i have been through this one .
your config is fine
just check the following
the name of the remote router has to be the username and the password the
same on both
example
local router r4
username r3 pass cisco
remote router r3
username r4 pass cisco
Gaz wrote:
> Hi,
>
> Can you help me plz guys been trying to get me 1601 with ISDN WIC to work
> for yonks. From debug's it looks like CHAP AUTH is failing but I don't know
> why ?!
>
> I have enclosed sh ver, sh run and debug dialer, debug ppp auth chap.
>
> Any help would be greatly appreciated.
>
> Thanx in advance.
>
> Sh ver
>
> 1601#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 1600 Software (C1600-SY-L), Version 12.0(7)T, RELEASE SOFTWARE
> (fc2)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Mon 06-Dec-99 18:03 by phanguye
> Image text-base: 0x0803DCE8, data-base: 0x02005000
>
> ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT
> RELEASE
> SOFTWARE (fc2)
> ROM: 1600 Software (C1600-BOOT-R), Version 11.1(7)AX, EARLY DEPLOYMENT
> RELEASE S
> OFTWARE (fc2)
>
> 1601 uptime is 1 hour, 30 minutes
> System returned to ROM by power-on
> System image file is "flash:/c1600-1207T.bin"
>
> cisco 1601 (68360) processor (revision C) with 13824K/4608K bytes of
memory.
> Processor board ID 04909005, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> Basic Rate ISDN software, Version 1.1.
> 1 Ethernet/IEEE 802.3 interface(s)
> 1 Serial(sync/async) network interface(s)
> 1 ISDN Basic Rate interface(s)
> System/IO memory with parity disabled
> 2048K bytes of DRAM onboard 16384K bytes of DRAM on SIMM
> System running from FLASH
> 7K bytes of non-volatile configuration memory.
> 8192K bytes of processor board PCMCIA flash (Read ONLY)
>
> Configuration register is 0x2102
>
> Sh run
>
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug datetime msec
> service timestamps log uptime
> no service password-encryption
> service udp-small-servers
> service tcp-small-servers
> !
> hostname 1601
> !
> enable secret 5 $1$FgI.$bygzIO/R77k37T.qfBWhH.
> !
> username xxxxxx password 0 xxxxx
> !
> !
> !
> !
> ip subnet-zero
> no ip domain-lookup
> !
> isdn switch-type basic-net3
> isdn voice-call-failure 0
> !
> !
> !
> interface Ethernet0
> ip address 10.10.1.1 255.255.255.0
> no ip directed-broadcast
> ip nat inside
> no ip route-cache
> no ip mroute-cache
> !
> interface Serial0
> physical-layer async
> bandwidth 64000
> ip unnumbered Ethernet0
> no ip directed-broadcast
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> keepalive 10
> dialer in-band
> dialer wait-for-carrier-time 120
> async mode interactive
> fair-queue 64 16 0
> ppp authentication chap callin
> !
> interface BRI0
> bandwidth 64
> ip address negotiated
> no ip directed-broadcast
> ip nat outside
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> no keepalive
> dialer idle-timeout 150
> dialer string 08451400101
> dialer-group 2
> isdn switch-type basic-net3
> ppp authentication chap
> !
> ip nat inside source list 100 interface BRI0 overload
> ip classless
> ip route 0.0.0.0 0.0.0.0 BRI0
> no ip http server
> !
> access-list 100 permit ip 10.10.1.0 0.0.0.255 any
> access-list 101 deny udp any any eq snmp
> access-list 101 deny udp any any eq ntp
> access-list 101 permit ip any any
> access-list 110 deny udp 10.10.1.0 0.0.0.255 eq netbios-ns any log
> dialer-list 1 protocol ip list 110
> dialer-list 2 protocol ip permit
> !
> line con 0
> exec-timeout 0 0
> transport input none
> line 1
> modem InOut
> transport input all
> stopbits 1
> speed 115200
> flowcontrol hardware
> line vty 0
> exec-timeout 0 0
> login local
> length 25
> line vty 1 4
> exec-timeout 0 0
> login local
> !
