Maybe you're actually using MGCP then? You still haven't shown the dial-peers on the gateway. Is that because you don't have any?
show run | section dial-peer On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote: > debug was turned on as shown below. > > > 1#debug voice ccapi inout > voip ccapi inout debugging is on > > made test calls and then show log, I see below output. > > 1#show log > Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 > flushes, 0 overruns, xml disabled, filtering disabled) > > No Active Message Discriminator. > > > No Inactive Message Discriminator. > > > Console logging: level debugging, 517 messages logged, xml disabled, > filtering disabled > Monitor logging: level debugging, 0 messages logged, xml disabled, > filtering disabled > Buffer logging: level debugging, 550 messages logged, xml disabled, > filtering disabled > Exception Logging: size (4096 bytes) > Count and timestamp logging messages: disabled > Persistent logging: disabled > > No active filter modules. > > Trap logging: level debugging, 620 message lines logged > Logging to 10.0.7.139 (udp port 514, audit disabled, > link up), > 435 message lines logged, > 0 message lines rate-limited, > 0 message lines dropped-by-MD, > xml disabled, sequence number disabled > filtering disabled > Logging to 10.0.8.12 (udp port 514, audit disabled, > link up), > 435 message lines logged, > 0 message lines rate-limited, > 0 message lines dropped-by-MD, > xml disabled, sequence number disabled > filtering disabled > Logging Source-Interface: VRF Name: > Loopback0 > > > I don't see any calls activity. > > > thanks > > ------------------------------ > *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com> > *Sent:* Wednesday, February 28, 2018 11:19 AM > > *To:* Hamu Ebiso > *Cc:* cisco-voip voyp list > *Subject:* Re: [cisco-voip] Need help configuring router for 911 with > POTS Lines connected to FXO port on the router > But you didn't send all the information, because your output doesn't show > the dial-peers. > > One method is to capture the output from "debug voip ccapi inout" and look > for the following line "Outgoing Dial-peer=" > > You also didn't address the regions either. Can you send that too? > > On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com> > wrote: > > I was just trying to give you all the information so that you will be able > to see the whole picture. > > Regarding your questions, I don't know how to check that. > > > ------------------------------ > *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com> > *Sent:* Wednesday, February 28, 2018 10:45 AM > > *To:* Hamu Ebiso > *Cc:* cisco-voip voyp list > *Subject:* Re: [cisco-voip] Need help configuring router for 911 with > POTS Lines connected to FXO port on the router > That's interesting that I asked for the dial-peer config, and you sent > everything but. > > Do you know how to confirm which dial-peer the gateway is using? > > On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com> > wrote: > > Below is gateway configuration > > > > > isdn switch-type primary-ni > ! > ! > trunk group FXO_EM > hunt-scheme sequential > translation-profile incoming Incoming > ! > ! > trunk group Local > hunt-scheme sequential > translation-profile outgoing outbound > ! > ! > trunk group LD > translation-profile outgoing outbound > ! > voice-card 0 > dspfarm > dsp services dspfarm > ! > ! > voice call send-alert > voice rtp send-recv > ! > voice service voip > ip address trusted list > ipv4 10.170.99.12 > ipv4 10.44.50.14 > ipv4 10.44.50.39 > no ip address trusted authenticate > clid substitute name > clid network-provided > allow-connections h323 to h323 > allow-connections h323 to sip > allow-connections sip to h323 > allow-connections sip to sip > redirect ip2ip > signaling forward unconditional > fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 > fallback pass-through g711ulaw > no fax-relay sg3-to-g3 > modem passthrough nse codec g711ulaw > sip > bind control source-interface Loopback0 > bind media source-interface Loopback0 > session transport tcp > min-se 360 session-expires 360 > ds0-num > header-passing > error-passthru > registrar server expires max 600 min 60 > early-offer forced > midcall-signaling passthru > no call service stop > ! > ! > voice class uri 10 sip > host ipv4:10.x.x.x > host ipv4:10..x.x.x > host ipv4:10..x.x.x > voice class codec 1 > codec preference 1 g711ulaw > codec preference 2 g729r8 > ! > voice class codec 2 > codec preference 1 g711ulaw > ! > ! > ! > ! > voice translation-rule 1 > rule 1 /^208343\(....\)$/ /1208343\1/ > ! > voice translation-rule 9 > rule 1 /5.../ /1208343\0/ > ! > voice translation-rule 10 > rule 1 /^911/ /911/ > rule 2 /^9911/ /911/ > ! > voice translation-rule 15 > ! > voice translation-rule 30 > rule 1 /^911/ /911/ > rule 2 /^9911/ /911/ > rule 4 /^9\(011.*\)/ /\1/ > rule 9 /^9\(.*\)/ /\1/ > ! > ! > voice translation-profile Add1 > translate calling 91 > translate called 1 > ! > voice translation-profile Inbound > translate called 1 > ! > voice translation-profile Strip9 > translate called 10 > ! > voice translation-profile block_profile > translate calling 15 > ! > voice translation-profile outbound > translate calling 10 > ! > ! > crypto pki token default removal timeout 0 > ! > ! > ! > ! > license udi pid CISCO3845-MB sn FOC123128X5 > license accept end user agreement > archive > log config > hidekeys > username admin privilege 15 password 7 105D1F0C > username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx. > ! > ! > controller T1 0/0/0 > shutdown > cablelength long 0db > ! > controller T1 0/1/0 > shutdown > cablelength long 0db > ! > ! > ! > ! > ! > ! > interface Loopback0 > ip address 10.x.x.x 255.255.255.128 > ! > interface GigabitEthernet0/0 > description uplink to Lan1 > ip address 10.x.x.x 255.255.255.252 > duplex auto > speed auto > media-type rj45 > ! > interface GigabitEthernet0/1 > description uplink to Lan2 > ip address 10.x.x.x 255.255.255.252 > duplex auto > speed auto > media-type rj45 > ! > router ospf 1 > auto-cost reference-bandwidth 10000 > network 10.0.0.0 0.0.255.255 area 10.0.0.0 > ! > ip forward-protocol nd > ! > ! > no ip http server > no ip http secure-server > ! > > >
_______________________________________________ cisco-voip mailing list cisco-voip@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip