Windows NT can issue break sequence accoruding to the following document
provided from cisco.
http://www.cisco.com/warp/public/701/61.html
Please correct me if I am wrong. I did not try it.
""Stuart Potts"" <[EMAIL PROTECTED]> ¼¶¼g©ó¶l¥ó
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi Guys
>
> Windows 2000 employs power management, and this can cause problems,
disable.
>
> Windows NT you cannot issue the break sequence, solution is to drop the
baud
> rate to 2400 or so, save the configuration, reload router, while booting
> (within 30seconds) change baud rate back to 9600 holding down space.
>
> Other than that as Cyndi mentioned use another term application.
>
> /Stuart
>
>
> -------------------------------------------------------------------------
>
> | | Stuart Potts
> ||| ||| Customer Support Engineer
> .|||||. .|||||.
> .:|||||||||:.:|||||||||:.
> c i s c o S y s t e m s Email: [EMAIL PROTECTED]
>
> "Empowering the Internet Generation"
> -------------------------------------------------------------------------
>
>
>
> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> Garrison, Cyndi D.
> Sent: Tuesday, March 06, 2001 2:17 PM
> To: 'Navin Parwal'; [EMAIL PROTECTED]
> Subject: RE: Cisco Configuration Help
>
>
>
> I have found that one of the more currnet versions of hyperterminal will
not
> work with the console of some of the cisco routers. I have not figured
out
> whether it is the IOS or just the hyperterminal. Try upgrading your
> hyperterminal program or using another program. If that is not possible
try
> a another desktop or laptop with Windows NT or 98. I have windows 2000
and
> have run into the same problem.
>
> Cyndi Garrison
>
> -----Original Message-----
> From: Navin Parwal [mailto:[EMAIL PROTECTED]]
> Sent: Tuesday, March 06, 2001 7:23 AM
> To: [EMAIL PROTECTED]
> Subject: Cisco Configuration Help
>
>
> Hello Everyone ,
> I am new on Cisco routers and Switches , I am facing a problem
on
> a new Cisco router 2610 which my company has purchased .
> I am able to telnet on to that router via other router , but I am not
> able to configure with the console port , as soon as i start it with the
> console port , it starts , displays the welcome message and then it shows
> the status of the iinterfaces which has come up , but it does not come to
> the user mode , ie cisco> prompt .
> When I telnet it from the other router I am able to log in giving the
> telnet password and I am able to configure it then but I am not able to
get
> the prompt from my console which is on Windows Millemium , could anyone
> guide me why this error is coming and how I may correct it .
>
> thanks in advance,
>
> Navin Parwal
>
>
>
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
>
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
