.FFFF.FFFF >> Entry=10: Addr=FFFF.FFFF.FFFF >> Entry=11: Addr=FFFF.FFFF.FFFF >> Entry=12: Addr=FFFF.FFFF.FFFF >> Entry=13: Addr=FFFF.FFFF.FFFF >> Entry=14: Addr=FFFF.FFFF.FFFF >> Entry=15: Addr=0009.443E.8854 >> >> I have been googling around but nothing very concluant so far. >> >> Any clues ? >> >> Thanks. >> >> Best regards. >> >> Cheers, >> >> -- >> Youssef BENGELLOUN-ZAHR ……………………………………………… >> Ingénieur Réseaux et Télécoms >> >> >> Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 >> Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE >> Tel +33 (0) 825 000 720 >> Tel. direct +33 (0) 1 77 35 59 14 >> Tel. portable +33 (0) 6 22 42 63 80 >> Email y...@720.fr >> ……………………………………………………………………………….....www.720.fr >> _______________________________________________ >> cisco-nsp mailing list cisco-nsp@puck.nether.net >> https://puck.nether.net/mailman/listinfo/cisco-nsp >> archive at http://puck.nether.net/pipermail/cisco-nsp/ >> > > -- Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et Télécoms Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE Tel +33 (0) 825 000 720 Tel. direct +33 (0) 1 77 35 59 14 Tel. portable +33 (0) 6 22 42 63 80 Email y...@720.fr ……………………………………………………………………………….....www.720.fr _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/