Manishkumar,
clear line 1-16 will reset your connection
-Frank
On 3 Nov 2000, Manishkumar Patel wrote:
> Dear All,
> Hi!
> I have setup 2511 as Terminal Server, with the Octal RJ-45 cables connected to
> Console port of 4 2500 Routers. During a day the reverse Telnet works fine,
> but when I try to Telnet on next day morning, it says " CONNECTION REFUSED",
> What can be the Problem & solution?
>
> It works fine after Rebooting the Terminal Server.
> Your help will be appreciated.
> Thanks in advance...Have a nice weekend.
> Regards
> MK
> Andre Fecteau <[EMAIL PROTECTED]> wrote:
>
> > ---------------------------------------------
> > Attachment:
> > MIME Type: multipart/alternative
> > ---------------------------------------------
> > I configured some routers for ISDN, but one of the spids is coming up
> > invalid can anyone tell me why? I put the BRI configurations for both
> > sides as well as the error message that I'm getting. Can someone help
> > me fix this problem? By the way I called the service provider and they
> > said everything is OK regarding the ISDN lines and spids. I can telnet
> > and other things, but I just can't get both channels to come up at the
> > same time. And obviously at least from my limited knowledge base the
> > invalid spid has something to do with that! I've been pulling my hair
> > out over this one for a few days! I'd like a solution, but all
> > suggestions are more than welcome!!!!!!!
> >
> > Both side have this:
> > isdn switch-type basic-ni
> > isdn voice-call-failure 0
> > isdn tei-negotiation first-call
> >
> > One side
> > interface BRI1/1
> > ip address x.x.x.x x.x.x.x
> > ip nat inside
> > encapsulation ppp
> > dialer map ip y.y.y.y name y broadcast yyyyyyy(first #)
> > dialer map ip y.y.y.y name y broadcast yyyyyyy(second #)
> > dialer load-threshold 10 either
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 xxxxxxxxxxxxxx xxxxxxx
> > isdn spid2 xxxxxxxxxxxxxx xxxxxxx
> > ppp authentication chap
> > ppp multilink
> > !
> >
> > Other side:
> > !
> > interface BRI1/0
> > ip address y.y.y.y y.y.y.y
> > encapsulation ppp
> > dialer map ip x.x.x.x name x broadcast xxxxxxx(first #)
> > dialer map ip x.x.x.x name x broadcast xxxxxxx(second #)
> > dialer load-threshold 1 outbound
> > dialer-group 1
> > isdn switch-type basic-ni
> > isdn spid1 yyyyyyyyyyyyyy yyyyyyy
> > isdn spid2 yyyyyyyyyyyyyy yyyyyyy
> > ppp authentication chap
> > ppp multilink
> > !
> >
> > This is the ISDN status : The other side is the same except both spids
> > are valid!
> > Global ISDN Switchtype = basic-ni
> > ISDN BRI1/0 interface
> > dsl 8, interface ISDN Switchtype = basic-ni
> > Layer 1 Status:
> > ACTIVE
> > Layer 2 Status:
> > TEI = 73, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > TEI = 74, Ces = 2, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
> > TEI 73, ces = 1, state = 5(init)
> > spid1 configured, spid1 NOT sent, spid1 valid
> > Endpoint ID Info: epsf = 0, usid = 40, tid = 1
> > TEI 74, ces = 2, state = 4(await init)
> > spid2 configured, spid2 sent, spid2 NOT valid
> > Layer 3 Status:
> > 0 Active Layer 3 Call(s)
> > Activated dsl 8 CCBs = 0
> > The Free Channel Mask: 0x80000003
> >
> > Help!
> > Andre
> >
> >
> > --
> > Andre Fecteau
> > Unix Software Engineer
> > [EMAIL PROTECTED]
> > CNE3, 4 & CCNA
> >
>
>
> ____________________________________________________________________
> Get free email and a permanent address at http://www.netaddress.com/?N=1
>
> _________________________________
> FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]