Hi ronnie.
i have checked changing Dialer list also.Actually the problem is there
is one idle disconnect timer which u say I have
set here 30 sec.Now if I transfer packets within 30 sec when interface
was up.then this timer gets reset and working
fine.Now if dont transfer anything the timer will timeout and dialer
comes in IDLE state.so now if i have made access
list for matching interesting traffic .In debug it show matched
interesting traffic but its unable to initiate a call to serial
line ,dialer doesnot come out of idle state .is it Possible that on
serial lines to use such commands.or these commands
are only made for BRI interfaces.
I tried every combination.although this configurationis meant for Bri
interfaces but i want to use here and after that
want to gor load balacing using multilink on serial lines,but I am not
able to make a single connection whats the use of
thinking about loadbalacing.
any help will be appriciated as I am totally upset abt thsi problem
Regards,
Munit
Ronnie Higginbotham wrote:
Try changing the dialer list
----- Original Message -----
From: Munit Singla
To: Ronnie Higginbotham
Cc: [EMAIL PROTECTED]
Sent: Friday, December 13, 2002 6:09 PM
Subject: Re: Hi problem regarding PPP HELPpppppppp [7:59184]
Hi Ronnie,
thanx for the reply.see router 2 configuration is almost same.I
am sorry i have just removed that test
bed I have to setup again.The confguration you can ge if u just
to go the link mentioned at the end
of this mail ,Just same configuration I used except multilink.
If u still did not get the problem I can again Explain you.
Regards,
munit
Ronnie Higginbotham wrote:
> Try changing the dialer list
>
> ----- Original Message -----
> From: Munit Singla
> To: Ronnie Higginbotham
> Cc: [EMAIL PROTECTED]
> Sent: Friday, December 13, 2002 6:09 PM
> Subject: Re: Hi problem regarding PPP HELPpppppppp [7:59184]
> Hi Ronnie,
> thanx for the reply.see router 2 configuration is almost
> same.I am sorry i have just removed that test bed I have to
> setup again.The confguration you can ge if u just to go the
> link mentioned at the end of this mail ,Just same
> configuration I used except multilink.
> If u still did not get the problem I can again Explain you.
> Regards,
> munit
>
>
> Ronnie Higginbotham wrote:
>
> > Can you please post Router 2 config....
> >
> > Ronnie
> > ""Munit Singla"" wrote in message
> > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > > Hi,
> > > I am new to this group.A big Great hello to every one.
> > > Now my problem...
> > >
> > > I have leased line back to back routers.I have
> > configured dialer
> > > interface although dialer interface is mostly used on
> > switched ckts.But
> > > I am using here on leased line bavck to back.Now what
> > happens after
> > > restting the interface physical
> > > It get disconnect after idle-timeout so I have made
> > dilaer list to
> > > define interesting traffic also but still I am not able
> > to trigger the
> > > call so dilaer interface timesout after being idle.I
> > have used Map
> > > command
> > > Map protocol ip name broadcast ..I have not defined
> > > any string.I cannot define any string in above command
> > as I have leased
> > > line ,no number to dial.
> > > During which the call is active i am able to transfer
> > data but if it
> > > times out after idle time specified I am unable to
> > activate the call.
> > > My config
> > > Configuration of router 1:
> > > router1#sh run
> > > Building configuration...
> > >
> > > Current configuration : 1209 bytes
> > > !
> > > version 12.2
> > > no parser cache
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname router1
> > > !
> > > no logging console
> > > enable secret 5 $1$xYa1$1.YkO1.NXT1epX8oSH8KQ1
> > > !
> > > username router2 password 0 abc
> > > ip subnet-zero
> > > !
> > > frame-relay de-list 3 protocol ip gt 500
> > > !
> > > !
> > > !
> > > !
> > > interface Loopback0
> > > ip address 192.168.10.2 255.255.255.0
> > > !
> > > interface FastEthernet0
> > > ip address 10.77.152.223 255.255.255.0
> > > speed auto
> > > !
> > > interface Serial0
> > > no ip address
> > > encapsulation ppp
> > > dialer in-band
> > > dialer rotary-group 1
> > > pulse-time 1
> > > !
> > > interface Serial1
> > > no ip address
> > > encapsulation ppp
> > > shutdown
> > > dialer in-band
> > > dialer rotary-group 1
> > > pulse-time 1
> > > !
> > > interface Dialer1
> > > ip unnumbered Loopback0
> > > encapsulation ppp
> > > dialer in-band
> > > dialer idle-timeout 30
> > > dialer map ip 192.168.20.1 name router2 broadcast
> > > dialer-group 1
> > > ppp authentication chap
> > > ppp direction callout
> > > !
