Hi Anthony,
do you think I should change the setting between CUCM and Gateway to H.323 instead of SIP? do you think that makes it easy? Thanks Hamu ________________________________ From: Anthony Holloway <avholloway+cisco-v...@gmail.com> Sent: Thursday, March 1, 2018 1:16 PM To: Hamu Ebiso Cc: Cisco VoIP Group Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router debug voip ccapi inout, and if you're using SIP, then debug ccsip messages as well. the debug vpm signal is not very helpful, though it does show the port selected. On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso <hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote: Thank you Anthony very much for your help. The 19529473283<tel:(952)%20947-3283> for connection plar 19529473283<tel:(952)%20947-3283> I was testing with. After changing of few things on the gateway, I'm now seeing different messages when I run debug. The calls used to ring only one time and then fast busy, now it rings twice and then fax busy for incoming. for outgoing, it's says calls connot be completed as dialed. Attached the new logs again. I really appreciate your help. thanks again. Hamu ________________________________ From: Anthony Holloway <avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>> Sent: Thursday, March 1, 2018 11:05 AM To: Hamu Ebiso Cc: Cisco VoIP Group Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router According to the debug, you're calling 19529473283<tel:(952)%20947-3283>. Is that correct? Called Number=19529473283<tel:(952)%20947-3283>(TON=Unknown, NPI=Unknown), If so, then this debug is not for this gateway, because you're hitting Outgoing Dial-peer=5 Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE IS NON ISDN(3) And dial-peer 5, while it exists in your config you pasted, it doesn't match the called number. dial-peer voice 5 voip description FXO test destination-pattern 12083437020<tel:(208)%20343-7020> session target ipv4:10.0.2.5 ! Even if it did match the destination pattern, you're missing some config on this dial-peer to make a SIP capable dial-peer, which means it's sending H323 setup to CUCM. If you built the gateway as H323, then I can see how it rang your CIPC, otherwise, if you built it as SIP, which you said you did, then it would never ring your CIPC. So, something is not adding up here. Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too terrible, but it's also not good practice to be using dial-peer 0. It's really VoIP DP 0 that is messy though. Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=FALSE, On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote: Hi Anthony, yes the call was hitting the gateway because I was seeing FXO port going Off-Hook. The problem was that Logging was not setup in the gateway. After I setup the Logging, I'm now seeing logs. I have attached the log. thanks Hamu ________________________________ From: avhollo...@gmail.com<mailto:avhollo...@gmail.com> <avhollo...@gmail.com<mailto:avhollo...@gmail.com>> on behalf of Anthony Holloway <avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>> Sent: Thursday, March 1, 2018 8:45 AM To: Hamu Ebiso Cc: Cisco VoIP Group Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router Since you didn't see the call in your debugs, your call likely didn't hit your gateway. Can you confirm how you made your test call, when you had your debug running? On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote: Here is the dial-peer output 1#show run | sec dial-peer dial-peer voice 1 pots trunkgroup FXO_EM translation-profile incoming Inbound call-block translation-profile incoming block_profile call-block disconnect-cause incoming call-reject incoming called-number . direct-inward-dial dial-peer voice 911 pots trunkgroup FXO_EM description Services translation-profile outgoing Strip9 destination-pattern 911 dial-peer voice 9911 pots trunkgroup FXO_EM description Services translation-profile outgoing Strip9 destination-pattern 9911 dial-peer voice 2 voip description CUCM Dial-Peer - Inbound preference 1 destination-pattern 12086858038<tel:(208)%20685-8038> session protocol sipv2 session target ipv4:10.0.2.6 incoming uri via 10 voice-class codec 1 dtmf-relay rtp-nte sip-kpml fax-relay ecm disable fax nsf 000000 ip qos dscp cs3 signaling no vad dial-peer voice 3 voip preference 2 destination-pattern 12086858038<tel:(208)%20685-8038> session target ipv4:10.0.2.3 dial-peer voice 650 pots trunkgroup Local description Local outbound translation-profile outgoing Strip9 destination-pattern 9208....... dial-peer voice 4 pots trunkgroup FXO_EM description ** 10-digit Local Call ** translation-profile outgoing Strip9 destination-pattern ^9[2-9]..[2-9]......$ forward-digits 10 dial-peer voice 5 voip description FXO test destination-pattern 12083437020<tel:(208)%20343-7020> session target ipv4:10.0.2.5 thank you very much!! ________________________________ From: Anthony Holloway <avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>> Sent: Wednesday, February 28, 2018 1:29 PM To: Hamu Ebiso Cc: cisco-voip voyp list Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router Maybe you're actually using MGCP then? You still haven't shown the dial-peers on the gateway. Is that because you don't have any? show run | section dial-peer On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote: debug was turned on as shown below. 