I had a similar problem to ports 3/7 and 3/8 and it was a duplex mismatch.
The ports were set to full but the nic couldn't decide whether to operate at
full or half. Hard setting the duplex on the PC's it fixed the problem and
made the users VERY happy. They were getting less than a third of the line
speed!
Tim
> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> Sim, CT (Chee Tong)
> Sent: Monday, February 19, 2001 7:18 AM
> To: 'Brant Stevens'; [EMAIL PROTECTED]; Santosh Koshy;
> [EMAIL PROTECTED]
> Subject: error on the show port counter on catalyst5505
>
>
> Dear all,
>
> I did a show port conter command in my catalyst 5505 switches and
> result as
> below. Can I verify with you that whether the below is correct or not?
> 1) many Align-Err-FCS-Err counter mean the quality of the cable not good?
> 2) many Single/Multi/Late- mean the duplex type not match?
> 3)What is the problem if I got many "Runts" and " Giant" counter?
> 4)If I got many these port error, will it slow down the whole network or
> just the PC attached to the port?
>
> Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
> ----- ---------- ---------- ---------- ---------- ---------
> 1/1 0 0 0 0 0
> 1/2 0 0 0 0 0
> 3/1 0 0 0 0 0
> 3/2 0 0 0 0 0
> 3/3 0 0 0 0 0
> 3/4 0 0 0 0 0
> 3/5 0 3119 0 0 0
> 3/6 57 49 0 0 0
> 3/7 14189 14295 0 0 0
> 3/8 13578 12992 0 0 0
>
> Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts
> Giants
> ----- ---------- ---------- ---------- ---------- --------- ---------
> ---------
> 1/1 0 0 0 0 0 0
> 0
> 1/2 0 0 0 0 0 0
> 0
> 3/1 0 0 0 0 0 0
> -
> 3/2 0 0 0 0 0 0
> -
> 3/3 0 0 0 0 0 0
> -
> 3/4 0 0 0 0 0 0
> -
> 3/5 0 0 0 0 0 996
> 0
> 3/6 0 0 0 0 0 7
> 0
> 3/7 0 0 0 0 0 509
> 0
> 3/8 0 0 0 0 0 733
> 0
>
> ==================================================================
> De informatie opgenomen in dit bericht kan vertrouwelijk zijn en
> is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht
> onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en
> de afzender direct te informeren door het bericht te retourneren.
> ==================================================================
> The information contained in this message may be confidential
> and is intended to be exclusively for the addressee. Should you
> receive this message unintentionally, please do not use the contents
> herein and notify the sender immediately by return e-mail.
>
>
> ==================================================================
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]