Hi Ronnie, thanx for the reply.see router 2 configuration is almost same.I am sorry i have just removed that test bed I have to setup again.The confguration you can ge if u just to go the link mentioned at the end of this mail ,Just same configuration I used except multilink. If u still did not get the problem I can again Explain you. Regards, munit
Ronnie Higginbotham wrote: > Can you please post Router 2 config.... > > Ronnie > ""Munit Singla"" wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Hi, > > I am new to this group.A big Great hello to every one. > > Now my problem... > > > > I have leased line back to back routers.I have configured dialer > > interface although dialer interface is mostly used on switched ckts.But > > I am using here on leased line bavck to back.Now what happens after > > restting the interface physical > > It get disconnect after idle-timeout so I have made dilaer list to > > define interesting traffic also but still I am not able to trigger the > > call so dilaer interface timesout after being idle.I have used Map > > command > > Map protocol ip name broadcast ..I have not defined > > any string.I cannot define any string in above command as I have leased > > line ,no number to dial. > > During which the call is active i am able to transfer data but if it > > times out after idle time specified I am unable to activate the call. > > My config > > Configuration of router 1: > > router1#sh run > > Building configuration... > > > > Current configuration : 1209 bytes > > ! > > version 12.2 > > no parser cache > > service timestamps debug uptime > > service timestamps log uptime > > no service password-encryption > > ! > > hostname router1 > > ! > > no logging console > > enable secret 5 $1$xYa1$1.YkO1.NXT1epX8oSH8KQ1 > > ! > > username router2 password 0 abc > > ip subnet-zero > > ! > > frame-relay de-list 3 protocol ip gt 500 > > ! > > ! > > ! > > ! > > interface Loopback0 > > ip address 192.168.10.2 255.255.255.0 > > ! > > interface FastEthernet0 > > ip address 10.77.152.223 255.255.255.0 > > speed auto > > ! > > interface Serial0 > > no ip address > > encapsulation ppp > > dialer in-band > > dialer rotary-group 1 > > pulse-time 1 > > ! > > interface Serial1 > > no ip address > > encapsulation ppp > > shutdown > > dialer in-band > > dialer rotary-group 1 > > pulse-time 1 > > ! > > interface Dialer1 > > ip unnumbered Loopback0 > > encapsulation ppp > > dialer in-band > > dialer idle-timeout 30 > > dialer map ip 192.168.20.1 name router2 broadcast > > dialer-group 1 > > ppp authentication chap > > ppp direction callout > > ! > > ip classless > > ip route 0.0.0.0 0.0.0.0 10.77.152.129 > > ip route 192.168.20.1 255.255.255.255 Dialer1 > > no ip http server > > ! > > access-list 100 permit ip any any > > dialer-list 1 protocol ip list 100 > > ! > > line con 0 > > line aux 0 > > line vty 0 4 > > exec-timeout 200 0 > > password lab > > login > > line vty 5 15 > > login > > ! > > no scheduler allocate > > end > > > > router1# > > > > similar is configuration on router 2 > > > > Debug ppp nego o/p on router 1 > > > > > > 4:39:54: %LINK-3-UPDOWN: Interface Serial0, changed state to up > > 4:39:54: Se0 PPP: Using configured call direction > > 4:39:54: Se0 PPP: Treating connection as a callout > > 4:39:54: Se0 PPP: Phase is ESTABLISHING, Active Open [0 sess, 1 load] > > 4:39:54: Se0 LCP: O CONFREQ [Closed] id 203 len 15 > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) > > 4:39:54: Se0 LCP: MagicNumber 0x03B9ED37 (0x050603B9ED37) > > 4:39:54: Se0 LCP: I CONFREQ [REQsent] id 44 len 15 > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) > > 4:39:54: Se0 LCP: MagicNumber 0x00FF543D (0x050600FF543D) > > 4:39:54: Se0 LCP: O CONFACK [REQsent] id 44 len 15 > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) > > 4:39:54: Se0 LCP: MagicNumber 0x00FF543D (0x050600FF543D) > > 4:39:54: Se0 LCP: I CONFACK [ACKsent] id 203 len 15 > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) > > 4:39:54: Se0 LCP: MagicNumber 0x03B9ED37 (0x050603B9ED37) > > 4:39:54: Se0 LCP: State is Open > > 4:39:54: Se0 PPP: Phase is AUTHENTICATING, by both [0 sess, 1 load] > > 4:39:54: Se0 CHAP: O CHALLENGE id 240 len 28 from "router1" > > 4:39:54: Se0 CHAP: I CHALLENGE id 35 len 28 from "router2" > > 4:39:54: Se0 CHAP: O RESPONSE id 35 len 28 from "router1" > > 4:39:54: Se0 CHAP: I SUCCESS id 35 len 4 > > 4:39:54: Se0 CHAP: I RESPONSE id 240 len 28 from "router2" > > 4:39:54: Se0 CHAP: O SUCCESS id 240 len 4 > > 4:39:54: Se0 PPP: Phase is UP [0 sess, 1 load] > > 4:39:54: Se0 IPCP: O CONFREQ [Closed] id 8 len 10 > > 4:39:54: Se0 IPCP: Address 192.168.10.2 (0x0306C0A80A02) > > 4:39:54: Se0 CDPCP: O