Hello all, I have inserted the PA-FE in the chassis after the router has booted, here is an output of a show diag :
Slot 1: Fast-ethernet (TX-ISL) Port adapter, 1 port Port adapter is analyzed Port adapter insertion time 00:00:04 ago EEPROM contents at hardware discovery: Hardware revision 1.0 Board revision A0 Serial number 7808144 Part number 73-1688-04 FRU Part Number: PA-FE-TX Test history 0x0 RMA number 00-00-00 EEPROM format version 1 EEPROM contents (hex): 0x20: 01 11 01 00 00 77 24 90 49 06 98 04 00 00 00 00 0x30: 50 00 00 00 98 02 20 00 FF FF FF FF FF FF FF FF The PA-FE is well recognized. I have also inspected the backplane on slot 1, It's all good (no bend pins). Then, I reboot the router with the PA-FE still in slot 1 and I get the same loop again and again : Router#reload Proceed with reload? [confirm] *Mar 14 23:29:29.271: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command. System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. C7200 platform with 524288 Kbytes of main memory Self decompressing the image : ###########################################################################################################################################################################################################] %SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be correctly understood %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? %SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader. Self decompressing the image : ###########################################################################################################################################################################################################] System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. ROM: Rebooted by watchdog hard reset C7200 platform with 524288 Kbytes of main memory Self decompressing the image : ###########################################################################################################################################################################################################] %SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be correctly understood %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? %DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem? %SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader. Self decompressing the image : ###########################################################################################################################################################################################################] System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/tac Copyright (c) 2002 by cisco Systems, Inc. ROM: Rebooted by watchdog hard reset C7200 platform with 524288 Kbytes of main memory Self decompressing the image : ###########################################################################################################################################################################################################] %SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not be correctly understood ..... As soon as I remove the PA-FE from slot 1, router boots normaly !!! Any clues !?! Thanks. Y. 2010/3/8 Youssef Bengelloun-Zahr <yous...@720.fr> > The PA-FE is Wellington recognized if I recall correctly... > > I'll try it again and see just to be sure. > > Y. > > > > Le 8 mars 2010 à 18:39, "Buhrmaster, Gary" <g...@slac.stanford.edu> a écrit > : > > > When PA-FE1 is in slot1, the router loops during boot and the following >>> appears : >>> >> >> Have you tried booting, and then plugging a PA-FE into >> slot 1? The diagnostics *might* be better when running >> the full IOS. >> >> >> -- Youssef BENGELLOUN-ZAHR ……………………………………………… Ingénieur Réseaux et Télécoms Technopole de l'Aube en Champagne - BP 601 - 10901 TROYES Cedex 9 Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE Tel +33 (0) 825 000 720 Tel. direct +33 (0) 1 77 35 59 14 Tel. portable +33 (0) 6 22 42 63 80 Email y...@720.fr ……………………………………………………………………………….....www.720.fr _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/