Did anyone try 2 SCME-E modules in one cassis with new software? On 22 April 2010 15:41, Ruslan Pustovoytov <ru...@inbox.ru> wrote:
> We test this release in production from 20 april. > I see that bypass do not work if I take out any optics from SIP. It work > only when I reload SCE or take out SIP from chassis. > But I have no big experience with SCE. > > > > Did anybody try this release in production? >> >> 2010/4/17 Yann Gauteron <ygaute...@gmail.com> >> >> >> >>> 3.6 is out since Tuesday this week :-) >>> >>> 2010/3/18 Mikhail Schedrin <msched...@gmail.com> >>> >>> Sorry that I didn't answer so much time. >>> >>> >>>> As I got to know from cisco engineers 2 SCMs are supported only by >>>> software >>>> 3.6 that hasn't released yet. >>>> I did open TAC case, they don't know that 2 SCMs are not suported by >>>> 3.5.5. >>>> They also do not have 2 SCMs in a lab to test it :( >>>> >>>> On 3 March 2010 19:17, Ghattas Jacob <gates...@gmail.com> wrote: >>>> >>>> >>>> >>>>> Mikhail, >>>>> Be sure both sce have the same pkg installed before you insert the >>>>> >>>>> >>>> second >>>> >>>> >>>>> one to the sce. >>>>> Which version are you running as it should be 3.6 and higher... >>>>> >>>>> Jacob >>>>> >>>>> >>>>> On Wed, Mar 3, 2010 at 5:17 PM, Arie Vayner (avayner) < >>>>> >>>>> >>>> avay...@cisco.com>wrote: >>>> >>>> >>>>> Mikhail, >>>>>> >>>>>> I recommend you open a TAC case, as this could be a hardware problem, >>>>>> but it requires some debugging... >>>>>> >>>>>> Arie >>>>>> >>>>>> -----Original Message----- >>>>>> From: cisco-nsp-boun...@puck.nether.net >>>>>> [mailto:cisco-nsp-boun...@puck.nether.net] On Behalf Of Mikhail >>>>>> >>>>>> >>>>> Schedrin >>>> >>>> >>>>> Sent: Wednesday, March 03, 2010 11:46 >>>>>> To: cisco-nsp@puck.nether.net >>>>>> Subject: [c-nsp] SCE 8000 with 2*SCM-E >>>>>> >>>>>> Hi. >>>>>> Does anybody have the experince of using SCE8000 with two SCM-E >>>>>> >>>>>> >>>>> modules? >>>> >>>> >>>>> We >>>>>> got the second SCM-E couple of days ago and SCE always boots in >>>>>> >>>>>> >>>>> recovery >>>> >>>> >>>>> mode, when I install the second module. >>>>>> I could not find any documentation about installing and configuring >>>>>> the >>>>>> second SCM-E, I think it should work out of the box. Actually it does >>>>>> not. >>>>>> _______________________________________________ >>>>>> cisco-nsp mailing list cisco-nsp@puck.nether.net >>>>>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>>>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>>>>> >>>>>> _______________________________________________ >>>>>> cisco-nsp mailing list cisco-nsp@puck.nether.net >>>>>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>>>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>>>>> >>>>>> >>>>>> >>>>> >>>>> >>>> -- >>>> С уважением, >>>> Щедрин Михаил >>>> Начальник отдела ТП2 >>>> SkyNet Telecom http://sknt.ru >>>> Санкт-Петербург >>>> тел. +7 812 600-75-35 ext. 554 >>>> моб. +7 911 934-79-83 >>>> _______________________________________________ >>>> cisco-nsp mailing list cisco-nsp@puck.nether.net >>>> https://puck.nether.net/mailman/listinfo/cisco-nsp >>>> archive at http://puck.nether.net/pipermail/cisco-nsp/ >>>> >>>> >>>> >>> >>> >> >> >> >> > > _______________________________________________ > cisco-nsp mailing list cisco-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/cisco-nsp > archive at http://puck.nether.net/pipermail/cisco-nsp/ > -- С уважением, Щедрин Михаил Начальник отдела ТП2 SkyNet Telecom http://sknt.ru Санкт-Петербург тел. +7 812 600-75-35 ext. 554 моб. +7 911 934-79-83 _______________________________________________ cisco-nsp mailing list cisco-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/