Just before I got your reply, I finally found a document on CCO that explained that I had to have the 'ip pim rp-address ...' configured on both routers which I did. No I'm not seeing the earlier problem about not being able to join the Auto-RP router.
As I was seeing before, I can see the multicast entry in the mroute table on the RP sever, but it is Pruned by the looks of it and it is not sending out the serial port to the other router... What could it be now? 2620 Mroute 2620#sho ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, s - SSM Outgoing interface flags: H - Hardware switched Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.255.255.250), 00:18:05/00:03:13, RP 10.1.1.1, flags: S Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0, Forward/Sparse-Dense, 00:18:05/00:03:13 (*, 224.0.1.40), 19:06:50/00:00:00, RP 10.1.1.1, flags: SJCL Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Serial0/0, Forward/Sparse-Dense, 00:55:50/00:02:57 FastEthernet0/0, Forward/Sparse-Dense, 19:06:50/00:02:45 (*, 239.192.47.232), 00:00:04/00:02:59, RP 10.1.1.1, flags: SP Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: Null (10.1.1.2, 239.192.47.232), 00:00:06/00:02:59, flags: PT Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0 Outgoing interface list: Null 2514 Mroute 2514#sho ip mroute IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, s - SSM Outgoing interface flags: H - Hardware switched Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.255.255.250), 00:19:03/00:01:59, RP 10.1.1.1, flags: SJC Incoming interface: Serial0, RPF nbr 20.1.1.1 Outgoing interface list: Ethernet0, Forward/Sparse-Dense, 00:19:03/00:01:59 (*, 224.0.1.40), 00:34:45/00:00:00, RP 10.1.1.1, flags: SJCL Incoming interface: Serial0, RPF nbr 20.1.1.1 Outgoing interface list: Ethernet0, Forward/Sparse-Dense, 00:34:45/00:02:03 As you can see the 2620 is aware of the multicast stream from FE0/0, but it's Pruned and it's not putting it ouot to the 2514? Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61970&t=61950 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]