Re: [c-nsp] 7204VXR rebooted by watchdog hard reset with PA-FE in slot 1

Youssef Bengelloun-Zahr Mon, 08 Mar 2010 10:11:37 -0800

Hello,

As I sais in my first post, I had to upgrade the bootloader because itwas too old but the slot was perfectly working then. This is why it'sbugging me so much...


I'll check the backplane for any Bent pins but still...


Y.



Le 8 mars 2010 à 18:29, Eninja <[email protected]> a écrit :

Youssef,
You've answered your own question- you have a bad slot 1. Check tosee if there are any bent pins in it/make sure the PAs actually seatproperly in it. ITMT, avoid using slot 1 to prevent further reloads.
/eninja
"When I remove the PA-FE from slot 1 or insert it in another slot(2,3 or4), everything works like a charm. Moreover, swapping withanother PA-FE in slot1 causes the same problem"
On Mar 8, 2010, at 5:33 PM, Youssef Bengelloun-Zahr <[email protected]>wrote:
Hello,

It's a possibility I have considered as it is a refurb chassis.

Any other ideas ?

Thanks.

Y.



2010/3/8 Manu Chao <[email protected]>
hardware issue: connector?
On Mon, Mar 8, 2010 at 4:42 PM, Youssef Bengelloun-Zahr <[email protected]>wrote:
Hello community,
I received a 7204VXR chassis with a I/O controler (no FE ports onit) et
plugged in it an old NPE-400 plus 2 PA-FE.

PA-FE 1 in in slot 1.

PA-FE 2 is in slot 2.
Upgraded my bootloader with c7200-boot-mz.120-22.S.bin and myversion of
IOS
is c7200-adventerprisek9-mz.122-33.SRD.bin.

Here is my problem :
When PA-FE1 is in slot1, the router loops during boot and thefollowing
appears :
*Mar 8 05:20:09.459: %SYS-5-RELOAD: Reload requested by console.Reload
Reason: Reload command.
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C7200 platform with 524288 Kbytes of main memory


Self decompressing the image :
###########################################################################################################################################################################################################]
%SYS-4-CONFIG_NEWER: Configuration from version 12.2 may not becorrectly
understood
%DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem?
%DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem?
%DEC21140-5-NOCARR: FastEthernet1/0 cable/connector problem?
%SYS-6-BOOT_MESSAGES: Messages above this line are from the bootloader.
Self decompressing the image :
###########################################################################################################################################################################################################]
System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.

*ROM: Rebooted by watchdog hard reset
*C7200 platform with 524288 Kbytes of main memory
When I remove the PA-FE from slot 1 or insert it in another slot(2,3 or
4),
everything works like a charm. Moreover, swapping with another PA-FE in
slot1 causes the same problem !?!
Here is a sh controller of the PA-FE in question (but inserted inslot 3)
:

Interface FastEthernet3/0
Hardware is DEC21140
dec21140_ds=0x65948454, registers=0x3D800000, ib=0xE179D40
rx ring entries=128, tx ring entries=256, af setup failed=0
rxring=0x7E179E40, rxr shadow=0x65948A38, rx_head=0, rx_tail=0
txring=0x7E17A680, txr shadow=0x65948C6C, tx_head=2, tx_tail=2,
tx_count=0
PHY link up
CSR0=0xFFFA9082, CSR3=0xE179E40, CSR4=0xE17A680, CSR5=0xFC000000
CSR6=0xE0000000, CSR7=0xFFFE0000, CSR8=0xFFFE0000, CSR9=0xFFFDD7FF
CSR11=0xFFFE0000, CSR12=0xFFFFFF09, CSR15=0xFFFFFEC8
TX state: stopped
RX state: stopped - RESET or STOP RECEIVE command
Far End Fault Indication (For FX Interface): OFF
DEC21140 PCI registers:
bus_no=6, device_no=0
CFID=0x00091011, CFCS=0x02800006, CFRV=0x02000012, CFLT=0x0000FF00
CBIO=0xDFEFFF81, CBMA=0x49000000, CFIT=0x000001D1, CFDA=0x0000EF00
MII registers:
Register 0x00:   0400  784B  2000  5C01  0081  0000  0000  0000
Register 0x08:   0000  0000  0000  0000  0000  0000  0000  0000
Register 0x10:   0000  0000  0000  0000        0000  0001  8060
Register 0x18:   8020  0800  0000  3800  A3B9
Software MAC address filter(hash:length/addr/mask/hits):
need_af_check = 0
0x00:  0  ffff.ffff.ffff  0000.0000.0000         0
0x10:  0  0009.443e.8854  0000.0000.0000         0
throttled=0, enabled=0, disabled=0
rx_fifo_overflow=0, rx_no_enp=0, rx_state=0
tx_underrun_err=0, tx_jabber_timeout=0, tx_carrier_loss=1
tx_no_carrier=0, tx_late_collision=0, tx_excess_coll=0
tx_collision_cnt=0, tx_deferred=0, fatal_tx_err=0, tbl_overflow=0
rx_pak_len_err = 0, filtered_pak_cnt = 0
tx_limited=0(256)
HW addr filter: 0xE18E700, ISL Disabled
Entry= 0:  Addr=FFFF.FFFF.FFFF
Entry= 1:  Addr=FFFF.FFFF.FFFF
Entry= 2:  Addr=FFFF.FFFF.FFFF
Entry= 3:  Addr=FFFF.FFFF.FFFF
Entry= 4:  Addr=FFFF.FFFF.FFFF
Entry= 5:  Addr=FFFF.FFFF.FFFF
Entry= 6:  Addr=FFFF.FFFF.FFFF
Entry= 7:  Addr=FFFF.FFFF.FFFF
Entry= 8:  Addr=FFFF.FFFF.FFFF
Entry= 9:  Addr=FFFF.FFFF.FFFF
Entry=10:  Addr=FFFF.FFFF.FFFF
Entry=11:  Addr=FFFF.FFFF.FFFF
Entry=12:  Addr=FFFF.FFFF.FFFF
Entry=13:  Addr=FFFF.FFFF.FFFF
Entry=14:  Addr=FFFF.FFFF.FFFF
Entry=15:  Addr=0009.443E.8854

I have been googling around but nothing very concluant so far.

Any clues ?

Thanks.

Best regards.

Cheers,

--
Youssef BENGELLOUN-ZAHR ………………………………………………
Ingénieur Réseaux et Télécoms


Technopole de l'Aube  en Champagne - BP 601 - 10901 TROYES  Cedex 9
Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
Tel                 +33 (0) 825 000 720
Tel. direct      +33 (0) 1 77 35 59 14
Tel. portable  +33 (0) 6 22 42 63 80
Email            [email protected]
……………………………………………………………………………….....www.720.fr
_______________________________________________
cisco-nsp mailing list  [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
--
Youssef BENGELLOUN-ZAHR ………………………………………………
Ingénieur Réseaux et Télécoms


Technopole de l'Aube  en Champagne - BP 601 - 10901 TROYES  Cedex 9
Agence Paris : 6, rue Charles Floquet - 92120 MONTROUGE
Tel                 +33 (0) 825 000 720
Tel. direct      +33 (0) 1 77 35 59 14
Tel. portable  +33 (0) 6 22 42 63 80
Email            [email protected]
……………………………………………………………………………….....www.720.fr
_______________________________________________
cisco-nsp mailing list  [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/

_______________________________________________
cisco-nsp mailing list  [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/

Re: [c-nsp] 7204VXR rebooted by watchdog hard reset with PA-FE in slot 1

Reply via email to