I never indicated that you didn't have a default-metric statment
on the ASBR (Router C for IGRP process)!
My first thought was maybe you mistakenly crossed the cables
btw routers A & B, based on the configs you posted and the
diagram you wrote out!
Second:
Your routing table entries for routers A, B, and C match
what I have on my pod!
But....
You're definitely missing the 192.168.1.x network in RouterD's
routing table and that's the reason you can't ping from D to B.
Which would point to something wrong at the ASBR (RouterC)!
Here's what RouterD's routing table should look like!
RouterD#sh ip route
Gateway of last resort is not set
I 10.0.0.0/8 [100/8576] via 192.168.2.49, 00:00:56, Serial0
I 192.168.1.0/24 [100/10476] via 192.168.2.49, 00:00:56, Serial0
192.168.2.0/28 is subnetted, 1 subnets
C 192.168.2.48 is directly connected, Serial0
BTW: What's the static route on RouterC for?
I've had total reachability success both with and without the static
route on RouterC and to be honest, in my limited experience I've
only seen static routes to Null0 used to "fool" a BGP process or to
setup a route to a blackhole of sorts to drop packets. I'm sure their
may be other reasons and uses available, and ifso someone here will
clue me in!
Stefan
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Hunt Lee
Sent: Friday, December 07, 2001 8:09 PM
To: [EMAIL PROTECTED]
Subject: Re: Redistribution Question [7:28374]
And from Router D, I can ping back to A, but not to B:
RouterD#ping 10.1.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.100, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 84/86/88 ms
RouterD#ping 192.168.1.17
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.17, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
RouterD#
""Hunt Lee"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I already had the default-metric statment on the ASBR (Router C for IGRP
> process), I tried to add this to Router D (IGRP process), with no help.
> These are the routing table outputs and trace routes outputs from the
> routers:
>
> Any ideas??
>
> Thanks.
> Hunt
>
>
> RouterA#show ip route
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate
> default
>
> Gateway of last resort is not set
>
> 10.0.0.0 255.255.255.0 is subnetted, 1 subnets
> C 10.1.1.0 is directly connected, Serial1
> 192.168.1.0 255.255.255.240 is subnetted, 1 subnets
> O IA 192.168.1.16 [110/128] via 10.1.1.1, 00:07:03, Serial1
> 192.168.2.0 255.255.255.240 is subnetted, 1 subnets
> O E2 192.168.2.48 [110/20] via 10.1.1.1, 00:07:03, Serial1
> RouterA#
>
>
> RouterB#show ip route
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate
> default
>
> Gateway of last resort is not set
>
> 10.0.0.0 255.255.255.0 is subnetted, 1 subnets
> C 10.1.1.0 is directly connected, Serial1
> 192.168.1.0 255.255.255.240 is subnetted, 1 subnets
> C 192.168.1.16 is directly connected, Serial0
> 192.168.2.0 255.255.255.240 is subnetted, 1 subnets
> O E2 192.168.2.48 [110/20] via 192.168.1.18, 00:07:45, Serial0
> RouterB#
>
>
> RouterC#show ip route
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate
> default
> U - per-user static route, o - ODR
>
> Gateway of last resort is not set
>
> 10.0.0.0/24 is subnetted, 1 subnets
> O IA 10.1.1.0 [110/128] via 192.168.1.17, 00:09:58, Serial0
> 192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
> S 192.168.1.0/24 is directly connected, Null0
> C 192.168.1.16/28 is directly connected, Serial0
> 192.168.2.0/28 is subnetted, 1 subnets
> C 192.168.2.48 is directly connected, Serial1
> RouterC#
>
> RouterD#show ip route
> Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
> D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
> N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
> E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
> i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter
> area
> * - candidate default, U - per-user static route, o - ODR
