Output from Stack decoder on Cisco website...
----------------------------------------------------------------------------
----
Session ID: 000000003A9106E8718A
General Diagnosis:
Hardware:
No failures detected.
Software:
rsym error: No symbols found found, please contact the TAC to assist in
diagnosing this problem
Bug Citations
Below are possible bug report citations that may be relevant to the cause of
your Stack Trace.
Citations with the highest score are the closest fit, with those having
scores of 0.90 or higher
being the most likely candidates.
Score Severity Bugid Version Fixed in: Feature Title
----------------------------------------------------------------------------
----
[Stack Decoder] [CCO Home Page] [Help]
-----Original Message-----
From: Peter Ching [mailto:[EMAIL PROTECTED]]
Sent: 19 February 2001 13:45
To: 'Andrew Larkins'
Subject: RE: Router crash - what does output mean
Any changes applied on the router hw/sw/configuration-wise?
> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> Andrew Larkins
> Sent: Monday, 19 February 2001 10:20 PM
> To: Peter Ching; [EMAIL PROTECTED]
> Subject: RE: Router crash - what does output mean
>
>
> Show ver is below as well as show stack
>
> SAFCOVER>sh stack
> Minimum process stacks:
> Free/Size Name
> 5504/6000 IPX Router Init
> 5584/6000 Call Management
> 11388/12000 Router Init
> 9356/12000 Init
> 5300/6000 RADIUS INITCONFIG
> 2464/3000 IP Gratuitous ARP
> 8040/9000 DHCP Client
> 4576/6000 RSRB Connector
> 9968/12000 Exec
> 9776/12000 Virtual Exec
> 5160/6000 TCP Echo
>
> Interrupt level stacks:
> Level Called Unused/Size Name
> 1 584366 7412/9000 Network interfaces
> 2 121709 8596/9000 DMA/Timer Interrupt
> 3 0 9000/9000 PA Management Int Handler
> 4 3446 8544/9000 Console Uart
> 5 0 9000/9000 External Interrupt
> 7 2432493 8604/9000 NMI Interrupt Handler
>
> System was restarted by error - a Software forced crash, PC 0x603503CC
> 3600 Software (C3640-DS-M), Version 12.1(5a), RELEASE SOFTWARE (fc1)
> Compiled Thu 16-Nov-00 18:23 by cmong (current version)
> Image text-base: 0x60008940, data-base: 0x60F8C000
>
>
> Stack trace from system failure:
> FP: 0x61D70718, RA: 0x603503CC
> FP: 0x61D70718, RA: 0x6034E880
> FP: 0x61D70730, RA: 0x60332D6C
> FP: 0x61D70768, RA: 0x606CF370
> FP: 0x61D70790, RA: 0x606CF468
> FP: 0x61D707B8, RA: 0x606D6B78
> FP: 0x61D70808, RA: 0x606C7BA0
> FP: 0x61D70820, RA: 0x606C8964
>
> SAFCOVER>
>
> -----Original Message-----
> From: Peter Ching [mailto:[EMAIL PROTECTED]]
> Sent: 19 February 2001 12:56
> To: [EMAIL PROTECTED]
> Subject: RE: Router crash - what does output mean
>
>
> I think you'll need to open a Cisco TAC case for this one,
> but send the 'show stack' and 'show version'
>
> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> Andrew Larkins
> Sent: Monday, 19 February 2001 8:33 PM
> To: Cisco Mail List
> Subject: Router crash - what does output mean
> Importance: High
>
>
> Hi all,
>
> Our Cisco 3640 router at the DRP site crashed. Router was in
> "rommon1>" when
> I got there. By pressing "i", the router rebooted and came up fine.
> The output of the show ver is below. What does the error
> message mean - does
> it (PC 0x603503CC) point to a specific cause..?????
>
> ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY
> DEPLOYMENT
> RELEASE SOFTWARE (fc2)
>
> xxxxxx uptime is 48 minutes
> System returned to ROM by error - a Software forced crash, PC
> 0x603503CC
> System image file is "flash:c3640-ds-mz.121-5a.bin"
>
> cisco 3640 (R4700) processor (revision 0x00) with
> 60416K/5120K bytes of
> memory.
> Processor board ID 06014488
> R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
> Bridging software.
> X.25 software, Version 3.0.0.
> SuperLAT software (copyright 1990 by Meridian Technology Corp).
> Basic Rate ISDN software, Version 1.1.
> 2 Ethernet/IEEE 802.3 interface(s)
> 2 Token Ring/IEEE 802.5 interface(s)
> 4 Serial network interface(s)
> 8 Low-speed serial(sync/async) network interface(s)
> 4 ISDN Basic Rate interface(s)
> DRAM configuration is 64 bits wide with parity disabled.
> 125K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
> Configuration register is 0x2102
>
>
> Thanks
> Andrew Larkins
> BCom, CCNA, CCDA
> Bytes Technology Group
> Tel: +2711 800-9300
> Fax: +2711 800-9496
> Cell: +2783-656-7214
> Email: [EMAIL PROTECTED]
> OR [EMAIL PROTECTED]
>
>
> "This message may contain information which is confidential
> and subject to
> legal privilege. If you are not the intended recipient, you
> may not peruse,
> use, disseminate, distribute or copy this message. If you
> have received
> this message in error, please notify the sender immediately by email,
> facsimile or telephone and return and/or destroy the original
> message."
>
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