>
> 1601#sh deb
> Dial on demand:
> Dial on demand events debugging is on
> PPP:
> PPP protocol negotiation debugging is on
> ISDN:
> ISDN Q931 packets debugging is on
> ISDN Q931 packets debug DSLs. (On/Off/No DSL:1/0/-)
> DSL 0 --> 1
> 1 -
>
> 1601#ping 4.1.1.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 4.1.1.1, timeout is 2 seconds:
>
> *Mar 1 01:42:51.533: BRI0 DDR: Dialing cause ip (s=10.10.1.1, d=4.1.1.1)
> *Mar 1 01:42:51.537: BRI0 DDR: Attempting to dial 08451400101
> *Mar 1 01:42:51.549: ISDN BR0: TX -> SETUP pd = 8 callref = 0x04
> *Mar 1 01:42:51.553: Bearer Capability i = 0x8890
> *Mar 1 01:42:51.553: Channel ID i = 0x83
> *Mar 1 01:42:51.557: Called Party Number i = 0x80, '08451400101'
> *Mar 1 01:42:51.747: ISDN BR0: RX CONNECT_ACK pd = 8 callref = 0x04
> 01:43:43: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> 01:43:43: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 08451400101
> *Mar 1 01:42:53.561: BR0:2 PPP: Treating connection as a callout
> *Mar 1 01:42:53.565: BR0:2 PPP: Phase is ESTABLISHING, Active Open
> *Mar 1 01:42:53.569: BR0:2 LCP: O CONFREQ [Closed] id 7 len 15
> *Mar 1 01:42:53.573: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.577: BR0:2 LCP: MagicNumber 0x60BBB227 (0x050660BBB227)
> *Mar 1 01:42:53.616: BR0:2 LCP: I CONFREQ [REQsent] id 178 len 28
> *Mar 1 01:42:53.620: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:53.624: BR0:2 LCP: MagicNumber 0x284CF490 (0x0506284CF490)
> *Mar 1 01:42:53.628: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:53.632: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:42:53.636: BR0:2 LCP: O CONFREJ [REQsent] id 178 len 18
> *Mar 1 01:42:53.636: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:53.640: .BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E657
> 4)
> *Mar 1 01:42:53.644: BR0:2 LCP: I CONFACK [REQsent] id 7 len 15
> *Mar 1 01:42:53.648: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.652: BR0:2 LCP: MagicNumber 0x60BBB227 (0x050660BBB227)
> *Mar 1 01:42:53.680: BR0:2 LCP: I CONFREQ [ACKrcvd] id 179 len 14
> *Mar 1 01:42:53.684: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:53.688: BR0:2 LCP: MagicNumber 0x284CF490 (0x0506284CF490)
> *Mar 1 01:42:53.692: BR0:2 LCP: O CONFNAK [ACKrcvd] id 179 len 9
> *Mar 1 01:42:53.692: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.731: BR0:2 LCP: I CONFREQ [ACKrcvd] id 180 len 15
> *Mar 1 01:42:53.735: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.739: BR0:2 LCP: MagicNumber 0x284CF490 (0x0506284CF490)
> *Mar 1 01:42:53.743: BR0:2 LCP: O CONFACK [ACKrcvd] id 180 len 15
> *Mar 1 01:42:53.743: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.747: BR0:2 LCP: MagicNumber 0x284CF490
(0x.0506284CF490)
> *Mar 1 01:42:53.751: BR0:2 LCP: State is Open
> *Mar 1 01:42:53.751: BR0:2 PPP: Phase is AUTHENTICATING, by both
> *Mar 1 01:42:53.755: BR0:2 CHAP: O CHALLENGE id 4 len 25 from "1601"
> *Mar 1 01:42:53.787: BR0:2 CHAP: I CHALLENGE id 222 len 28 from "plusnet"
> *Mar 1 01:42:53.795: BR0:2 CHAP: Username plusnet not found
> *Mar 1 01:42:53.795: BR0:2 CHAP: Unable to authenticate for peer
> *Mar 1 01:42:53.799: BR0:2 PPP: Phase is TERMINATING
> *Mar 1 01:42:53.799: BR0:2 LCP: O TERMREQ [Open] id 8 len 4
> *Mar 1 01:42:53.838: BR0:2 LCP: I TERMACK [TERMsent] id 8 len 4
> *Mar 1 01:42:53.838: BR0:2 LCP: State is Closed
> *Mar 1 01:42:53.842: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:53.842: BRI0:2 DDR: disconnecting call
> *Mar 1 01:42:53.846: BR0:2 PPP: Phase is ESTABLISHING, Passive Open
> *Mar 1 01:42:53.846: BR0:2 LCP: State is Listen
> *Mar 1 01:42:53.866: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x04
> *Mar 1 01:42:53.870: Cause i = 0x8090 - Normal call clearing
> *Mar 1 01:42:54..350: ISDN BR0: RX RELEASE_COMP pd = 8 callref = 0x04