> P - periodic downloaded static route
>
> Gateway of last resort is not set
>
> I 10.0.0.0/8 [100/8576] via 192.168.2.49, 00:00:58, Serial0
> 192.168.2.0/28 is subnetted, 1 subnets
> C 192.168.2.48 is directly connected, Serial0
> RouterD#
>
>
> And when I ping from Router A to D, it works.. but it doesn't work from B
to
> D (& vice versa)
>
> RouterA#ping 192.168.2.50
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.168.2.50, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 84/86/88 ms
> RouterA#
>
> RouterB#ping 192.168.2.50
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 192.168.2.50, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
> RouterB#
>
>
> And here's what I got from OSPF topology table:
>
> RouterA#show ip ospf database
>
> OSPF Router with ID (10.1.1.100) (Process ID 100)
>
>
> Router Link States (Area 1)
>
> Link ID ADV Router Age Seq# Checksum Link count
> 10.1.1.100 10.1.1.100 878 0x80000004 0x4E4 2
> 192.168.1.17 192.168.1.17 822 0x8000000F 0xEE46 2
>
> Summary Net Link States (Area 1)
>
> Link ID ADV Router Age Seq# Checksum
> 192.168.1.16 192.168.1.17 812 0x80000001 0xBC79
>
> Summary ASB Link States (Area 1)
>
> Link ID ADV Router Age Seq# Checksum
> 192.168.2.49 192.168.1.17 802 0x80000001 0xB251
>
> AS External Link States
>
> Link ID ADV Router Age Seq# Checksum Tag
> 192.168.2.48 192.168.1.49 1190 0x80000002 0xA7CF 0
> 192.168.2.48 192.168.2.49 829 0x80000001 0xA2D4 0
> RouterA#
>
>
> RouterB#show ip ospf database
>
> OSPF Router with ID (192.168.1.17) (Process ID 100)
>
>
> Router Link States (Area 0)
>
> Link ID ADV Router Age Seq# Checksum Link count
> 192.168.1.17 192.168.1.17 862 0x80000015 0x41F3 2
> 192.168.1.49 192.168.1.49 2020 0x80000004 0x49BA 2
> 192.168.2.49 192.168.2.49 864 0x80000002 0x38CC 2
>
> Summary Net Link States (Area 0)
>
> Link ID ADV Router Age Seq# Checksum
> 10.1.1.0 192.168.1.17 869 0x80000005 0xD2BE
>
> Router Link States (Area 1)
>
> Link ID ADV Router Age Seq# Checksum Link count
> 10.1.1.100 10.1.1.100 928 0x80000004 0x4E4 2
> 192.168.1.17 192.168.1.17 870 0x8000000F 0xEE46 2
>
> Summary Net Link States (Area 1)
>
> Link ID ADV Router Age Seq# Checksum
> 192.168.1.16 192.168.1.17 860 0x80000001 0xBC79
>
> Summary ASB Link States (Area 1)
>
> Link ID ADV Router Age Seq# Checksum
> 192.168.2.49 192.168.1.17 851 0x80000001 0xB251
>
> AS External Link States
>
> Link ID ADV Router Age Seq# Checksum Tag
> 192.168.2.48 192.168.1.49 1239 0x80000002 0xA7CF 0
> 192.168.2.48 192.168.2.49 876 0x80000001 0xA2D4 0
> RouterB#
>
>
> RouterA#trace 192.168.2.50
>
> Type escape sequence to abort.
> Tracing the route to RouterD (192.168.2.50)
>
> 1 10.1.1.1 16 msec 16 msec 16 msec
> 2 RouterC (192.168.1.18) 32 msec 28 msec 32 msec
> 3 RouterD (192.168.2.50) 44 msec * 40 msec
> RouterA#
>
>
> RouterB#trace 192.168.2.50
>
> Type escape sequence to abort.
> Tracing the route to RouterD (192.168.2.50)
>
> 1 RouterC (192.168.1.18) 16 msec 12 msec 16 msec
> 2 * * *
> 3 * * *
> 4
> RouterB#
>
>
>
>
> ""Stefan Dozier"" wrote in message
> [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > Well since I need the redistribution practice, figured
> > I'd plug your config into my pod and see if I could figure
> > out what gives!
> >
> > First thing I noticed...and it may just be a typo or dyslexia
> > (it's an affliction I experience often (smile))if you didn't
> > cut and paste your configs.
> > From your post...
> >
> > A is connected to B with 10.1.1.100 / 24 - Serial 0
> >
> > B is connected to A with 10.1.1.1 / 24 - Serial 0
> > B is connected to C with 192.168.1.17 /28 - Serial 1
> >
> > doesn't coincide with your posted configs
> >
> > hostname RouterA
> > !
> > interface Serial1
> > ip address 10.1.1.100 255.255.255.0
> > clockrate 64000
> >
> > hostname RouterB
> > !
> > interface Serial0
> > ip address 192.168.1.17 255.255.255.240
> > no fair-queue
> > !
