Hi all,
I am trying to dial ISP by using modem analog in cisco 805 (connected to
serial port). I already use Fast step and Config maker but yield no result.
I only able to dial in, the modem get disconnected a few minutes after
dialin established. I put some debugging message below in case anybody has
the same problem as I am or maybe know how to solve it. Thanks much.
Andri
cisco805#
01:51:36: Serial0 DDR: rotor dialout [priority]
01:51:36: Serial0 DDR: Dialing cause ip (s=192.168.2.1, d=202.148.11.40)
01:51:36: Serial0 DDR: Attempting to dial 21,5550019
01:51:36: CHAT1: Attempting async line dialer script
01:51:36: CHAT1: Dialing using Modem script: dial & System script: none
01:51:36: CHAT1: process started
01:51:36: CHAT1: Asserting DTR
01:51:36: CHAT1: Chat script dial started
cisco805#
01:51:56: CHAT1: Chat script dial finished, status = Success
01:51:57: TTY1: destroy timer type 1
01:51:57: TTY1: destroy timer type 0
01:51:59: %LINK-3-UPDOWN: Interface Serial0, changed state to upDialer
statecha0
01:51:59: %DIALER-6-BIND: Interface Serial0 bound to profile Dialer1Dialer
call0
01:51:59: Se0 PPP: Treating connection as a callout
01:51:59: Se0 PPP: Phase is ESTABLISHING, Active Open
01:51:59: Se0 PPP: No remote authentication for call-out
01:51:59: Se0 LCP: O CONFREQ [Closed] id 12 len 20
01:51:59: Se0 LCP: ACCM 0x000A0000 (0x0206000A0000)
01:51:59: Se0 LCP: MagicNumber 0x01FCF6EF (0x050601FCF6EF)
01:51:59: Se0 LCP: PFC (0x0702)
01:51:59: Se0 LCP: ACFC (0x0802)
01:52:01: Se0 LCP: TIMEout: State REQsent
01:52:01: Se0 LCP: O CONFREQ [REQsent] id 13 len 20
01:52:01: Se0 LCP: ACCM 0x000A0000 (0x0206000A0000)
01:52:01: Se0 LCP: MagicNumber 0x01FCF6EF (0x050601FCF6EF)
01:52:01: Se0 LCP: PFC (0x0702)
01:52:01: Se0 LCP: ACFC (0x0802)
01:52:03: Se0 LCP: TIMEout: State REQsent
01:52:03: Se0 LCP: O CONFREQ [REQsent] id 14 len 20
01:52:03: Se0 LCP: ACCM 0x000A0000 (0x0206000A0000)
01:52:03: Se0 LCP: MagicNumber 0x01FCF6EF (0x050601FCF6EF)
01:52:03: Se0 LCP: PFC (0x0702)
01:52:03: Se0 LCP: ACFC (0x0802)
---------------
01:52:17: Se0 LCP: MagicNumber 0x01FCF6EF (0x050601FCF6EF)
01:52:17: Se0 LCP: PFC (0x0702)
01:52:17: Se0 LCP: ACFC (0x0802)
01:52:19: Se0 LCP: TIMEout: State REQsent
01:52:19: Se0 LCP: O CONFREQ [REQsent] id 22 len 20
01:52:19: Se0 LCP: ACCM 0x000A0000 (0x0206000A0000)
01:52:19: Se0 LCP: MagicNumber 0x01FCF6EF (0x050601FCF6EF)
01:52:19: Se0 LCP: PFC (0x0702)
01:52:19: Se0 LCP: ACFC (0x0802)
01:52:21: Se0 LCP: TIMEout: State REQsent
01:52:21: TTY1: Async Int reset: Dropping DTR
01:52:21: Se0 LCP: State is Listen
01:52:23: TTY1: DSR was dropped
01:52:23: tty1: Modem: READY->(unknown)
01:52:23: %LINK-5-CHANGED: Interface Serial0, changed state to reset
01:52:23: Se0 DDR: has total 1 call(s), dial_out 0, dial_in 0
01:52:23: Calling lineaction of Serial0
01:52:23: Se0 LCP: State is Closed
01:52:23: Se0 PPP: Phase is DOWN
01:52:23: %DIALER-6-UNBIND: Interface Serial0 unbound from profile Dialer1
01:52:23: Se0 LCP: State is Closed
01:52:23: Se0 PPP: Phase is DOWN
01:52:24: TTY1: dropping DTR, hanging up
01:52:24: tty1: Modem: HANGUP->(unknown)
01:52:25: TTY1: cleanup pending. Delaying DTR
01:52:26: TTY1: cleanup pending. Delaying DTR
01:52:26: TTY1: destroy timer type 0
01:52:26: TTY1: destroy timer type 1
01:52:26: TTY1: destroy timer type 3
01:52:26: TTY1: destroy timer type 4
01:52:26: TTY1: destroy timer type 2
01:52:26: Serial0: allowing modem_process to continue hangup
01:52:28: TTY1: restoring DTR
01:52:28: %LINK-3-UPDOWN: Interface Serial0, changed state to down
01:52:28: Se0 LCP: State is Closed
01:52:28: Se0 PPP: Phase is DOWN
: Serial0 DDR: re-enable timeout
cisco805#
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
