I'm not sure if or where this is documented, but apparently beginning with some variants of 12.1 vlan trunking has been available of the 261x with only the 10 mbs ethernet port.
One of my pals discovered this just as he was about to walk into his CCIE lab attempt. Chuck ""MADMAN"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > You could configure subinterfaces forever, primarily used for > differant IPX encapsulation types on same physical network. What is new > is the ability to configure dot1q encapsulation on a 10M subinterface. > > Dave > > "Walker, Jim" wrote: > > > > I never tried it, but I didn't think you could configure a sub-interface > on a > > 10M ethernet port. > > > > -----Original Message----- > > From: Kent Hundley [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, March 28, 2002 5:20 PM > > To: Walker, Jim; [EMAIL PROTECTED] > > Subject: RE: Router question.. [7:39788] > > > > It's not necessary to use secondary addressing. Configure a 802.1q trunk > > port on the 2900 switch and configure one of the ethernet ports on the 2611 > > as a trunk port. (yes, 802.1q trunking is supported on ethernet) > > > > Configure appropriate addressing on the sub-interfaces of the 2611 and you > > still have a single free ethernet port for other connections. > > > > -Kent > > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > Walker, Jim > > Sent: Thursday, March 28, 2002 10:25 AM > > To: [EMAIL PROTECTED] > > Subject: RE: Router question.. [7:39788] > > > > 1. Create 2 separate vlans on the switch > > 2. Configure both ethernet ports, 1 with a secondary ip address > > 3. Connect up both ethernet ports on the router to 2 corresponding vlan > > configured port on the switch > > > > -----Original Message----- > > From: Ricky Chan [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, March 28, 2002 1:00 PM > > To: [EMAIL PROTECTED] > > Subject: RE: Router question.. [7:39788] > > > > It have only 2 regular ethernet port... > > > > -----Original Message----- > > From: Walker, Jim [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, March 28, 2002 12:55 PM > > To: Ricky Chan; [EMAIL PROTECTED] > > Subject: RE: Router question.. [7:39788] > > > > Yes, if 2600 series router has a fastethernet port. > > > > Router on a stick. > > > > -----Original Message----- > > From: Ricky Chan [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, March 28, 2002 12:43 PM > > To: [EMAIL PROTECTED] > > Subject: Router question.. [7:39788] > > > > Hi all, > > > > My boss just come up and give me a senario question like this. He told me > > that I owned a company which uses 3 different LANs, for example, > > 172.27.10.x, 172.27.11.x, 172.27.12.x. But I only have one cisco 2600 > series > > router and 2900 series switch. I can't use the serial ports from the > router. > > Just the two ethernet ports (by default). My question is, is it possible? > > Please advice. > > > > Thanks > > > > Ricky > -- > David Madland > Sr. Network Engineer > CCIE# 2016 > Qwest Communications Int. Inc. > [EMAIL PROTECTED] > 612-664-3367 > > "Emotion should reflect reason not guide it" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=39847&t=39788 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
