Hey- it's a 2500 (config-reg). Confreg comes in when you spend more money :o) Phil ----- Original Message ----- From: "Snow Jr., Jim" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Thursday, March 15, 2001 11:47 AM Subject: RE: 2523 > There is a manual "break" as well.... Put a break-out box between the > terminal and the console port and tie pin 2 (TD) high for five seconds > during boot-up. This will kick you instantly into rommon where you can > change the confreg settings.... > > Jim Snow, CCNA > Project Support Engineer > [EMAIL PROTECTED] > > HQ US Central Command > CCJ2-Requirements, Bldg 540 > MacDill AFB, Florida 33621 > (813) 827-6049 > GENERAL DYNAMICS > WORLDWIDE TELECOMMUNICATION SYSTEMS > > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Tim O'Brien > Sent: Wednesday, March 14, 2001 9:06 PM > To: Circusnuts; Stull, Cory; [EMAIL PROTECTED] > Subject: Re: 2523 > > > The config reg setting of 0x3920 is the Console port set to 115200,8,N,1. > You can either set your Hyperterm to the previously mentioned settings or > telnet in and force the speed of the "line con 0" to 9600.... > > > Tim > > ----- Original Message ----- > From: "Circusnuts" <[EMAIL PROTECTED]> > To: "Stull, Cory" <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > Sent: Wednesday, March 14, 2001 5:35 PM > Subject: Re: 2523 > > > I have no idea why or what you have done (0x3920 :-) The only superior > BREAK command I know is to lower Hyper Term to 1200 (reset the Hyper Term > window) & power the router off/on. Hold the space bar for 5 seconds while > powering the router on, you should see some garble in the top left of the > screen (may have to do this a couple of times for it to take). This sends > the manual BREAK signal that commands sometimes do not. Lastly- change > everything back. Other than the above, call the TAC or pull the FLASH so it > will only boot to ROM (then change your config values back to 0x2102 or o/r > 0x42). > > Let us know how you make out !!! > Phil > > ----- Original Message ----- > From: "Stull, Cory" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Wednesday, March 14, 2001 11:03 PM > Subject: 2523 > > > > We've got a 2523 in the office that we changed the config-reg settings to > > 0x3920 and it now won't let us into it at all... We've tried to > ctrl-break > > out during boot and its not helping... > > > > Any other suggestions? > > > > Thanks > > > > _________________________________ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _________________________________ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _________________________________ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _________________________________ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _________________________________ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
