1) If your colleages sent you the config files from the 5505 switch fabric
then it would look similar to the second line "somertarou>(enable)";
however, your colleagues sent you the config off of the supervisor engine.
2) To get the to the switch fabric, get the address of the fabric and telnet
to that.
Stevan Pierce
""Sim, CT (Chee Tong)"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi..Dear friends, I was very confused with the confuration file of 5505,
my
> colleages send me two configuration file in Tokyo.
>
> One start with SOMETAROU#sh conf
>
> Another one start with sometarou> (enable) sh conf
>
> and two of them give me different configuration, (see below)
>
> 1)can any one tell me, what is the different?
>
> 2)I can telnet to my backbone switches, after I type 5505>en password
> it gives me 5505>(enable) prompt then what should I type to get the 5505#
> prompt
>
> 3)What is the special function 5505 back bone switch? Can you use normal
> switch like 1900, 2900 to replace it? (optional)
>
>
>
&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
> &&&&&&
> SOMETAROU#sh conf
> Using 1961 out of 126968 bytes
> !
> version 11.2
> no service password-encryption
> no service udp-small-servers
> no service tcp-small-servers
> !
> hostname SOMETAROU
> !
> enable secret 5 $1$0U5tyfSAgpNPpsjXQ4xGI/
> !
> !
> interface Vlan1
> description RABO-JP
> ip address 57.198.45.251 255.255.255.0
> ip broadcast-address 57.198.45.255
> no ip redirects
> standby 1 priority 100
> standby 1 preempt
> standby 1 ip 57.198.45.250
> !
>
&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
> &&&&&&&&
> sometarou> (enable) sh conf
> .....
> ..........
> .........
> ..........
> ..........
> ..........
> ..
>
> begin
> set password $1$PEV9$MXJwjj4umvPJ7aj.0KeUa.
> set enablepass $1$3Las$CDZgLGUVTKg7qozn9jnsK0
> set prompt Console>
> set length 24 default
> set logout 20
> set banner motd ^C
>
> ********************
> * Catalyst 5505 #2 *
> * SupervisorEngine *
> * sometarou *
> ********************
> ^C
> !
> #system
> set system baud 9600
> set system modem disable
> set system name sometarou
> set system location
> set system contact
> !
> #snmp
> set snmp community read-only public
> set snmp community read-write private
> set snmp community read-write-all secret
> set snmp rmon disable
> set snmp trap disable module
> set snmp trap disable chassis
> set snmp trap disable bridge
>
>
> ==================================================================
> De informatie opgenomen in dit bericht kan vertrouwelijk zijn en
> is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht
> onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en
> de afzender direct te informeren door het bericht te retourneren.
> ==================================================================
> The information contained in this message may be confidential
> and is intended to be exclusively for the addressee. Should you
> receive this message unintentionally, please do not use the contents
> herein and notify the sender immediately by return e-mail.
>
>
> ==================================================================
>
> ___________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> ---
___________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
