Thanks very much guys. Keep up the good work.
Ash
Timothy Mark Jones wrote:
> From the following URL:
>
> http://www.cisco.com/warp/customer/473/34.shtml
>
> Pinnacle Synch Failed
>
> Problem: The "Pinnacle Synch Failed" error message is displayed at bootup.
>
> Platform: Catalyst 6000 family switches
>
> The following is an example of the console output you will see when this
> error occurs:
>
> System Power On Diagnostics Complete
>
> Boot image: bootflash:cat6000-sup.5-4-4.bin
>
> In Local Test Mode, Synch Failed. Retries: 4
>
> Local Test Mode encounters Minor hardware problem in Module # 1
>
> Running System Diagnostics from this Supervisor (Module 1)
> This may take up to 2 minutes....please wait
> Pinnacle Synch Failed. Retries: 4
>
> Minor hardware problem in Module # 1
> Use 'show test 1' to see results of tests.
>
> Cisco Systems Console
>
> Enter password:
> The workaround is to power off the switch and then make certain that:
>
> The supervisor engine(s) and all switching modules are firmly seated in the
> chassis backplane
> The ejector levers on the left and right sides of the modules are fully
> engaged (pressed completely against the front panel of the module)
> The thumb screws on the left and right sides of the modules are screwed into
> the card cage and are tightened hand-tight
> After ensuring that all modules are properly engaged in the chassis, power
> on the chassis.
>
> If you still see "Pinnacle Synch Failed" messages, there might be a hardware
> problem with one of the modules.
>
> Power off the switch and remove all switching modules. Power on the switch
> with just the supervisor engine in the chassis. Repeat the process adding
> one module at a time until the problem module is identified.
>
> .
>
> Timothy Mark Jones
> Network Engineer
> Cisco CCNA, CCNP, CCDA, CCDP
> Ficomp, Inc.
> Pager: 800-759-8888 PIN#1279088
>
> "Ashfaq Aslam" <[EMAIL PROTECTED]> wrote in message
> [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > Hi chaps,
> >
> > I have a Cisco 6500 Router at work and when I power on the router just
> > after the router self-test it displays error message "Pinnacle not
> > syncronised". Does anyone have any ideas as to what this means or why
> it's
> > coming up.
> >
> > Thanks for your help !!!
> >
> > Best Rgds,
> > Ash
> >
> > **NOTE: New CCNA/CCDA List has been formed. For more information go to
> > http://www.groupstudy.com/list/Associates.html
> > _________________________________
> > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> > FAQ, list archives, and subscription info: http://www.groupstudy.com
> > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
> >
>
> **NOTE: New CCNA/CCDA List has been formed. For more information go to
> http://www.groupstudy.com/list/Associates.html
> _________________________________
> UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
> FAQ, list archives, and subscription info: http://www.groupstudy.com
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associates.html
_________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