1#debug voice ccapi inout voip ccapi inout debugging is on made test calls and then show log, I see below output. 1#show log Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator. Console logging: level debugging, 517 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 0 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 550 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled No active filter modules. Trap logging: level debugging, 620 message lines logged Logging to 10.0.7.139 (udp port 514, audit disabled, link up), 435 message lines logged, 0 message lines rate-limited, 0 message lines dropped-by-MD, xml disabled, sequence number disabled filtering disabled Logging to 10.0.8.12 (udp port 514, audit disabled, link up), 435 message lines logged, 0 message lines rate-limited, 0 message lines dropped-by-MD, xml disabled, sequence number disabled filtering disabled Logging Source-Interface: VRF Name: Loopback0 I don't see any calls activity. thanks ________________________________ From: Anthony Holloway <avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>> Sent: Wednesday, February 28, 2018 11:19 AM To: Hamu Ebiso Cc: cisco-voip voyp list Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router But you didn't send all the information, because your output doesn't show the dial-peers. One method is to capture the output from "debug voip ccapi inout" and look for the following line "Outgoing Dial-peer=" You also didn't address the regions either. Can you send that too? On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote: I was just trying to give you all the information so that you will be able to see the whole picture. Regarding your questions, I don't know how to check that. ________________________________ From: Anthony Holloway <avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>> Sent: Wednesday, February 28, 2018 10:45 AM To: Hamu Ebiso Cc: cisco-voip voyp list Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router That's interesting that I asked for the dial-peer config, and you sent everything but. Do you know how to confirm which dial-peer the gateway is using? On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote: Below is gateway configuration isdn switch-type primary-ni ! ! trunk group FXO_EM hunt-scheme sequential translation-profile incoming Incoming ! ! trunk group Local hunt-scheme sequential translation-profile outgoing outbound ! ! trunk group LD translation-profile outgoing outbound ! voice-card 0 dspfarm dsp services dspfarm ! ! voice call send-alert voice rtp send-recv ! voice service voip ip address trusted list ipv4 10.170.99.12 ipv4 10.44.50.14 ipv4 10.44.50.39 no ip address trusted authenticate clid substitute name clid network-provided allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip redirect ip2ip signaling forward unconditional fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw no fax-relay sg3-to-g3 modem passthrough nse codec g711ulaw sip bind control source-interface Loopback0 bind media source-interface Loopback0 session transport tcp min-se 360 session-expires 360 ds0-num header-passing error-passthru registrar server expires max 600 min 60 early-offer forced midcall-signaling passthru no call service stop ! ! voice class uri 10 sip host ipv4:10.x.x.x host ipv4:10..x.x.x host ipv4:10..x.x.x voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! voice class codec 2 codec preference 1 g711ulaw ! ! ! ! voice translation-rule 1 rule 1 /^208343\(....\)$/ /1208343\1/ ! voice translation-rule 9 rule 1 /5.../ /1208343\0/ ! voice translation-rule 10 rule 1 /^911/ /911/ rule 2 /^9911/ /911/ ! voice translation-rule 15 ! voice translation-rule 30 rule 1 /^911/ /911/ rule 2 /^9911/ /911/ rule 4 /^9\(011.*\)/ /\1/ rule 9 /^9\(.*\)/ /\1/ ! ! voice translation-profile Add1 translate calling 91 translate called 1 ! voice translation-profile Inbound translate called 1 ! voice translation-profile Strip9 translate called 10 ! voice translation-profile block_profile translate calling 15 ! voice translation-profile outbound translate calling 10 ! ! crypto pki token default removal timeout 0 ! ! ! ! license udi pid CISCO3845-MB sn FOC123128X5 license accept end user agreement archive log config hidekeys username admin privilege 15 password 7 105D1F0C username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx. ! ! controller T1 0/0/0 shutdown cablelength long 0db ! controller T1 0/1/0 shutdown cablelength long 0db ! ! ! ! ! ! interface Loopback0 ip address 10.x.x.x 255.255.255.128 ! interface GigabitEthernet0/0 description uplink to Lan1 ip address 10.x.x.x 255.255.255.252 duplex auto speed auto media-type rj45 ! interface GigabitEthernet0/1 description uplink to Lan2 ip address 10.x.x.x 255.255.255.252 duplex auto speed auto media-type rj45 ! router ospf 1 auto-cost reference-bandwidth 10000 network 10.0.0.0 0.0.255.255 area 10.0.0.0 ! ip forward-protocol nd ! ! no ip http server no ip http secure-server !
_______________________________________________ cisco-voip mailing list cisco-voip@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip