Thanks for the replies. The two MAC addresses would come from the two PC's in an office. The would both connect in to a hub and then the hub would uplink to the cisco switch. I need one pc in VLAN1 and one pc in VLAN2, from what you and Dennis stated this will not work. I appreciate the comments though.
Collin ""Leigh Anne Chisholm"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Actually, that's not correct. The original specification for VLANs from > what I understand mandates that only one VLAN can be assigned to a port, but > manufacturers such as 3COM decided to do otherwise and support multiple > VLANs per port. Cisco responded by creating (on certain switches such as > the Catalyst 2900XL) an administrator to configure a port to be a member of > more than one VLAN at a time when using a membership mode known as > "Multi-VLAN". A Multi-VLAN port can belong to up to 250 VLANs; the actual > number of VLANs to which the port can belong depends on the capability of > the switch itself. Although the concept is similar, this membership mode is > different than "trunking". The caveat to this feature is that the > Multi-VLAN membership mode cannot be configured on a switch if one or more > ports on the switch have been configured to trunk. > > For more information on this feature, search Cisco's website using the > keyword phrase "switchport multi". > > As for answering NetEng's question--I can't quite determine where multiple > MAC addresses share the same switch port. Could you identify which switch > that is? > > > -- Leigh Anne > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > Dennis > > Sent: Tuesday, October 23, 2001 3:48 PM > > To: [EMAIL PROTECTED] > > Subject: Re: MAC address and VLANs [7:23950] > > > > > > Cisco will recognize multiple macs on a single port but they must > > all be in > > the same vlan. Vlan assignment is per port. Your other option > > would be to > > replace the non cisco hub with a cisco switch which is trunked to the main > > switch. > > > > -- > > > > -=Repy to group only... no personal=- > > > > ""NetEng"" wrote in message > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > Here's my situtation. I have a corporate PC with an IP address of > > 10.10.x.x > > > and in the same office (and same physical network) another > > device with an > > IP > > > address of 192.168.100.x Both devices are connected to a small > > hub/switch > > > which in turn is connected to a cisco switch. Can I have the > > 10.10.x.x be > > > apart of one vlan and the 192.168.100.x be a member of another or the > > > default vlan? Can cisco switches recognize multiple MAC addresses on a > > > single switch port (if so, how many?) and be smart enough to know which > > vlan > > > which MAC address belongs to? This would save me hours (otherwise I have > > to > > > run cable for connections to our corporate network and > > connections to our > > > test network in every cube :-( ). TIA > > > > > > PS I understand the best way to do this would be to connect each device > > into > > > the cisco switch, but I only have a single cable run to each cube/office > > > > > > > > > (corporate pc)10.10.x.x > > > | > > > PC PC (test network) 192.168.100.x > > > | | > > > \ / > > > \ / > > > SWITCH/HUB (non-cisco) > > > | > > > | > > > CISCO SWITCH > > > VLANs > > > -------- ---------- > > > | | | | > > > | corp | | test | > > > -------- ----------- Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24011&t=23950 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]