Hello Gaz,
I was facing a very similar issue.This is what I did and
it may seem
strange but it worked for me .I turned on service password-encryption and
then CHAP
authentication strated working .
See if it works for you
Jaspreet
Gaz wrote:
> Hi,
>
> Can you help me plz guys been trying to get me 1601 with ISDN WIC to work
> for yonks. From debug's it looks like CHAP AUTH is failing but I don't know
> why ?!
>
> I have enclosed sh ver, sh run and debug dialer, debug ppp auth chap.
>
> Any help would be greatly appreciated.
>
> Thanx in advance.
>
> Sh ver
>
> 1601#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 1600 Software (C1600-SY-L), Version 12.0(7)T, RELEASE SOFTWARE
> (fc2)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Mon 06-Dec-99 18:03 by phanguye
> Image text-base: 0x0803DCE8, data-base: 0x02005000
>
> ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT
> RELEASE
> SOFTWARE (fc2)
> ROM: 1600 Software (C1600-BOOT-R), Version 11.1(7)AX, EARLY DEPLOYMENT
> RELEASE S
> OFTWARE (fc2)
>
> 1601 uptime is 1 hour, 30 minutes
> System returned to ROM by power-on
> System image file is "flash:/c1600-1207T.bin"
>
> cisco 1601 (68360) processor (revision C) with 13824K/4608K bytes of
memory.
> Processor board ID 04909005, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 3.0.0.
> Basic Rate ISDN software, Version 1.1.
> 1 Ethernet/IEEE 802.3 interface(s)
> 1 Serial(sync/async) network interface(s)
> 1 ISDN Basic Rate interface(s)
> System/IO memory with parity disabled
> 2048K bytes of DRAM onboard 16384K bytes of DRAM on SIMM
> System running from FLASH
> 7K bytes of non-volatile configuration memory.
> 8192K bytes of processor board PCMCIA flash (Read ONLY)
>
> Configuration register is 0x2102
>
> Sh run
>
> Building configuration...
>
> Current configuration:
> !
> version 12.0
> service timestamps debug datetime msec
> service timestamps log uptime
> no service password-encryption
> service udp-small-servers
> service tcp-small-servers
> !
> hostname 1601
> !
> enable secret 5 $1$FgI.$bygzIO/R77k37T.qfBWhH.
> !
> username xxxxxx password 0 xxxxx
> !
> !
> !
> !
> ip subnet-zero
> no ip domain-lookup
> !
> isdn switch-type basic-net3
> isdn voice-call-failure 0
> !
> !
> !
> interface Ethernet0
> ip address 10.10.1.1 255.255.255.0
> no ip directed-broadcast
> ip nat inside
> no ip route-cache
> no ip mroute-cache
> !
> interface Serial0
> physical-layer async
> bandwidth 64000
> ip unnumbered Ethernet0
> no ip directed-broadcast
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> keepalive 10
> dialer in-band
> dialer wait-for-carrier-time 120
> async mode interactive
> fair-queue 64 16 0
> ppp authentication chap callin
> !
> interface BRI0
> bandwidth 64
> ip address negotiated
> no ip directed-broadcast
> ip nat outside
> encapsulation ppp
> no ip route-cache
> no ip mroute-cache
> no keepalive
> dialer idle-timeout 150
> dialer string 08451400101
> dialer-group 2
> isdn switch-type basic-net3
> ppp authentication chap
> !
> ip nat inside source list 100 interface BRI0 overload
> ip classless
> ip route 0.0.0.0 0.0.0.0 BRI0
> no ip http server
> !
> access-list 100 permit ip 10.10.1.0 0.0.0.255 any
> access-list 101 deny udp any any eq snmp
> access-list 101 deny udp any any eq ntp
> access-list 101 permit ip any any
> access-list 110 deny udp 10.10.1.0 0.0.0.255 eq netbios-ns any log
> dialer-list 1 protocol ip list 110
> dialer-list 2 protocol ip permit
> !
> line con 0
> exec-timeout 0 0
> transport input none
> line 1
> modem InOut
> transport input all
> stopbits 1
> speed 115200
> flowcontrol hardware
> line vty 0
> exec-timeout 0 0
> login local
> length 25
> line vty 1 4
> exec-timeout 0 0
> login local
> !
>
> 1601#sh deb
> Dial on demand:
> Dial on demand events debugging is on
> PPP:
> PPP protocol negotiation debugging is on
> ISDN:
> ISDN Q931 packets debugging is on
> ISDN Q931 packets debug DSLs. (On/Off/No DSL:1/0/-)
> DSL 0 --> 1
> 1 -
>
> 1601#ping 4.1.1.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 4.1.1.1, timeout is 2 seconds:
>
> *Mar 1 01:42:51.533: BRI0 DDR: Dialing cause ip (s=10.10.1.1, d=4.1.1.1)
> *Mar 1 01:42:51.537: BRI0 DDR: Attempting to dial 08451400101
> *Mar 1 01:42:51.549: ISDN BR0: TX -> SETUP pd = 8 callref = 0x04
> *Mar 1 01:42:51.553: Bearer Capability i = 0x8890
> *Mar 1 01:42:51.553: Channel ID i = 0x83
> *Mar 1 01:42:51.557: Called Party Number i = 0x80, '08451400101'
> *Mar 1 01:42:51.747: ISDN BR0: RX CONNECT_ACK pd = 8 callref = 0x04
> 01:43:43: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> 01:43:43: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 08451400101
> *Mar 1 01:42:53.561: BR0:2 PPP: Treating connection as a callout
> *Mar 1 01:42:53.565: BR0:2 PPP: Phase is ESTABLISHING, Active Open
> *Mar 1 01:42:53.569: BR0:2 LCP: O CONFREQ [Closed] id 7 len 15
> *Mar 1 01:42:53.573: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.577: BR0:2 LCP: MagicNumber 0x60BBB227 (0x050660BBB227)
> *Mar 1 01:42:53.616: BR0:2 LCP: I CONFREQ [REQsent] id 178 len 28
> *Mar 1 01:42:53.620: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:53.624: BR0:2 LCP: MagicNumber 0x284CF490 (0x0506284CF490)
> *Mar 1 01:42:53.628: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:53.632: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:42:53.636: BR0:2 LCP: O CONFREJ [REQsent] id 178 len 18
> *Mar 1 01:42:53.636: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:53.640: .BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E657
> 4)
> *Mar 1 01:42:53.644: BR0:2 LCP: I CONFACK [REQsent] id 7 len 15
> *Mar 1 01:42:53.648: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.652: BR0:2 LCP: MagicNumber 0x60BBB227 (0x050660BBB227)
> *Mar 1 01:42:53.680: BR0:2 LCP: I CONFREQ [ACKrcvd] id 179 len 14
> *Mar 1 01:42:53.684: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:53.688: BR0:2 LCP: MagicNumber 0x284CF490 (0x0506284CF490)
> *Mar 1 01:42:53.692: BR0:2 LCP: O CONFNAK [ACKrcvd] id 179 len 9
> *Mar 1 01:42:53.692: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.731: BR0:2 LCP: I CONFREQ [ACKrcvd] id 180 len 15
> *Mar 1 01:42:53.735: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.739: BR0:2 LCP: MagicNumber 0x284CF490 (0x0506284CF490)
> *Mar 1 01:42:53.743: BR0:2 LCP: O CONFACK [ACKrcvd] id 180 len 15
> *Mar 1 01:42:53.743: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:53.747: BR0:2 LCP: MagicNumber 0x284CF490
(0x.0506284CF490)
> *Mar 1 01:42:53.751: BR0:2 LCP: State is Open
> *Mar 1 01:42:53.751: BR0:2 PPP: Phase is AUTHENTICATING, by both
> *Mar 1 01:42:53.755: BR0:2 CHAP: O CHALLENGE id 4 len 25 from "1601"
> *Mar 1 01:42:53.787: BR0:2 CHAP: I CHALLENGE id 222 len 28 from "plusnet"
> *Mar 1 01:42:53.795: BR0:2 CHAP: Username plusnet not found
> *Mar 1 01:42:53.795: BR0:2 CHAP: Unable to authenticate for peer
> *Mar 1 01:42:53.799: BR0:2 PPP: Phase is TERMINATING
> *Mar 1 01:42:53.799: BR0:2 LCP: O TERMREQ [Open] id 8 len 4
> *Mar 1 01:42:53.838: BR0:2 LCP: I TERMACK [TERMsent] id 8 len 4
> *Mar 1 01:42:53.838: BR0:2 LCP: State is Closed
> *Mar 1 01:42:53.842: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:53.842: BRI0:2 DDR: disconnecting call
> *Mar 1 01:42:53.846: BR0:2 PPP: Phase is ESTABLISHING, Passive Open
> *Mar 1 01:42:53.846: BR0:2 LCP: State is Listen
> *Mar 1 01:42:53.866: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x04
> *Mar 1 01:42:53.870: Cause i = 0x8090 - Normal call clearing
> *Mar 1 01:42:54..350: ISDN BR0: RX RELEASE_COMP pd = 8 callref = 0x04
> 01:43:44: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
> *Mar 1 01:42:54.394: BR0:2 LCP: State is Closed
> *Mar 1 01:42:54.398: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:54.398: BRI0:2 DDR: disconnecting call
> *Mar 1 01:42:55.910: BRI0 DDR: Dialing cause ip (s=10.10.1.1, d=4.1.1.1)
> *Mar 1 01:42:55.914: BRI0 DDR: Attempting to dial 08451400101
> *Mar 1 01:42:55.926: ISDN BR0: TX -> SETUP pd = 8 callref = 0x05
> *Mar 1 01:42:55.930: Bearer Capability i = 0x8890
> *Mar 1 01:42:55.933: Channel ID i = 0x83
> *Mar 1 01:42:55.933: Called Party Number i = 0x80, '08451400101'
> *Mar 1 01:42:56.124: ISDN BR0: RX CONNECT_ACK pd = 8 callref = 0x05
> 01:43:47: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> 01:43:47: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 08451400101
> *Mar 1 01:42:57.541: BR0:2 PPP: Treating connection as a callout
> *Mar 1 01:42:57.545: BR0:2 PPP: Phase is ESTABLISHING, Active Open
> *Mar 1 01:42:57.548: BR0:2 LCP: O CONFREQ [Closed] id 9 len 15
> *Mar 1 01:42:57.552: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.552: BR0:2 LCP: MagicNumber 0x60BBC1D1 (0x050660BBC1D1)
> *Mar 1 01:42:57.743: BR0:2 LCP: I CONFREQ [REQsent] id 187 len 28
> *Mar 1 01:42:57.747: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:57.751: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.751: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:57.755: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:42:57.759: BR0:2 LCP: O CONFREJ [REQsent] id 187 len 18
> *Mar 1 01:42:57.763: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:42:57.767: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:42:57.771: BR0:2 LCP: I CONFACK [REQsent] id 9 len 15
> *Mar 1 01:42:57.775: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.779: BR0:2 LCP: MagicNumber 0x60BBC1D1 (0x050660BBC1D1)
> *Mar 1 01:42:57.806: BR0:2 LCP: I CONFREQ [ACKrcvd] id 188 len 14
> *Mar 1 01:42:57.806: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:42:57.810: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.814: BR0:2 LCP: O CONFNAK [ACKrcvd] id 188 len 9
> *Mar 1 01:42:57.818: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.854: BR0:2 LCP: I CONFREQ [ACKrcvd] id 189 len 15
> *Mar 1 01:42:57.858: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.862: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.866: BR0:2 LCP: O CONFACK [ACKrcvd] id 189 len 15
> *Mar 1 01:42:57.870: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:42:57.870: BR0:2 LCP: MagicNumber 0x284D04BB (0x0506284D04BB)
> *Mar 1 01:42:57.874: BR0:2 LCP: State is Open
> *Mar 1 01:42:57.878: BR0:2 PPP: Phase is AUTHENTICATING, by both
> *Mar 1 01:42:57.882: BR0:2 CHAP: O CHALLENGE id 5 len 25 from "1601"
> *Mar 1 01:42:57.917: BR0:2 CHAP: I CHALLENGE id 188 len 28 from "plusnet"
> *Mar 1 01:42:57.921: BR0:2 CHAP: Username plusnet not found
> *Mar 1 01:42:57.921: BR0:2 CHAP: Unable to authenticate for peer
> *Mar 1 01:42:57.925: BR0:2 PPP: Phase is TERMINATING
> *Mar 1 01:42:57.929: BR0:2 LCP: O TERMREQ [Open] id 10 len 4
> *Mar 1 01:42:57.965: BR0:2 LCP: I TERMACK [TERMsent] id 10 len 4
> *Mar 1 01:42:57.965: BR0:2 LCP: State is Closed
> *Mar 1 01:42:57.969: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:57.969: BRI0:2 DDR: disconnecting call
> *Mar 1 01:42:57.973: BR0:2 PPP: Phase is ESTABLISHING, Passive Open
> *Mar 1 01:42:57.973: BR0:2 LCP: State is Listen
> *Mar 1 01:42:57.993: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x05
> *Mar 1 01:42:57.993: Cause i = 0x8090 - Normal call clearing
> *Mar 1 01:42:58.179: ISDN BR0: RX RELEASE_COMP pd = 8 callref = 0x05
> 01:43:48: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
> *Mar 1 01:42:58.219: BR0:2 LCP: State is Closed
> *Mar 1 01:42:58.223: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:42:58.223: BRI0:2 DDR: disconnecting call
> *Mar 1 01:43:00.647: BRI0 DDR: Dialing cause ip (s=10.10.1.1, d=4.1.1.1)
> *Mar 1 01:43:00.651: BRI0 DDR: Attempting to dial 08451400101
> *Mar 1 01:43:00.663: ISDN BR0: TX -> SETUP pd = 8 callref = 0x06
> *Mar 1 01:43:00.667: Bearer Capability i = 0x8890
> *Mar 1 01:43:00.667: Channel ID i = 0x83
> *Mar 1 01:43:00.671: Called Party Number i = 0x80, '08451400101'
> *Mar 1 01:43:00.870: ISDN BR0: RX CONNECT_ACK pd = 8 callref = 0x06
> 01:43:52: %LINK-3-UPDOWN: Interface BRI0:2, changed state to up
> 01:43:52: %ISDN-6-CONNECT: Interface BRI0:2 is now connected to 08451400101
> *Mar 1 01:43:02.207: BR0:2 PPP: Treating connection as a callout
> *Mar 1 01:43:02.207: BR0:2 PPP: Phase is ESTABLISHING, Active Open
> *Mar 1 01:43:02.215: BR0:2 LCP: O CONFREQ [Closed] id 11 len 15
> *Mar 1 01:43:02.215: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.219: BR0:2 LCP: MagicNumber 0x60BBD434 (0x050660BBD434)
> *Mar 1 01:43:02.405: BR0:2 LCP: I CONFREQ [REQsent] id 173 len 28
> *Mar 1 01:43:02.409: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:43:02.409: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.413: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:43:02.417: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:43:02.421: BR0:2 LCP: O CONFREJ [REQsent] id 173 len 18
> *Mar 1 01:43:02.425: BR0:2 LCP: MRRU 1524 (0x110405F4)
> *Mar 1 01:43:02.429: BR0:2 LCP: EndpointDisc 1 Local
> (0x130A01706C75736E6574
> )
> *Mar 1 01:43:02.433: BR0:2 LCP: I CONFACK [REQsent] id 11 len 15
> *Mar 1 01:43:02.433: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.437: BR0:2 LCP: MagicNumber 0x60BBD434 (0x050660BBD434)
> *Mar 1 01:43:02.469: BR0:2 LCP: I CONFREQ [ACKrcvd] id 174 len 14
> *Mar 1 01:43:02.469: BR0:2 LCP: AuthProto PAP (0x0304C023)
> *Mar 1 01:43:02.473: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.477: BR0:2 LCP: O CONFNAK [ACKrcvd] id 174 len 9
> *Mar 1 01:43:02.481: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.520: BR0:2 LCP: I CONFREQ [ACKrcvd] id 175 len 15
> *Mar 1 01:43:02.520: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.524: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.528: BR0:2 LCP: O CONFACK [ACKrcvd] id 175 len 15
> *Mar 1 01:43:02.532: BR0:2 LCP: AuthProto CHAP (0x0305C22305)
> *Mar 1 01:43:02.536: BR0:2 LCP: MagicNumber 0xA1BB18A2 (0x0506A1BB18A2)
> *Mar 1 01:43:02.536: BR0:2 LCP: State is Open
> *Mar 1 01:43:02.540: BR0:2 PPP: Phase is AUTHENTICATING, by both
> *Mar 1 01:43:02.544: BR0:2 CHAP: O CHALLENGE id 6 len 25 from "1601"
> *Mar 1 01:43:02.576: BR0:2 CHAP: I CHALLENGE id 149 len 28 from "plusnet"
> *Mar 1 01:43:02.580: BR0:2 CHAP: Username plusnet not found
> *Mar 1 01:43:02.584: BR0:2 CHAP: Unable to authenticate for peer
> *Mar 1 01:43:02.584: BR0:2 PPP: Phase is TERMINATING
> *Mar 1 01:43:02.588: BR0:2 LCP: O TERMREQ [Open] id 12 len 4
> *Mar 1 01:43:02.624: BR0:2 LCP: I TERMACK [TERMsent] id 12 len 4
> *Mar 1 01:43:02.628: BR0:2 LCP: State is Closed
> *Mar 1 01:43:02.628: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:43:02.631: BRI0:2 DDR: disconnecting call
> *Mar 1 01:43:02.631: BR0:2 PPP: Phase is ESTABLISHING, Passive Open
> *Mar 1 01:43:02.635: BR0:2 LCP: State is Listen
> *Mar 1 01:43:02.651: ISDN BR0: TX -> DISCONNECT pd = 8 callref = 0x06
> *Mar 1 01:43:02.655: Cause i = 0x8090 - Normal call clearing
> *Mar 1 01:43:02.830: ISDN BR0: RX RELEASE_COMP pd = 8 callref = 0x06
> 01:43:52: %LINK-3-UPDOWN: Interface BRI0:2, changed state to down
> *Mar 1 01:43:02.874: BR0:2 LCP: State is Closed
> *Mar 1 01:43:02.874: BR0:2 PPP: Phase is DOWN
> *Mar 1 01:43:02.877: BRI0:2 DDR: disconnecting call
> 1601#
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=19648&t=18093
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]