> > interface Serial1
> > ip address 10.1.1.1 255.255.255.0
> >
> > Second...Here's my plugged in config and all devices have
> > connectivity to all other devices as expected.
> >
> > Caveat: only the necessary portions of the config are listed
> > for brevity and I changed some DTE/DCE interfaces and increased
> > the clockrate (personal preferrence)!
> >
> > hostname RouterA
> > !
> > interface Serial0
> > ip address 10.1.1.100 255.255.255.0
> > no fair-queue
> > !
> > router ospf 100
> > network 10.1.1.100 0.0.0.0 area 1
> > !
> > end
> > !
> > hostname RouterB
> > !
> > interface Serial0
> > ip address 10.1.1.1 255.255.255.0
> > no fair-queue
> > clockrate 4000000
> > !
> > interface Serial1
> > ip address 192.168.1.17 255.255.255.240
> > !
> > router ospf 100
> > network 192.168.1.17 0.0.0.0 area 0
> > network 10.1.1.1 0.0.0.0 area 1
> > !
> > end
> > !
> > hostname RouterC
> > !
> > interface Serial0
> > ip address 192.168.1.18 255.255.255.240
> > no fair-queue
> > clockrate 4000000
> > !
> > interface Serial1
> > ip address 192.168.2.49 255.255.255.240
> > clockrate 4000000
> > !
> > router ospf 100
> > redistribute igrp 200 metric-type 1 subnets
> > network 192.168.1.18 0.0.0.0 area 0
> > default-metric 10
> > !
> > router igrp 200
> > redistribute ospf 100
> > network 192.168.2.0
> > default-metric 10000 100 255 1 1500
> > !
> > ip route 192.168.1.0 255.255.255.0 Null0
> > !
> > end
> > !
> > hostname RouterD
> > !
> > interface Serial0
> > ip address 192.168.2.50 255.255.255.240
> > no fair-queue
> > !
> > router igrp 200
> > network 192.168.2.0
> > !
> > end
> >
> > HTH
> >
> > Stefan
> >
> > -----Original Message-----
> > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> > Hunt Lee
> > Sent: Friday, December 07, 2001 2:35 AM
> > To: [EMAIL PROTECTED]
> > Subject: Redistribution Question [7:28374]
> >
> >
> > I need some help on a Redistribution question:
> >
> > I have setup 4 routers:
> >
> > Router A - Router B - Router C - Router D
> >
> > A, B & C are running OSPF, and C & D are running IGRP - I'm trying to
> > redistribute between OSPF & IGRP routes:
> >
> > A is connected to B with 10.1.1.100 / 24 - Serial 0
> >
> > B is connected to A with 10.1.1.1 / 24 - Serial 0
> > B is connected to C with 192.168.1.17 /28 - Serial 1
> >
> > C is connected to B with 192.168.1.18 / 28 - Serial 0
> > C is connected to D with 192.168.2.49 / 28 - Serial 1
> >
> > D is connected to C with 192.168.2.50 / 28 - Serial 0
> >
> > However, I could only ping from D to A (& vice versa), but I couldn't
ping
> > from B to D, or D to B
> > N.B: D to C (and vice versa) is fine as they are directly connected
> >
> > Any help will be greatly appreciated.
> >
> > Thanks in advance,
> >
> > Hunt Lee
> >
> >
> > Below are the configs for the routers:
> >
> > Router A
> > version 11.0
> >
> > service udp-small-servers
> >
> > service tcp-small-servers
> >
> > !
> >
> > hostname RouterA
> >
> > !
> >
> > !
> >
> > no ip domain-lookup
> >
> > !
> >
> > interface Ethernet0
> >
> > no ip address
> >
> > shutdown
> >
> > !
> >
> > interface Serial0
> >
> > no ip address
> >
> > no fair-queue
> >
> > clockrate 64000
> >
> > !
> >
> > interface Serial1
> >
> > ip address 10.1.1.100 255.255.255.0
> >
> > clockrate 64000
> >
> > !
> >
> > router ospf 100
> >
> > network 10.1.1.100 0.0.0.0 area 1
> >
> > !
> >
> > ip host RouterB 10.1.1.1
> >
> > ip host RouterC 192.168.1.18
> >
> > ip host RouterD 192.168.2.50
> >
> > !
> >
> > line con 0
> >
> > line aux 0
> >
> > transport input all
> >
> > line vty 0 4
> >
> > login
> >
> > !