> 01:43:44: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
> *Mar 1 01:42:54.394: BR0:2 LCP: State is Closed
> *Mar 1 01:42:54.398: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:54.398: BRI0:2 DDR: disconnecting call
> *Mar 1 01:42:55.910: BRI0 DDR: Dialing cause ip (s=10.10.1.1, d=4.1.1.1)
> *Mar 1 01:42:55.914: BRI0 DDR: Attempting to dial 08451400101
> *Mar 1 01:42:55.926: ISDN BR0: TX -> SETUP pd = 8 callref = 0x05
> *Mar 1 01:42:55.930: Bearer Capability i = 0x8890
> *Mar 1 01:42:55.933: Channel ID i = 0x83
> *Mar 1 01:42:55.933: Called Party Number i = 0x80, '08451400101'
> *Mar 1 01:42:56.124: ISDN BR0: RX CONNECT_ACK pd = 8 callref = 0x05
> 01:43:47: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> 01:43:47: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 08451400101
> *Mar 1 01:42:57.541: BR0:2 PPP: Treating connection as a callout
> *Mar 1 01:42:57.545: BR0:2 PPP: Phase is ESTABLISHING, Active Open
> *Mar 1 01:42:57.548: BR0:2 LCP: O CONFREQ [Closed] id 9 len 15
> *Mar 1 01:42:57.552: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.552: BR0:2 LCP: MagicNumber 0x60BBC1D1 (0x050660BBC1D1)
> *Mar 1 01:42:57.743: BR0:2 LCP: I CONFREQ [REQsent] id 187 len 28
> *Mar 1 01:42:57.747: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:57.751: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.751: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:57.755: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:42:57.759: BR0:2 LCP: O CONFREJ [REQsent] id 187 len 18
> *Mar 1 01:42:57.763: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:57.767: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:42:57.771: BR0:2 LCP: I CONFACK [REQsent] id 9 len 15
> *Mar 1 01:42:57.775: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.779: BR0:2 LCP: MagicNumber 0x60BBC1D1 (0x050660BBC1D1)
> *Mar 1 01:42:57.806: BR0:2 LCP: I CONFREQ [ACKrcvd] id 188 len 14
> *Mar 1 01:42:57.806: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:57.810: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.814: BR0:2 LCP: O CONFNAK [ACKrcvd] id 188 len 9
> *Mar 1 01:42:57.818: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.854: BR0:2 LCP: I CONFREQ [ACKrcvd] id 189 len 15
> *Mar 1 01:42:57.858: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.862: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.866: BR0:2 LCP: O CONFACK [ACKrcvd] id 189 len 15
> *Mar 1 01:42:57.870: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.870: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.874: BR0:2 LCP: State is Open
> *Mar 1 01:42:57.878: BR0:2 PPP: Phase is AUTHENTICATING, by both
> *Mar 1 01:42:57.882: BR0:2 CHAP: O CHALLENGE id 5 len 25 from "1601"
> *Mar 1 01:42:57.917: BR0:2 CHAP: I CHALLENGE id 188 len 28 from "plusnet"
> *Mar 1 01:42:57.921: BR0:2 CHAP: Username plusnet not found
> *Mar 1 01:42:57.921: BR0:2 CHAP: Unable to authenticate for peer
> *Mar 1 01:42:57.925: BR0:2 PPP: Phase is TERMINATING
> *Mar 1 01:42:57.929: BR0:2 LCP: O TERMREQ [Open] id 10 len 4
> *Mar 1 01:42:57.965: BR0:2 LCP: I TERMACK [TERMsent] id 10 len 4
> *Mar 1 01:42:57.965: BR0:2 LCP: State is Closed
> *Mar 1 01:42:57.969: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:57.969: BRI0:2 DDR: disconnecting call
> *Mar 1 01:42:57.973: BR0:2 PPP: Phase is ESTABLISHING, Passive Open
> *Mar 1 01:42:57.973: BR0:2 LCP: State is Listen
> *Mar 1 01:42:57.993: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x05
> *Mar 1 01:42:57.993: Cause i = 0x8090 - Normal call clearing
> *Mar 1 01:42:58.179: ISDN BR0: RX RELEASE_COMP pd = 8 callref = 0x05
> 01:43:48: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
> *Mar 1 01:42:58.219: BR0:2 LCP: State is Closed
> *Mar 1 01:42:58.223: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:58.223: BRI0:2 DDR: disconnecting call
