Yeah it's a HSSI cable... CAB-HSI1 is the part. Telco is using the default
HDLC for encapsulation.
I've got telco coming out today to test the line. According to Kentrox's
doc, a T3 w/HSSI interface has an allowed range of 1-35MHz; or 45 if both
are set to 45MHz. I currently have the transmit and receive set at 12MHz.
Below is the "sh contr hssi1/0".... Interesting, received clockrate says
1582! Shouldn't that be 12000?
M1T-HSSI-B: show controller:
PAS unit 0, subunit 0, f/w version 3-92, rev ID 0x2800001, version 3
idb = 0x621D1178, ds = 0x621D2E70, ssb=0x621D31A4
Clock mux=0x31, ucmd_ctrl=0x8, port_status=0x5
Serial config=0x8, line config=0x1B0202, rx line config=0x80202
maxdgram=4584, bufpool=128Kb, 120 particles
LC=down CA=down TM=down LB=down TA=up LA=down
line state: down
HSSI DTE, received clockrate 1582
base0 registers=0x3C800000, base1 registers=0x3C802000
rx_base0 registers=0x3C900000, rx_base1 registers=0x3C902000
mxt_ds=0x62684E5C, rx ring entries=124, tx ring entries=126
statring=0x7CD1FA0, statr shadow=0x621D39AC, stat_head=0
plus_pa: rx_statring=0x7CD21E0, rx_statr shadow=0x621D3DD8, rx_stat_head=0
rxring=0x7CD1D60, rxr shadow=0x621D3380, rx_head=0
txring=0x7CD27A0, txr shadow=0x621D4204, tx_head=0, tx_tail=0, tx_count=0
throttled=0, enabled=0
halted=0, last halt reason=0
Microcode fatal errors=0
rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0
rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0xC
tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(126)
tx_fullring=0, tx_started=0
rx_int_count=0, tx_int_count=0
Thanks for all your input!!!!
Cheers,
Mike J
-----Original Message-----
From: s vermill [mailto:[EMAIL PROTECTED]
Sent: Tuesday, July 29, 2003 2:30 PM
To: [EMAIL PROTECTED]
Subject: RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129]
Jablonski, Michael wrote:
>
> Has anyone had any experience w/the following combination?
>
> 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU
>
> I've been trying, to no avail, to bring the HSSI up for a 12M
> DS3.... The
> CSU/DSU, according to the lights, is ready to send and receive
> data; but
> when I bring up the int on the router, it shows down down.
Are you sure you have a HSSI cable? SCSI 2 will physically fit the
connectors, but is pinned out very differently. Make sure that's good to
go...
> Here's the
> router info:
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~
> interface Hssi1/0
> bandwidth 12000
> ip address x.x.x.x 255.255.255.252
> serial restart_delay 0
> no cdp enable
>
> Hssi1/0 is down, line protocol is down
> Hardware is M1T-HSSI-B
> Internet address is x.x.x.x/30
> MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation HDLC, crc 16, loopback not set
> Keepalive set (10 sec)
> Restart-Delay is 0 secs
> Last input never, output never, output hang never
> Last clearing of "show interface" counters never
> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output
> drops: 0
> Queueing strategy: fifo
> Output queue :0/40 (size/max)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 0 packets input, 0 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 parity
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0
> abort
> 0 packets output, 0 bytes, 0 underruns
> 0 output errors, 0 applique, 8 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 13 carrier transitions LC=down CA=down TM=down
> LB=down TA=up
> LA=down
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=73239&t=73129
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