CONFREQ [Closed] id 8 len 4 > > 4:39:54: Se0 IPCP: I CONFREQ [REQsent] id 1 len 10 > > 4:39:54: Se0 IPCP: Address 192.168.20.1 (0x0306C0A81401) > > 4:39:54: Se0 IPCP: O CONFACK [REQsent] id 1 len 10 > > 4:39:54: Se0 IPCP: Address 192.168.20.1 (0x0306C0A81401) > > 4:39:54: Se0 IPCP: I CONFACK [ACKsent] id 8 len 10 > > 4:39:54: Se0 IPCP: Address 192.168.10.2 (0x0306C0A80A02) > > 4:39:54: Se0 IPCP: State is Open > > 4:39:54: Se0 LCP: I PROTREJ [Open] id 45 len 10 protocol CDPCP > > (0x820701080004) > > 4:39:54: Se0 CDPCP: State is Closed > > 4:39:54: Di1 IPCP: Install route to 192.168.20.1 > > 4:39:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, > > changed state > > to up > > > > > > > > router1#show dialer > > > > Di1 - dialer type = IN-BAND SYNC NO-PARITY > > Idle timer (30 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Number of active calls = 1 > > > > Dial String Successes Failures Last DNIS > > > > Se0 - dialer type = IN-BAND SYNC NO-PARITY > > Rotary group 1, priority 0 > > Idle timer (30 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Dialer state is data link layer up > > Time until disconnect 24 secs( this is decreasing after it expires I > > cant ping also) > > Connected to (router2) > > > > Se1 - dialer type = IN-BAND SYNC NO-PARITY > > Rotary group 1, priority 0 > > Idle timer (30 secs), Fast idle timer (20 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Dialer state is shutdown > > > > If I ping during this remaining time then the timer is reset idle timer > > but once it times off I am unable to generate the interesting traffic. > > I have enabled now debug ip packet detail when the idle disconnect time > > reaches zero it gives me this o/p.Problem is I am unable to generate > > interesting traffic after that will initiate call.Please help > > > > router1#ping 192.168.20.1 > > > > Type escape sequence to abort. > > Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: > > > > 00:07:21: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, > > rcvd 2 > > 00:07:21: UDP src=2606, dst=69 > > 00:07:21: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > sendi > > 00:07:21: ICMP type=8, code=0 > > 00:07:21: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > encap > > lation failed > > 00:07:21: ICMP type=8, code=0 > > 00:07:22: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, > > rcvd 2 > > 00:07:22: UDP src=9906, dst=69. > > 00:07:23: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > sendi > > 00:07:23: ICMP type=8, code=0 > > 00:07:23: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > encap > > lation failed > > 00:07:23: ICMP type=8, code=0. > > 00:07:25: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > sendi > > 00:07:25: ICMP type=8, code=0 > > 00:07:25: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > encap > > lation failed > > 00:07:25: ICMP type=8, code=0 > > 00:07:26: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, > > rcvd 2 > > 00:07:26: UDP src=2606, dst=69. > > 00:07:27: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, > > rcvd 2 > > 00:07:27: UDP src=9906, dst=69 > > 00:07:27: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > sendi > > 00:07:27: ICMP type=8, code=0 > > 00:07:27: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > encap > > lation failed > > 00:07:27: ICMP type=8, code=0. > > 00:07:29: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > sendi > > 00:07:29: ICMP type=8, code=0 > > 00:07:29: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, > > encap > > lation failed > > 00:07:29: ICMP type=8, code=0. > > Success rate is 0 percent (0/5) > > router1# > > > > > > router1(config)int dialer1,ip address 1.1.1.1 > > router2(config) int dialer 2,ip address 2.2.2.2 > > Above mentioned way also i tried.when i reset the interface it works but > > suppose during idle disconect time i dont send any traffic then I am > > unable to initiate a call as weused to do in case of isdn.same error > > messages here also comes if idle disconnect timer is expired.Moreover if > > any traffic is sent during the idle disconnect timer then it resets the > > timer.Everything is fine only question is that after dialer interface > > goes to idle state can i initiate call,I am unable to do here in case of > > leased lines.Moreover the configuration which i have showed you is from > > the following link which shows how to do load balacing on leased lines > > using ppp. > > http://www.cisco.com/warp/public/793/access_dial/pppmultilink.html > > Are we able to do it . > > waiting for u reply > > Munit Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=59202&t=59184 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]