My XYPLEX MAXserver 1600 Terminal Server config notes. This is alot of peices I have pulled together to get my Maxserver 1600 (16port) working for my CCIE LAB rack. Since the Terminal server is not part of the lab I need to spend my money on thing like ISDN hardware. I was not able to find any instruction that let me put this config behind me quickly. Since we need to focus our time working on CCIE lab task (not the mysteries of Xplex Terminal server configs). I have put thess instruction/notes together.
resources: http://www.gno.org/~gdr/xyplex/ http://www.pimpworks.org/xyplex/ My system information getting started: 1)reset --->all light on 2)reset - hold--> until rotating lights stop and 15,16 go solid 3)hit return on console (after 20 seconds) type "access"(blind input) at greeting hit return. Terminal Server Configuration/Maintenance Menu 1. Display unit configuration 2. Modify unit configuration 3. Initialize server and port parameters 4. Revert to stored configuration S. Exit saving configuration changes X. Exit without saving configuration changes Enter menu selection [X]: 1 Stored Configuration New Configuration Parameter load method: NVS NVS Image load method: DTFTP BOOTP RARP DTFTP BOOTP RARP Dump method: BOOTP RARP BOOTP RARP XMOP/MOP filename: N/A N/A Default unit IP addr: 192.168.123.6 192.168.123.6 DTFTP host IP addr: 192.168.123.15 192.168.123.15 DTFTP gateway IP addr: 192.168.123.1 192.168.123.1 DTFTP filename: mx1500.sys mx1500.sys Load status messages: Enabled Enabled Network interface: Automatic Selection Automatic Selection Memory size expected: 4 Megabytes 4 Megabytes (Found 4 Megabytes) XYPLEX instructiuons ---basic boot config----------- Setting An MX-1600, MX-1608 or MX-1450 To Factory Defaults Straighten a paper clip and press into the pin-size hole next to console LED on the front panel of the unit. All LEDs on the front of the unit will light up. Press the paper clip in again and hold it in for 3-5 seconds. The LEDs will light up in a sweeping fashion from right to left, then left to right. When this sweeping stops, there will be 2 or 3 LEDS to the right lit, at this point release the paper clip. The LEDs will light up in a countdown pattern to 1 (diagnostic test pattern). Then they will all go out and the RUN light will be flashing very fast. You should have a terminal attached to one of the serial ports on the back of the unit. Press the ENTER key several times for the port to autobaud. You will see a text display similar to this: Terminal Server, Type 97, Rev G.00.00 Ethernet address 08-00-87-05-A1-16, port 2 Configuration in progress. Please wait Type the password "access" (there is no password prompt and it will not display the characters you type) and then press ENTER on your keyboard. The menu below will display. Please select the menu options and answer the questions as detailed below to default your unit. To Default The Server Load/Dump Parameters: Welcome to the Configuration Menu. Terminal Server Configuration/Maintenance Menu 1. Display unit configuration 2. Modify unit configuration 3. Initialize server and port parameters 4. Revert to stored configuration S. Exit saving configuration changes X. Exit without saving configuration changes Enter menu selection [X]: 2 -----[see my setup above for tftp no flash example]------ Initialize configuration to defaults (Y,N) [N]? Y Press ENTER on your keyboard at this time... To Default The Server & Port Parameters: Terminal Server Configuration/Maintenance Menu 1. Display unit configuration 2. Modify unit configuration 3. Initialize server and port parameters 4. Revert to stored configuration S. Exit saving configuration changes X. Exit without saving configuration changes Enter menu selection [X]: 3 When the software has been loaded, should default server and port parameters be used (Y,N) [N]? Y Save Configuration Changes And Reboot The Server: Terminal Server Configuration/Maintenance Menu 1. Display unit configuration 2. Modify unit configuration 3. Initialize server and port parameters 4. Revert to stored configuration S. Exit saving configuration changes X. Exit without saving configuration changes Enter menu selection [X]: S Save changes and exit (Y,N) [Y]? Y The access server will now reboot using factory settings. -----------------main command line menu------------------ #11111 (enter) ones in this caes(password)is blindly typed Xyplex> set privalege Password> [privalege password] "11111" Xyplex>> ---[DEFINE/SET server login prompt "string"]-----set unit password NOTE! SET (only applied to running config) DEFINE (stores value to database (next reload) but no running config) -------The Terminal Server config------ define port all telnet transmit immediate define port 1 telnet echo mode disable define port 2-16 telnet echo mode character define port all telnet newline nothing define port all telnet binary session mode passall define port all default session mode passall define port all broadcast disable define port 1 access local define port 2-16 access remote define port all speed 9600 define port all autobaud disable define port all modem enable define port all dsrlogout disable define port dsrwait disable define port 2-16 dtrwait forconnection define port all flow control disable define port 2-16 dcd timeout 0 define port all flow xon define port all typeahead 16348 define port all autoprompt disabled define port all line editor disabled define port all verification disabled logout port 2-16 -------------terminal server session control---------------------- telnet connection 192.168.123.6:2200 (server IP address:(2000+(100xport#)) OR connect trm:2200 from local session (trm is defined as domain name) # [enter] note:(I have to enter 11111 XYPLEX password to activate session? needs corrected but no time.) 2621_LAB_RTR_2> enter break (ctrl+break (hyper term),alt+B(tera term)) show session kill session (number) resume session 2 I hope this helps. Bryon Phillips Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=50635&t=14504 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]