You didn't BREAK soon enough... Power off & hit Cntrl Break within a few
seconds & you should see > If this does not work, lower your terminal speed
to 1200 (restart the terminal window) power off the router/ back on, then
hold the space bar for about 5 seconds. You should see garble @ the top
left. You might have to do this more than once. Return you terminal speed
to 9600 (restart the terminal window) & you should see the >
Phil
----- Original Message -----
From:
To:
Sent: Thursday, April 12, 2001 6:32 PM
Subject: Password recovery [7:415]
> I was trying to do a password recovery on a 2503 router, after pressing
> Break....here is what I got on the attachment.
>
> Looks like its crashed, cann't type and its not going.
>
> Please assist!!!
>
> System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> Copyright (c) 1986-1995 by cisco Systems
> 2500 processor with 16384 Kbytes of main memory
> F3: 4442848+146464+241348 at 0x1000
>
> Restricted Rights Legend
>
> Use, duplication, or disclosure by the Government is
> subject to restrictions as set forth in subparagraph
> (c) of the Commercial Computer Software - Restricted
> Rights clause at FAR sec. 52.227-19 and subparagraph
> (c) (1) (ii) of the Rights in Technical Data and Computer
> Software clause at DFARS sec. 252.227-7013.
>
> cisco Systems, Inc.
> 170 West Tasman Drive
> San Jose, California 95134-1706
>
>
>
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Software (IGS-IR-L), Experimental Version 11.0(9682)
[athippes
> 109]
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Fri 15-Nov-96 16:28 by athippes
> Image text-base: 0x00001448, data-base: 0x00417FE4
>
> cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of
memory.
> Processor board ID 03863193, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> Basic Rate ISDN software, Version 1.0.
> 1 Ethernet/IEEE 802.3 interface.
> 2 Serial network interfaces.
> 1 ISDN Basic Rate interface.
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
>
>
> Press RETURN to get started!
>
>
> %LINK-3-UPDOWN: Interface BRI0, changed state to up
> %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> %LINK-3-UPDOWN: Interface Serial0, changed state to down
> %LINK-3-UPDOWN: Interface Serial1, changed state to down
> *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet0,
> changed state to up
> *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
> changed state to down
> *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
> changed state to down
> *Mar 1 00:00:10:
> Note: A random Spanning Tree Bridge Identifier address of 0000.0c00.0539
> has been chosen for Bridge group 1 since there is no mac address
> associated with the selected interface.
> *Mar 1 00:00:10:
> Ensure that this address is unique.
>
> *Mar 1 00:00:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet0,
> changed state to down
> *Mar 1 00:00:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Loopback0,
> changed state to up
> *Mar 1 00:00:13: %LINK-5-CHANGED: Interface Ethernet0, changed state to
> administratively down
> *Mar 1 00:00:13: %LINK-5-CHANGED: Interface Serial0, changed state to
> administratively down
> *Mar 1 00:00:13: %FR-5-DLCICHANGE: Interface Serial0 - DLCI 26 state
> changed to DELETED
> *Mar 1 00:00:14: %LINK-5-CHANGED: Interface BRI0, changed state to
> administratively down
> *Mar 1 00:00:14: %LINK-3-UPDOWN: Interface BRI0: B-Channel 1, changed
state
> to down
> *Mar 1 00:00:14: %LINK-3-UPDOWN: Interface BRI0: B-Channel 2, changed
state
> to down
> *Mar 1 00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0,
> changed state to down
> *Mar 1 00:00:15: %LINK-5-CHANGED: Interface Serial1, changed state to
> administratively down
> *Mar 1 00:00:18: %SYS-5-CONFIG_I: Configured from memory by console
> *Mar 1 00:00:18: %SYS-5-RESTART: System restarted --
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Software (IGS-IR-L), Experimental Version 11.0(9682)
[athippes
> 109]
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Fri 15-Nov-96 16:28 by athippes
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=424&t=415
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
