I hear you. Touché's mast blocks are very close to mast. No way you could pull the halyard outward.
I'd definitely have to go with the apsltd set up. Dennis C. Sent from my iPhone > On Apr 15, 2014, at 7:30 PM, Chuck S <cscheaf...@comcast.net> wrote: > > Hi Dennis, > On our 34R, the halyards exit the mast high up and run to mast blocks at the > collar well away from the mast, so a tug would probably pull the line into > the camcleat. I recently mounted a camcleat on the mast well below the exit > for my main halyard so I can control it there. Tensioning the line with the > winch pulls it out of the camcleat. > > The flipped camcleat might work on our boat if it was mounted higher up and > closer to the exit, so the man jumping the halyard would need to pull it away > from the mast more to engage the camcleat? Like working a window shade cord. > I'm considering adding another camcleat and not sure which is better? > > > Chuck > Resolute > 1990 C&C 34R > Atlantic City, NJ > > From: "Dennis C." <capt...@gmail.com> > To: "CnClist" <cnc-list@cnc-list.com> > Sent: Monday, April 14, 2014 1:07:05 PM > Subject: Re: Stus-List Spinnaker Stops > > Thanks, Andy > > That's slick. Here's the link: > <http://www.apsltd.com/c-6176-spinnaker-halyard-cam-base.aspx> > > I might order one of those. > > Dennis C. > Touche' 35-1 #83 > Mandeville, LA > > >> On Mon, Apr 14, 2014 at 10:06 AM, Andrew Burton <a.burton.sai...@gmail.com> >> wrote: >> Try the APS spinnaker halyard mast base. It essentially turns the cleat >> around and when you haul in the tail in the cockpit and cleat it there a tug >> pops the halyard out of the mast cleat. Works very well on the J/80. >> >> Andy >> C&C 40 >> Peregrine >> >> >> >> >> Andrew Burton >> 61 W Narragansett >> Newport, RI >> USA 02840 >> >> http://sites.google.com/site/andrewburtonyachtservices/ >> +401 965-5260 >> >> On Apr 14, 2014, at 8:58, "Hoyt, Mike" <mike.h...@impgroup.com> wrote: >> >> My mast is set up with the cam cleat for spin halyard as well. It then goes >> back to cockpit thru winch and clutch as you have described. Works well >> when mast/foredeck person is aware of it and uses it. Does tend to go into >> the cam cleat even when hoisted from cockpit and I have lost track of the >> number of times a takedown was delayed because of the mast cam cleat. If >> mast/foredeck person is consistent and on the ball should not be a problem >> however on smaller boats where this is foredeck person and no mast person >> the foredeck person is usually busy tripping the guy and unless they had >> checked the mast cam cleat before going fwd to trip the guy the delay will >> happen again >> >> >> >> All that said it certainly does speed up the launch >> >> >> >> Mike >> >> Nut Case >> >> >> >> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Dennis C. >> Sent: Friday, April 11, 2014 12:16 PM >> To: CnClist >> Subject: Re: Stus-List Spinnaker Stops >> >> >> >> Offset them an inch or two so they are not directly in the line between the >> exit and the turning block. That reduces the potential for the halyard to >> inadvertently slip into the cleat. >> >> Dennis C. >> >> >> >> >> >> On Fri, Apr 11, 2014 at 10:06 AM, Bill Coleman <colt...@verizon.net> wrote: >> >> The Port side goes aft to a clutch, and the SB is handled at the mast base. >> >> That is a really good idea, thanks, I think I will add a couple of those. >> >> >> >> >> >> Bill Coleman >> >> C&C 39 >> >> >> >> From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Dennis C. >> Sent: Friday, April 11, 2014 10:59 AM >> To: CnClist >> Subject: Re: Stus-List Spinnaker Stops >> >> >> >> Bill, >> >> Assuming your spin halyard is run aft, I've crewed on boats that have a cam >> cleat on the mast that can temporarily stop the halyard. The mast person is >> the only one doing the hoist. Eliminates the pit person having to tail the >> halyard. Once the chute is up, the halyard tail can be pulled through the >> rope clutch. Just have to remember to release it from the cam cleat before >> the drop. >> >> >> >> It can be set up so it pops out of the cleat when the halyard is ground >> tight by a cabin top winch. >> >> >> >> Dennis C. >> >> Touche' 35-1 #83 >> >> Mandeville, LA >> >> >> >> On Fri, Apr 11, 2014 at 9:35 AM, Bill Coleman <colt...@verizon.net> wrote: >> >> We are usually light handed on crew, and it is a big sail. If I had 8 great >> crew maybe I would be apt to launch bare in heavier air, but mostly we >> don't. >> Once on one of our Fall Cruise across the lake, one of the guys >> instinctively grabbed the Spinnaker halyard harder as it started to get >> away, and got some very bad burns, and it was only blowing 15. I like the >> control and relative safety of a banded sail. >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> http://www.cncphotoalbum.com >> CnC-List@cnc-list.com > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
