You should press "CTRL" and "Break" key right after the first 2 or 3 line of
text appear on your Hyper Terminal. You should get get a > prompt. At the
> prompt, type:
o/r 0x2141
Them type "i" at the prompt to initialize the router. This will allow you
to enter the router enable mode to reset the password. Once reset the
password, reload and doing the same thing, but set register to:
0x2102
to boot to the flash.
wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I was trying to do a password recovery on a 2503 router, after pressing
> Break....here is what I got on the attachment.
>
> Looks like its crashed, cann't type and its not going.
>
> Please assist!!!
>
> System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
> Copyright (c) 1986-1995 by cisco Systems
> 2500 processor with 16384 Kbytes of main memory
> F3: 4442848+146464+241348 at 0x1000
>
> Restricted Rights Legend
>
> Use, duplication, or disclosure by the Government is
> subject to restrictions as set forth in subparagraph
> (c) of the Commercial Computer Software - Restricted
> Rights clause at FAR sec. 52.227-19 and subparagraph
> (c) (1) (ii) of the Rights in Technical Data and Computer
> Software clause at DFARS sec. 252.227-7013.
>
> cisco Systems, Inc.
> 170 West Tasman Drive
> San Jose, California 95134-1706
>
>
>
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Software (IGS-IR-L), Experimental Version 11.0(9682)
[athippes
> 109]
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Fri 15-Nov-96 16:28 by athippes
> Image text-base: 0x00001448, data-base: 0x00417FE4
>
> cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of
memory.
> Processor board ID 03863193, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> Basic Rate ISDN software, Version 1.0.
> 1 Ethernet/IEEE 802.3 interface.
> 2 Serial network interfaces.
> 1 ISDN Basic Rate interface.
> 32K bytes of non-volatile configuration memory.
> 16384K bytes of processor board System flash (Read/Write)
>
>
>
> Press RETURN to get started!
>
>
> %LINK-3-UPDOWN: Interface BRI0, changed state to up
> %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
> %LINK-3-UPDOWN: Interface Serial0, changed state to down
> %LINK-3-UPDOWN: Interface Serial1, changed state to down
> *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet0,
> changed state to up
> *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0,
> changed state to down
> *Mar 1 00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1,
> changed state to down
> *Mar 1 00:00:10:
> Note: A random Spanning Tree Bridge Identifier address of 0000.0c00.0539
> has been chosen for Bridge group 1 since there is no mac address
> associated with the selected interface.
> *Mar 1 00:00:10:
> Ensure that this address is unique.
>
> *Mar 1 00:00:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Ethernet0,
> changed state to down
> *Mar 1 00:00:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Loopback0,
> changed state to up
> *Mar 1 00:00:13: %LINK-5-CHANGED: Interface Ethernet0, changed state to
> administratively down
> *Mar 1 00:00:13: %LINK-5-CHANGED: Interface Serial0, changed state to
> administratively down
> *Mar 1 00:00:13: %FR-5-DLCICHANGE: Interface Serial0 - DLCI 26 state
> changed to DELETED
> *Mar 1 00:00:14: %LINK-5-CHANGED: Interface BRI0, changed state to
> administratively down
> *Mar 1 00:00:14: %LINK-3-UPDOWN: Interface BRI0: B-Channel 1, changed
state
> to down
> *Mar 1 00:00:14: %LINK-3-UPDOWN: Interface BRI0: B-Channel 2, changed
state
> to down
> *Mar 1 00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0,
> changed state to down
> *Mar 1 00:00:15: %LINK-5-CHANGED: Interface Serial1, changed state to
> administratively down
> *Mar 1 00:00:18: %SYS-5-CONFIG_I: Configured from memory by console
> *Mar 1 00:00:18: %SYS-5-RESTART: System restarted --
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Software (IGS-IR-L), Experimental Version 11.0(9682)
[athippes
> 109]
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Fri 15-Nov-96 16:28 by athippes
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=434&t=415
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
