Since you didn't see the call in your debugs, your call likely didn't hit your gateway.
Can you confirm how you made your test call, when you had your debug running? On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com> wrote: > Here is the dial-peer output > > 1#show run | sec dial-peer > dial-peer voice 1 pots > trunkgroup FXO_EM > translation-profile incoming Inbound > call-block translation-profile incoming block_profile > call-block disconnect-cause incoming call-reject > incoming called-number . > direct-inward-dial > dial-peer voice 911 pots > trunkgroup FXO_EM > description Services > translation-profile outgoing Strip9 > destination-pattern 911 > dial-peer voice 9911 pots > trunkgroup FXO_EM > description Services > translation-profile outgoing Strip9 > destination-pattern 9911 > dial-peer voice 2 voip > description CUCM Dial-Peer - Inbound > preference 1 > destination-pattern 12086858038 <(208)%20685-8038> > session protocol sipv2 > session target ipv4:10.0.2.6 > incoming uri via 10 > voice-class codec 1 > dtmf-relay rtp-nte sip-kpml > fax-relay ecm disable > fax nsf 000000 > ip qos dscp cs3 signaling > no vad > dial-peer voice 3 voip > preference 2 > destination-pattern 12086858038 <(208)%20685-8038> > session target ipv4:10.0.2.3 > dial-peer voice 650 pots > trunkgroup Local > description Local outbound > translation-profile outgoing Strip9 > destination-pattern 9208....... > dial-peer voice 4 pots > trunkgroup FXO_EM > description ** 10-digit Local Call ** > translation-profile outgoing Strip9 > destination-pattern ^9[2-9]..[2-9]......$ > forward-digits 10 > dial-peer voice 5 voip > description FXO test > destination-pattern 12083437020 <(208)%20343-7020> > session target ipv4:10.0.2.5 > > > thank you very much!! > > ------------------------------ > *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com> > *Sent:* Wednesday, February 28, 2018 1:29 PM > *To:* Hamu Ebiso > *Cc:* cisco-voip voyp list > *Subject:* Re: [cisco-voip] Need help configuring router for 911 with > POTS Lines connected to FXO port on the router > > Maybe you're actually using MGCP then? You still haven't shown the > dial-peers on the gateway. Is that because you don't have any? > > show run | section dial-peer > > On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com> > wrote: > > debug was turned on as shown below. > > > 1#debug voice ccapi inout > voip ccapi inout debugging is on > > made test calls and then show log, I see below output. > > 1#show log > Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 > flushes, 0 overruns, xml disabled, filtering disabled) > > No Active Message Discriminator. > > > No Inactive Message Discriminator. > > > Console logging: level debugging, 517 messages logged, xml disabled, > filtering disabled > Monitor logging: level debugging, 0 messages logged, xml disabled, > filtering disabled > Buffer logging: level debugging, 550 messages logged, xml disabled, > filtering disabled > Exception Logging: size (4096 bytes) > Count and timestamp logging messages: disabled > Persistent logging: disabled > > No active filter modules. > > Trap logging: level debugging, 620 message lines logged > Logging to 10.0.7.139 (udp port 514, audit disabled, > link up), > 435 message lines logged, > 0 message lines rate-limited, > 0 message lines dropped-by-MD, > xml disabled, sequence number disabled > filtering disabled > Logging to 10.0.8.12 (udp port 514, audit disabled, > link up), > 435 message lines logged, > 0 message lines rate-limited, > 0 message lines dropped-by-MD, > xml disabled, sequence number disabled > filtering disabled > Logging Source-Interface: VRF Name: > Loopback0 > > > I don't see any calls activity. > > > thanks > > ------------------------------ > *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com> > *Sent:* Wednesday, February 28, 2018 11:19 AM > > *To:* Hamu Ebiso > *Cc:* cisco-voip voyp list > *Subject:* Re: [cisco-voip] Need help configuring router for 911 with > POTS Lines connected to FXO port on the router > But you didn't send all the information, because your output doesn't show > the dial-peers. > > One method is to capture the output from "debug voip ccapi inout" and look > for the following line "Outgoing