> >
> > end
> >
> >
> > Router B
> > version 11.0
> >
> > service udp-small-servers
> >
> > service tcp-small-servers
> >
> > !
> >
> > hostname RouterB
> >
> > !
> >
> > no ip domain-lookup
> >
> > !
> >
> > interface Ethernet0
> >
> > no ip address
> >
> > shutdown
> >
> > !
> >
> > interface Serial0
> >
> > ip address 192.168.1.17 255.255.255.240
> >
> > no fair-queue
> >
> > !
> >
> > interface Serial1
> >
> > ip address 10.1.1.1 255.255.255.0
> >
> > !
> >
> > router ospf 100
> >
> > network 192.168.1.17 0.0.0.0 area 0
> >
> > network 10.1.1.1 0.0.0.0 area 1
> >
> > !
> >
> > ip host RouterA 10.1.1.100
> >
> > ip host RouterC 192.168.1.18
> >
> > ip host RouterD 192.168.2.50
> >
> > !
> >
> > line con 0
> >
> > line aux 0
> >
> > transport input all
> >
> > line vty 0 4
> >
> > login
> >
> > !
> >
> > end
> >
> >
> >
> > Router C
> >
> > version 12.0
> >
> > service timestamps debug uptime
> >
> > service timestamps log uptime
> >
> > no service password-encryption
> >
> > !
> >
> > hostname RouterC
> >
> > !
> >
> > !
> >
> > ip subnet-zero
> >
> > no ip domain-lookup
> >
> > ip host RouterA 10.1.1.100
> >
> > ip host RouterB 192.168.1.17
> >
> > ip host RouterD 192.168.2.50
> >
> >
> >
> > !
> >
> > interface Ethernet0
> >
> > no ip address
> >
> > no ip directed-broadcast
> >
> > shutdown
> >
> > !
> >
> > interface Serial0
> >
> > ip address 192.168.1.18 255.255.255.240
> >
> > no ip directed-broadcast
> >
> > no ip mroute-cache
> >
> > no fair-queue
> >
> > clockrate 64000
> >
> > !
> >
> > interface Serial1
> >
> > ip address 192.168.2.49 255.255.255.240
> >
> > no ip directed-broadcast
> >
> > clockrate 64000
> >
> > !
> >
> > interface BRI0
> >
> > no ip address
> >
> > no ip directed-broadcast
> >
> > shutdown
> >
> > !
> >
> > router ospf 100
> >
> > redistribute igrp 200 metric-type 1 subnets
> >
> > network 192.168.1.18 0.0.0.0 area 0
> >
> > default-metric 10
> >
> > !
> >
> > router igrp 200
> >
> > redistribute ospf 100
> >
> > network 192.168.2.0
> >
> > default-metric 10000 100 255 1 1500
> >
> > !
> >
> > ip classless
> >
> > ip route 192.168.1.0 255.255.255.0 Null0
> >
> > !
> >
> > line con 0
> >
> > transport input none
> >
> > line aux 0
> >
> > line vty 0 4
> >
> > login
> >
> > !
> >
> > end
> >
> >
> >
> > Router D
> >
> > version 12.1
> >
> > service timestamps debug uptime
> >
> > service timestamps log uptime
> >
> > no service password-encryption
> >
> > !
> >
> > hostname RouterD
> >
> > !!
> >
> > ip subnet-zero
> >
> > no ip finger
> >
> > no ip domain-lookup
> >
> > ip host RouterC 192.168.1.49
> >
> > ip host RouterB 192.168.1.17
> >
> > ip host RouterA 10.1.1.100
> >
> > !
> >
> > interface Ethernet0
> >
> > no ip address
> >
> > shutdown
> >
> > !
> >
> > interface Serial0
> >
> > ip address 192.168.2.50 255.255.255.240
> >
> > no fair-queue
> >
> > !
> >
> > interface Serial1
> >
> > no ip address
> >
> > shutdown
> >
> > !
> >
> > router igrp 200
> >
> > network 192.168.2.0
> >
> > !
> >
> > ip classless
> >
> > ip http server
> >
> > !
> >
> > line con 0
> >
> > exec-timeout 0 0
> >
> > transport input none
> >
> > line 1 16
> >
> > line aux 0
> >
> > line vty 0 4
> >
> > login
> >
> > !
> >
> > end
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=28500&t=28374
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