> > > ip classless
> > > ip route 0.0.0.0 0.0.0.0 10.77.152.129
> > > ip route 192.168.20.1 255.255.255.255 Dialer1
> > > no ip http server
> > > !
> > > access-list 100 permit ip any any
> > > dialer-list 1 protocol ip list 100
> > > !
> > > line con 0
> > > line aux 0
> > > line vty 0 4
> > > exec-timeout 200 0
> > > password lab
> > > login
> > > line vty 5 15
> > > login
> > > !
> > > no scheduler allocate
> > > end
> > >
> > > router1#
> > >
> > > similar is configuration on router 2
> > >
> > > Debug ppp nego o/p on router 1
> > >
> > >
> > > 4:39:54: %LINK-3-UPDOWN: Interface Serial0, changed
> > state to up
> > > 4:39:54: Se0 PPP: Using configured call direction
> > > 4:39:54: Se0 PPP: Treating connection as a callout
> > > 4:39:54: Se0 PPP: Phase is ESTABLISHING, Active Open [0
> > sess, 1 load]
> > > 4:39:54: Se0 LCP: O CONFREQ [Closed] id 203 len 15
> > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305)
> > > 4:39:54: Se0 LCP: MagicNumber 0x03B9ED37
> > (0x050603B9ED37)
> > > 4:39:54: Se0 LCP: I CONFREQ [REQsent] id 44 len 15
> > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305)
> > > 4:39:54: Se0 LCP: MagicNumber 0x00FF543D
> > (0x050600FF543D)
> > > 4:39:54: Se0 LCP: O CONFACK [REQsent] id 44 len 15
> > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305)
> > > 4:39:54: Se0 LCP: MagicNumber 0x00FF543D
> > (0x050600FF543D)
> > > 4:39:54: Se0 LCP: I CONFACK [ACKsent] id 203 len 15
> > > 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305)
> > > 4:39:54: Se0 LCP: MagicNumber 0x03B9ED37
> > (0x050603B9ED37)
> > > 4:39:54: Se0 LCP: State is Open
> > > 4:39:54: Se0 PPP: Phase is AUTHENTICATING, by both [0
> > sess, 1 load]
> > > 4:39:54: Se0 CHAP: O CHALLENGE id 240 len 28 from
> > "router1"
> > > 4:39:54: Se0 CHAP: I CHALLENGE id 35 len 28 from
> > "router2"
> > > 4:39:54: Se0 CHAP: O RESPONSE id 35 len 28 from
> > "router1"
> > > 4:39:54: Se0 CHAP: I SUCCESS id 35 len 4
> > > 4:39:54: Se0 CHAP: I RESPONSE id 240 len 28 from
> > "router2"
> > > 4:39:54: Se0 CHAP: O SUCCESS id 240 len 4
> > > 4:39:54: Se0 PPP: Phase is UP [0 sess, 1 load]
> > > 4:39:54: Se0 IPCP: O CONFREQ [Closed] id 8 len 10
> > > 4:39:54: Se0 IPCP: Address 192.168.10.2 (0x0306C0A80A02)
> >
> > > 4:39:54: Se0 CDPCP: O CONFREQ [Closed] id 8 len 4
> > > 4:39:54: Se0 IPCP: I CONFREQ [REQsent] id 1 len 10
> > > 4:39:54: Se0 IPCP: Address 192.168.20.1 (0x0306C0A81401)
> >
> > > 4:39:54: Se0 IPCP: O CONFACK [REQsent] id 1 len 10
> > > 4:39:54: Se0 IPCP: Address 192.168.20.1 (0x0306C0A81401)
> >
> > > 4:39:54: Se0 IPCP: I CONFACK [ACKsent] id 8 len 10
> > > 4:39:54: Se0 IPCP: Address 192.168.10.2 (0x0306C0A80A02)
> >
> > > 4:39:54: Se0 IPCP: State is Open
> > > 4:39:54: Se0 LCP: I PROTREJ [Open] id 45 len 10 protocol
> > CDPCP
> > > (0x820701080004)
> > > 4:39:54: Se0 CDPCP: State is Closed
> > > 4:39:54: Di1 IPCP: Install route to 192.168.20.1
> > > 4:39:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > Serial0,
> > > changed state
> > > to up
> > >
> > >
> > >
> > > router1#show dialer
> > >
> > > Di1 - dialer type = IN-BAND SYNC NO-PARITY
> > > Idle timer (30 secs), Fast idle timer (20 secs)
> > > Wait for carrier (30 secs), Re-enable (15 secs)
> > > Number of active calls = 1
> > >
> > > Dial String Successes Failures Last DNIS
> > >
> > > Se0 - dialer type = IN-BAND SYNC NO-PARITY
> > > Rotary group 1, priority 0
> > > Idle timer (30 secs), Fast idle timer (20 secs)
> > > Wait for carrier (30 secs), Re-enable (15 secs)
> > > Dialer state is data link layer up
> > > Time until disconnect 24 secs( this is decreasing after
> > it expires I
> > > cant ping also)
> > > Connected to (router2)
> > >
> > > Se1 - dialer type = IN-BAND SYNC NO-PARITY
> > > Rotary group 1, priority 0
> > > Idle timer (30 secs), Fast idle timer (20 secs)
> > > Wait for carrier (30 secs), Re-enable (15 secs)
> > > Dialer state is shutdown
> > >
> > > If I ping during this remaining time then the timer is
> > reset idle timer
> > > but once it times off I am unable to generate the
> > interesting traffic.
