Hi, I am new to this group.A big Great hello to every one. Now my problem...
I have leased line back to back routers.I have configured dialer interface although dialer interface is mostly used on switched ckts.But I am using here on leased line bavck to back.Now what happens after restting the interface physical It get disconnect after idle-timeout so I have made dilaer list to define interesting traffic also but still I am not able to trigger the call so dilaer interface timesout after being idle.I have used Map command Map protocol ip name broadcast ..I have not defined any string.I cannot define any string in above command as I have leased line ,no number to dial. During which the call is active i am able to transfer data but if it times out after idle time specified I am unable to activate the call. My config Configuration of router 1: router1#sh run Building configuration... Current configuration : 1209 bytes ! version 12.2 no parser cache service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname router1 ! no logging console enable secret 5 $1$xYa1$1.YkO1.NXT1epX8oSH8KQ1 ! username router2 password 0 abc ip subnet-zero ! frame-relay de-list 3 protocol ip gt 500 ! ! ! ! interface Loopback0 ip address 192.168.10.2 255.255.255.0 ! interface FastEthernet0 ip address 10.77.152.223 255.255.255.0 speed auto ! interface Serial0 no ip address encapsulation ppp dialer in-band dialer rotary-group 1 pulse-time 1 ! interface Serial1 no ip address encapsulation ppp shutdown dialer in-band dialer rotary-group 1 pulse-time 1 ! interface Dialer1 ip unnumbered Loopback0 encapsulation ppp dialer in-band dialer idle-timeout 30 dialer map ip 192.168.20.1 name router2 broadcast dialer-group 1 ppp authentication chap ppp direction callout ! ip classless ip route 0.0.0.0 0.0.0.0 10.77.152.129 ip route 192.168.20.1 255.255.255.255 Dialer1 no ip http server ! access-list 100 permit ip any any dialer-list 1 protocol ip list 100 ! line con 0 line aux 0 line vty 0 4 exec-timeout 200 0 password lab login line vty 5 15 login ! no scheduler allocate end router1# similar is configuration on router 2 Debug ppp nego o/p on router 1 4:39:54: %LINK-3-UPDOWN: Interface Serial0, changed state to up 4:39:54: Se0 PPP: Using configured call direction 4:39:54: Se0 PPP: Treating connection as a callout 4:39:54: Se0 PPP: Phase is ESTABLISHING, Active Open [0 sess, 1 load] 4:39:54: Se0 LCP: O CONFREQ [Closed] id 203 len 15 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) 4:39:54: Se0 LCP: MagicNumber 0x03B9ED37 (0x050603B9ED37) 4:39:54: Se0 LCP: I CONFREQ [REQsent] id 44 len 15 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) 4:39:54: Se0 LCP: MagicNumber 0x00FF543D (0x050600FF543D) 4:39:54: Se0 LCP: O CONFACK [REQsent] id 44 len 15 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) 4:39:54: Se0 LCP: MagicNumber 0x00FF543D (0x050600FF543D) 4:39:54: Se0 LCP: I CONFACK [ACKsent] id 203 len 15 4:39:54: Se0 LCP: AuthProto CHAP (0x0305C22305) 4:39:54: Se0 LCP: MagicNumber 0x03B9ED37 (0x050603B9ED37) 4:39:54: Se0 LCP: State is Open 4:39:54: Se0 PPP: Phase is AUTHENTICATING, by both [0 sess, 1 load] 4:39:54: Se0 CHAP: O CHALLENGE id 240 len 28 from "router1" 4:39:54: Se0 CHAP: I CHALLENGE id 35 len 28 from "router2" 4:39:54: Se0 CHAP: O RESPONSE id 35 len 28 from "router1" 4:39:54: Se0 CHAP: I SUCCESS id 35 len 4 4:39:54: Se0 CHAP: I RESPONSE id 240 len 28 from "router2" 4:39:54: Se0 CHAP: O SUCCESS id 240 len 4 4:39:54: Se0 PPP: Phase is UP [0 sess, 1 load] 4:39:54: Se0 IPCP: O CONFREQ [Closed] id 8 len 10 4:39:54: Se0 IPCP: Address 192.168.10.2 (0x0306C0A80A02) 4:39:54: Se0 CDPCP: O CONFREQ [Closed] id 8 len 4 4:39:54: Se0 IPCP: I CONFREQ [REQsent] id 1 len 10 4:39:54: Se0 IPCP: Address 192.168.20.1 (0x0306C0A81401) 4:39:54: Se0 IPCP: O CONFACK [REQsent] id 1 len 10 4:39:54: Se0 IPCP: Address 192.168.20.1 (0x0306C0A81401) 4:39:54: Se0 IPCP: I CONFACK [ACKsent] id 8 len 10 4:39:54: Se0 IPCP: Address 192.168.10.2 (0x0306C0A80A02) 4:39:54: Se0 IPCP: State is Open 4:39:54: Se0 LCP: I PROTREJ [Open] id 45 len 10 protocol CDPCP (0x820701080004) 4:39:54: Se0 CDPCP: State is Closed 4:39:54: Di1 IPCP: Install route to 192.168.20.1 4:39:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up router1#show dialer Di1 - dialer type = IN-BAND SYNC NO-PARITY Idle timer (30 secs), Fast idle timer (20 secs) Wait for carrier (30 secs), Re-enable (15 secs) Number of active calls = 1 Dial String Successes Failures Last DNIS Se0 - dialer type = IN-BAND SYNC NO-PARITY Rotary group 1, priority 0 Idle timer (30 secs), Fast idle timer (20 secs) Wait for carrier (30 secs), Re-enable (15 secs) Dialer state is data link layer up Time until disconnect 24 secs( this is decreasing after it expires I cant ping also) Connected to (router2) Se1 - dialer type = IN-BAND SYNC NO-PARITY Rotary group 1, priority 0 Idle timer (30 secs), Fast idle timer (20 secs) Wait for carrier (30 secs), Re-enable (15 secs) Dialer state is shutdown If I ping during this remaining time then the timer is reset idle timer but once it times off I am unable to generate the interesting traffic. I have enabled now debug ip packet detail when the idle disconnect time reaches zero it gives me this o/p.Problem is I am unable to generate interesting traffic after that will initiate call.Please help router1#ping 192.168.20.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: 00:07:21: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, rcvd 2 00:07:21: UDP src=2606, dst=69 00:07:21: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, sendi 00:07:21: ICMP type=8, code=0 00:07:21: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, encap lation failed 00:07:21: ICMP type=8, code=0 00:07:22: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, rcvd 2 00:07:22: UDP src=9906, dst=69. 00:07:23: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, sendi 00:07:23: ICMP type=8, code=0 00:07:23: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, encap lation failed 00:07:23: ICMP type=8, code=0. 00:07:25: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, sendi 00:07:25: ICMP type=8, code=0 00:07:25: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, encap lation failed 00:07:25: ICMP type=8, code=0 00:07:26: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, rcvd 2 00:07:26: UDP src=2606, dst=69. 00:07:27: IP: s=10.10.10.13 (FastEthernet0), d=255.255.255.255, len 49, rcvd 2 00:07:27: UDP src=9906, dst=69 00:07:27: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, sendi 00:07:27: ICMP type=8, code=0 00:07:27: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, encap lation failed 00:07:27: ICMP type=8, code=0. 00:07:29: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, sendi 00:07:29: ICMP type=8, code=0 00:07:29: IP: s=192.168.10.2 (local), d=192.168.20.1 (Dialer1), len 100, encap lation failed 00:07:29: ICMP type=8, code=0. Success rate is 0 percent (0/5) router1# router1(config)int dialer1,ip address 1.1.1.1 router2(config) int dialer 2,ip address 2.2.2.2 Above mentioned way also i tried.when i reset the interface it works but suppose during idle disconect time i dont send any traffic then I am unable to initiate a call as weused to do in case of isdn.same error messages here also comes if idle disconnect timer is expired.Moreover if any traffic is sent during the idle disconnect timer then it resets the timer.Everything is fine only question is that after dialer interface goes to idle state can i initiate call,I am unable to do here in case of leased lines.Moreover the configuration which i have showed you is from the following link which shows how to do load balacing on leased lines using ppp. http://www.cisco.com/warp/public/793/access_dial/pppmultilink.html Are we able to do it . waiting for u reply Munit Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=59184&t=59184 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]