Dial-peer=" > > You also didn't address the regions either. Can you send that too? > > On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com> > wrote: > > I was just trying to give you all the information so that you will be able > to see the whole picture. > > Regarding your questions, I don't know how to check that. > > > ------------------------------ > *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com> > *Sent:* Wednesday, February 28, 2018 10:45 AM > > *To:* Hamu Ebiso > *Cc:* cisco-voip voyp list > *Subject:* Re: [cisco-voip] Need help configuring router for 911 with > POTS Lines connected to FXO port on the router > That's interesting that I asked for the dial-peer config, and you sent > everything but. > > Do you know how to confirm which dial-peer the gateway is using? > > On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com> > wrote: > > Below is gateway configuration > > > > > isdn switch-type primary-ni > ! > ! > trunk group FXO_EM > hunt-scheme sequential > translation-profile incoming Incoming > ! > ! > trunk group Local > hunt-scheme sequential > translation-profile outgoing outbound > ! > ! > trunk group LD > translation-profile outgoing outbound > ! > voice-card 0 > dspfarm > dsp services dspfarm > ! > ! > voice call send-alert > voice rtp send-recv > ! > voice service voip > ip address trusted list > ipv4 10.170.99.12 > ipv4 10.44.50.14 > ipv4 10.44.50.39 > no ip address trusted authenticate > clid substitute name > clid network-provided > allow-connections h323 to h323 > allow-connections h323 to sip > allow-connections sip to h323 > allow-connections sip to sip > redirect ip2ip > signaling forward unconditional > fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 > fallback pass-through g711ulaw > no fax-relay sg3-to-g3 > modem passthrough nse codec g711ulaw > sip > bind control source-interface Loopback0 > bind media source-interface Loopback0 > session transport tcp > min-se 360 session-expires 360 > ds0-num > header-passing > error-passthru > registrar server expires max 600 min 60 > early-offer forced > midcall-signaling passthru > no call service stop > ! > ! > voice class uri 10 sip > host ipv4:10.x.x.x > host ipv4:10..x.x.x > host ipv4:10..x.x.x > voice class codec 1 > codec preference 1 g711ulaw > codec preference 2 g729r8 > ! > voice class codec 2 > codec preference 1 g711ulaw > ! > ! > ! > ! > voice translation-rule 1 > rule 1 /^208343\(....\)$/ /1208343\1/ > ! > voice translation-rule 9 > rule 1 /5.../ /1208343\0/ > ! > voice translation-rule 10 > rule 1 /^911/ /911/ > rule 2 /^9911/ /911/ > ! > voice translation-rule 15 > ! > voice translation-rule 30 > rule 1 /^911/ /911/ > rule 2 /^9911/ /911/ > rule 4 /^9\(011.*\)/ /\1/ > rule 9 /^9\(.*\)/ /\1/ > ! > ! > voice translation-profile Add1 > translate calling 91 > translate called 1 > ! > voice translation-profile Inbound > translate called 1 > ! > voice translation-profile Strip9 > translate called 10 > ! > voice translation-profile block_profile > translate calling 15 > ! > voice translation-profile outbound > translate calling 10 > ! > ! > crypto pki token default removal timeout 0 > ! > ! > ! > ! > license udi pid CISCO3845-MB sn FOC123128X5 > license accept end user agreement > archive > log config > hidekeys > username admin privilege 15 password 7 105D1F0C > username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx. > ! > ! > controller T1 0/0/0 > shutdown > cablelength long 0db > ! > controller T1 0/1/0 > shutdown > cablelength long 0db > ! > ! > ! > ! > ! > ! > interface Loopback0 > ip address 10.x.x.x 255.255.255.128 > ! > interface GigabitEthernet0/0 > description uplink to Lan1 > ip address 10.x.x.x 255.255.255.252 > duplex auto > speed auto > media-type rj45 > ! > interface GigabitEthernet0/1 > description uplink to Lan2 > ip address 10.x.x.x 255.255.255.252 > duplex auto > speed auto > media-type rj45 > ! > router ospf 1 > auto-cost reference-bandwidth 10000 > network 10.0.0.0 0.0.255.255 area 10.0.0.0 > ! > ip forward-protocol nd > ! > ! > no ip http server > no ip http secure-server > ! > > >
_______________________________________________ cisco-voip mailing list cisco-voip@puck.nether.net https://puck.nether.net/mailman/listinfo/cisco-voip