> > > I have enabled now debug ip packet detail when the idle
> > disconnect time
> > > reaches zero it gives me this o/p.Problem is I am unable
> > to generate
> > > interesting traffic after that will initiate call.Please
> > help
> > >
> > > router1#ping 192.168.20.1
> > >
> > > Type escape sequence to abort.
> > > Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout
> > is 2 seconds:
> > >
> > > 00:07:21: IP: s=10.10.10.13 (FastEthernet0),
> > d=255.255.255.255, len 49,
> > > rcvd 2
> > > 00:07:21: UDP src=2606, dst=69
> > > 00:07:21: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > sendi
> > > 00:07:21: ICMP type=8, code=0
> > > 00:07:21: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > encap
> > > lation failed
> > > 00:07:21: ICMP type=8, code=0
> > > 00:07:22: IP: s=10.10.10.13 (FastEthernet0),
> > d=255.255.255.255, len 49,
> > > rcvd 2
> > > 00:07:22: UDP src=9906, dst=69.
> > > 00:07:23: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > sendi
> > > 00:07:23: ICMP type=8, code=0
> > > 00:07:23: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > encap
> > > lation failed
> > > 00:07:23: ICMP type=8, code=0.
> > > 00:07:25: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > sendi
> > > 00:07:25: ICMP type=8, code=0
> > > 00:07:25: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > encap
> > > lation failed
> > > 00:07:25: ICMP type=8, code=0
> > > 00:07:26: IP: s=10.10.10.13 (FastEthernet0),
> > d=255.255.255.255, len 49,
> > > rcvd 2
> > > 00:07:26: UDP src=2606, dst=69.
> > > 00:07:27: IP: s=10.10.10.13 (FastEthernet0),
> > d=255.255.255.255, len 49,
> > > rcvd 2
> > > 00:07:27: UDP src=9906, dst=69
> > > 00:07:27: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > sendi
> > > 00:07:27: ICMP type=8, code=0
> > > 00:07:27: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > encap
> > > lation failed
> > > 00:07:27: ICMP type=8, code=0.
> > > 00:07:29: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > sendi
> > > 00:07:29: ICMP type=8, code=0
> > > 00:07:29: IP: s=192.168.10.2 (local), d=192.168.20.1
> > (Dialer1), len 100,
> > > encap
> > > lation failed
> > > 00:07:29: ICMP type=8, code=0.
> > > Success rate is 0 percent (0/5)
> > > router1#
> > >
> > >
> > > router1(config)int dialer1,ip address 1.1.1.1
> > > router2(config) int dialer 2,ip address 2.2.2.2
> > > Above mentioned way also i tried.when i reset the
> > interface it works but
> > > suppose during idle disconect time i dont send any
> > traffic then I am
> > > unable to initiate a call as weused to do in case of
> > isdn.same error
> > > messages here also comes if idle disconnect timer is
> > expired.Moreover if
> > > any traffic is sent during the idle disconnect timer
> > then it resets the
> > > timer.Everything is fine only question is that after
> > dialer interface
> > > goes to idle state can i initiate call,I am unable to do
> > here in case of
> > > leased lines.Moreover the configuration which i have
> > showed you is from
> > > the following link which shows how to do load balacing
> > on leased lines
> > > using ppp.
> > >
> > http://www.cisco.com/warp/public/793/access_dial/pppmultilink.html
> >
> > > Are we able to do it .
> > > waiting for u reply
> > > Munit
> >
> > Message Posted at:
> > http://www.groupst
> > dy.com/form/read.php?f=7&i=59201&t=59184
> > --------------------------------------------------
> > FAQ, list archives, and subscription info:
> > http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to
> > [EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59204&t=59184
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
