Try the router bgp command "maximum-paths 2" CM ----- Original Message ----- From: "Alejandro Acosta" To: Sent: Thursday, December 13, 2001 2:40 PM Subject: Re: BGP and ip load-sharing [7:28960]
> Hello, > Thanks for answering me. > I am using BGP because we have 2 Internet access and my customer > has 2 providers too. Then, we have to use BGP > > This is the BGP configuration > > neighbor xxx.xxx.xxx.xxx description eBGP with Mycustomer > neighbor xxx.xxx.xxx.xxx ebgp-multihop 2 > neighbor xxx.xxx.xxx.xxx password 7 ----- > neighbor xxx.xxx.xxx.xxx update-source Loopback1 > neighbor xxx.xxx.xxx.xxx version 4 > neighbor xxx.xxx.xxx.xxx maximum-prefix 8 > > I don't know why the packets that I am sending to my customer are > not simetric in both links. However, the customer sends to me almost > the same amount of traffic in both interfaces > > Thanks > > Alejandro > > MADMAN wrote: > > > > First problem, BGP doesn't load share but with IOS you can source an > > interface like a loopback, see BGP and loadsharing. > > > > If you have two parallel paths to a single provider why are you doing > > BGP??? Since you choose BGP I'll assume this is an Internet connection, > > set up two default routes, ip cef global command and the configs you > > have sent and you will have symetrical outgoing loadsharing. > > > > Dave > > > > Alejandro Acosta wrote: > > > > > > Hi All, > > > This is my first message in the list. > > > I am running a BGP session with a customer. It has 2 serial links with > us > > > (Each link of 2 Mbps). The customer and me have selected per-packet > sharing > > > in order to balanced the link. > > > In this moment, the traffic that comes from the customer is very > simetric > > > in both links, however, the traffic that is sent to the customer from us > is > > > not simetric. As far as I know (if I am not wrong), if we are using load > > > balacing per-packet, the incoming and outgoing traffic should be very > very > > > similar, right?. Why only the incoming traffic is simetric in this > moment. > > > > > > This is the configuration for both interfaces in my router: > > > > > > interface Serial2/0 > > > description Link 1 > > > bandwidth 2048 > > > ip address xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx > > > no ip directed-broadcast > > > ip load-sharing per-packet > > > no ip mroute-cache > > > load-interval 30 > > > no cdp enable > > > hold-queue 1024 out > > > ! > > > > > > interface Serial2/4 > > > description Link number 2 > > > bandwidth 2048 > > > ip address xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx > > > no ip directed-broadcast > > > ip load-sharing per-packet > > > no ip mroute-cache > > > load-interval 30 > > > no fair-queue > > > no cdp enable > > > > > > Any ideas? > > > > > > Thanks > > > > > > Alejandro Acosta > > > > > > P.D. I am using IOS 12.0(7)T > > -- > > David Madland > > Sr. Network Engineer > > CCIE# 2016 > > Qwest Communications Int. Inc. > > [EMAIL PROTECTED] > > 612-664-3367 > > > > "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=29080&t=28960 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]