> *Mar 1 01:43:00.647: BRI0 DDR: Dialing cause ip (s=10.10.1.1, d=4.1.1.1)
> *Mar 1 01:43:00.651: BRI0 DDR: Attempting to dial 08451400101
> *Mar 1 01:43:00.663: ISDN BR0: TX -> SETUP pd = 8 callref = 0x06
> *Mar 1 01:43:00.667: Bearer Capability i = 0x8890
> *Mar 1 01:43:00.667: Channel ID i = 0x83
> *Mar 1 01:43:00.671: Called Party Number i = 0x80, '08451400101'
> *Mar 1 01:43:00.870: ISDN BR0: RX CONNECT_ACK pd = 8 callref = 0x06
> 01:43:52: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> 01:43:52: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 08451400101
> *Mar 1 01:43:02.207: BR0:2 PPP: Treating connection as a callout
> *Mar 1 01:43:02.207: BR0:2 PPP: Phase is ESTABLISHING, Active Open
> *Mar 1 01:43:02.215: BR0:2 LCP: O CONFREQ [Closed] id 11 len 15
> *Mar 1 01:43:02.215: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.219: BR0:2 LCP: MagicNumber 0x60BBD434 (0x050660BBD434)
> *Mar 1 01:43:02.405: BR0:2 LCP: I CONFREQ [REQsent] id 173 len 28
> *Mar 1 01:43:02.409: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:43:02.409: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.413: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:43:02.417: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:43:02.421: BR0:2 LCP: O CONFREJ [REQsent] id 173 len 18
> *Mar 1 01:43:02.425: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:43:02.429: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:43:02.433: BR0:2 LCP: I CONFACK [REQsent] id 11 len 15
> *Mar 1 01:43:02.433: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.437: BR0:2 LCP: MagicNumber 0x60BBD434 (0x050660BBD434)
> *Mar 1 01:43:02.469: BR0:2 LCP: I CONFREQ [ACKrcvd] id 174 len 14
> *Mar 1 01:43:02.469: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:43:02.473: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.477: BR0:2 LCP: O CONFNAK [ACKrcvd] id 174 len 9
> *Mar 1 01:43:02.481: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.520: BR0:2 LCP: I CONFREQ [ACKrcvd] id 175 len 15
> *Mar 1 01:43:02.520: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.524: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.528: BR0:2 LCP: O CONFACK [ACKrcvd] id 175 len 15
> *Mar 1 01:43:02.532: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.536: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.536: BR0:2 LCP: State is Open
> *Mar 1 01:43:02.540: BR0:2 PPP: Phase is AUTHENTICATING, by both
> *Mar 1 01:43:02.544: BR0:2 CHAP: O CHALLENGE id 6 len 25 from "1601"
> *Mar 1 01:43:02.576: BR0:2 CHAP: I CHALLENGE id 149 len 28 from "plusnet"
> *Mar 1 01:43:02.580: BR0:2 CHAP: Username plusnet not found
> *Mar 1 01:43:02.584: BR0:2 CHAP: Unable to authenticate for peer
> *Mar 1 01:43:02.584: BR0:2 PPP: Phase is TERMINATING
> *Mar 1 01:43:02.588: BR0:2 LCP: O TERMREQ [Open] id 12 len 4
> *Mar 1 01:43:02.624: BR0:2 LCP: I TERMACK [TERMsent] id 12 len 4
> *Mar 1 01:43:02.628: BR0:2 LCP: State is Closed
> *Mar 1 01:43:02.628: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:43:02.631: BRI0:2 DDR: disconnecting call
> *Mar 1 01:43:02.631: BR0:2 PPP: Phase is ESTABLISHING, Passive Open
> *Mar 1 01:43:02.635: BR0:2 LCP: State is Listen
> *Mar 1 01:43:02.651: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x06
> *Mar 1 01:43:02.655: Cause i = 0x8090 - Normal call clearing
> *Mar 1 01:43:02.830: ISDN BR0: RX RELEASE_COMP pd = 8 callref = 0x06
> 01:43:52: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
> *Mar 1 01:43:02.874: BR0:2 LCP: State is Closed
> *Mar 1 01:43:02.874: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:43:02.877: BRI0:2 DDR: disconnecting call
> 1601#
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=18155&t=18093
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
