Resolved!!! Turns out our equipment provider sent us the wrong cable.... They sent the HSSI Null Modem cable (CAB-HNUL) and not the CAB-HSI1!
Thanks for everyone's insight. Cheers, MKJ -----Original Message----- From: Jablonski, Michael [mailto:[EMAIL PROTECTED] Sent: Wednesday, July 30, 2003 8:56 AM To: [EMAIL PROTECTED] Subject: RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Yeah it's a HSSI cable... CAB-HSI1 is the part. Telco is using the default HDLC for encapsulation. I've got telco coming out today to test the line. According to Kentrox's doc, a T3 w/HSSI interface has an allowed range of 1-35MHz; or 45 if both are set to 45MHz. I currently have the transmit and receive set at 12MHz. Below is the "sh contr hssi1/0".... Interesting, received clockrate says 1582! Shouldn't that be 12000? M1T-HSSI-B: show controller: PAS unit 0, subunit 0, f/w version 3-92, rev ID 0x2800001, version 3 idb = 0x621D1178, ds = 0x621D2E70, ssb=0x621D31A4 Clock mux=0x31, ucmd_ctrl=0x8, port_status=0x5 Serial config=0x8, line config=0x1B0202, rx line config=0x80202 maxdgram=4584, bufpool=128Kb, 120 particles LC=down CA=down TM=down LB=down TA=up LA=down line state: down HSSI DTE, received clockrate 1582 base0 registers=0x3C800000, base1 registers=0x3C802000 rx_base0 registers=0x3C900000, rx_base1 registers=0x3C902000 mxt_ds=0x62684E5C, rx ring entries=124, tx ring entries=126 statring=0x7CD1FA0, statr shadow=0x621D39AC, stat_head=0 plus_pa: rx_statring=0x7CD21E0, rx_statr shadow=0x621D3DD8, rx_stat_head=0 rxring=0x7CD1D60, rxr shadow=0x621D3380, rx_head=0 txring=0x7CD27A0, txr shadow=0x621D4204, tx_head=0, tx_tail=0, tx_count=0 throttled=0, enabled=0 halted=0, last halt reason=0 Microcode fatal errors=0 rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0 rx_no_buf=0, rx_soft_overrun_err=0, dump_err= 0, bogus=0, mxt_flags=0xC tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0(126) tx_fullring=0, tx_started=0 rx_int_count=0, tx_int_count=0 Thanks for all your input!!!! Cheers, Mike J -----Original Message----- From: s vermill [mailto:[EMAIL PROTECTED] Sent: Tuesday, July 29, 2003 2:30 PM To: [EMAIL PROTECTED] Subject: RE: NM-1HSSI w/kentrox DataSMART T3/E3 [7:73129] Jablonski, Michael wrote: > > Has anyone had any experience w/the following combination? > > 3640 & NM-1HSSI & Kentrox DataSMART T3/E3 IDSU > > I've been trying, to no avail, to bring the HSSI up for a 12M > DS3.... The > CSU/DSU, according to the lights, is ready to send and receive > data; but > when I bring up the int on the router, it shows down down. Are you sure you have a HSSI cable? SCSI 2 will physically fit the connectors, but is pinned out very differently. Make sure that's good to go... > Here's the > router info: > ~~~~~~~~~~~~~~~~~~~~~~~~~~~ > interface Hssi1/0 > bandwidth 12000 > ip address x.x.x.x 255.255.255.252 > serial restart_delay 0 > no cdp enable > > Hssi1/0 is down, line protocol is down > Hardware is M1T-HSSI-B > Internet address is x.x.x.x/30 > MTU 4470 bytes, BW 12000 Kbit, DLY 200 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation HDLC, crc 16, loopback not set > Keepalive set (10 sec) > Restart-Delay is 0 secs > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output > drops: 0 > Queueing strategy: fifo > Output queue :0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 parity > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 > abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 applique, 8 interface resets > 0 output buffer failures, 0 output buffers swapped out > 13 carrier transitions LC=down CA=down TM=down > LB=down TA=up > LA=down Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=73247&t=73129 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
