Brad My race crew hates self tailers. I prefer them for thejib sheets. Hard to imagine the bearings are shot. A good clean and regrease should do it. Use oil not grease on springs and pawls.
Joel 35/3 Annapolis On Saturday, February 21, 2015, Bradley Lumgair via CnC-List < cnc-list@cnc-list.com> wrote: > Was at Toronto Boat Show, just realized I did pick up a catalogue for > Garhauer, nice stuff as I recall. will check them out further. > The plan in my little head right now is to 1) change out the halyards for > all synthetic, 2) try to pull new wire from the top of the mast and rig new > instruments, the old don't work anyways so I'm not losing anything even if > I'm unsuccessful, 3) check bushings/trade out sheaves after the mast comes > down in the fall. > Theres a lot of talk about self tailing winches, aftermarket or original > equipment? Eight Barient winches on ours, none are self tailing and all > need servicing, I see West Marine sells springs and pawls, I should get a > couple of sets for the inevitable loss, if needed I should be able to pick > up bearings at a local bearing shop? > Thank you for all your advise and suggestions > Brad > > Sent, miraculously through cyberspace, > from my iPad! > > > On Feb 21, 2015, at 04:28, cnc-list-requ...@cnc-list.com <javascript:;> > wrote: > > > > Send CnC-List mailing list submissions to > > cnc-list@cnc-list.com <javascript:;> > > > > To subscribe or unsubscribe via the World Wide Web, visit > > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > or, via email, send a message with subject or body 'help' to > > cnc-list-requ...@cnc-list.com <javascript:;> > > > > You can reach the person managing the list at > > cnc-list-ow...@cnc-list.com <javascript:;> > > > > When replying, please edit your Subject line so it is more specific > > than "Re: Contents of CnC-List digest..." > > Today's Topics: > > > > 1. Re: C&C 33 MKII (Gary Nylander) > > 2. Re: C&C 33 MKII > Barient 24ST (Nauset Beach) > > 3. Re: C&C 33 MKII (Marek Dziedzic) > > 4. Refilling 10 lb propane tank (mike amirault) > > 5. Re: Refilling 10 lb propane tank (Josh Muckley) > > 6. salt water siphoning into sink (mike amirault) > > 7. Re: salt water siphoning into sink (Joel Aronson) > > 8. Re: salt water siphoning into sink (Mike Brannon) > > 9. Re: salt water siphoning into sink (Ken Heaton) > > 10. Re: salt water siphoning into sink (Jack Fitzgerald) > > 11. Re: salt water siphoning into sink (Bruno Lachance) > > 12. Re: salt water siphoning into sink (Graham Collins) > > 13. Re: Refilling 10 lb propane tank (Graham Collins) > > 14. Re: salt water siphoning into sink (Dennis C.) > > 15. Re: salt water siphoning into sink (Andrew Burton) > > 16. Re: salt water siphoning into sink (Russ & Melody) > > 17. Re: salt water siphoning into sink (dwight veinot) > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > <mime-attachment> > > _______________________________________________ > > CnC-List mailing list > > CnC-List@cnc-list.com <javascript:;> > > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com <javascript:;> > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > -- Joel 301 541 8551
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
