Thanks, everyone!

Tim and Dave, you mentioned issues getting the Martec to open at low revs.
Would a short boost to high revs when you start the engine solve that issue?

Sam

On Fri, Feb 5, 2016 at 12:48 PM, Dave via CnC-List <cnc-list@cnc-list.com>
wrote:

> I'm with Tim. I had my Martek rebuilt last spring and was really
> disappointed because even after the rebuild it wouldn't always open evenly.
> I'm replacing it with a FlexFold. By the way reverse was OK you just need
> to get use to it.
>
> Dave
> C&C 35 MK 3
> Saltaire
> Bristol, RI
>
> ------------------------------
> *From: *"Jake Brodersen via CnC-List" <cnc-list@cnc-list.com>
> *To: *cnc-list@cnc-list.com
> *Cc: *"Jake Brodersen" <captain_j...@cox.net>
> *Sent: *Wednesday, February 3, 2016 7:35:37 PM
> *Subject: *Re: Stus-List Propeller Question for 35-3
>
>
> Sam,
>
>
>
> IIRC, I’m swinging a 10x16 Martec elliptical prop.  Good forward
> performance.  Reverse requires a lot of rpms to get a response, but it
> works for me.
>
> I’m just a high speed – low drag racer anyway.
>
>
>
> Jake
>
>
>
> *Jake Brodersen*
>
> *C&C 35 Mk-III “Midnight Mistress”*
>
> *Hampton VA*
>
>
>
>
>
>
>
> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Sam
> Wheeler via CnC-List
> *Sent:* Wednesday, February 3, 2016 17:08
> *To:* cnc-list@cnc-list.com
> *Cc:* Sam Wheeler <samwheeler.s...@gmail.com>
> *Subject:* Stus-List Propeller Question for 35-3
>
>
>
> Hi everyone,
>
>
>
> I recently bought a 35-3, and one of the projects it came with was the
> prop had galvanic corrosion and needed to be replaced.  It's a fixed two
> blade.
>
>
>
> The previous owners adjusted the pitch on it, apparently from 10 to 8.
> They seemed to think that improved performance but the boatyard is telling
> me that the specs for the boat and engine call for 10.  Does anyone have
> any thoughts on this?
>
>
>
> Thanks,
>
> Sam
>
>
>
>
>
> ---------- Forwarded message ----------
> From: *Carston Grasvik* <cars...@svendsens.com>
> Date: Wed, Feb 3, 2016 at 8:19 AM
> Subject: FW: Propeller for C&C 35
> To: Sam Wheeler <samwheeler.s...@gmail.com>
>
> Hi Sam,
>
>
>
> It appears your old prop has an odd pitch to it. The prop I estimated for
> you has a 10 degree pitch which is specified for your boat and engine.
> Please see note below from our prop people and advise what you’d like to do.
>
>
>
> Best Regards,
>
>
>
> Carston
>
>
>
> *From:* Ernel Elkin [mailto:prop...@pacbell.net]
> *Sent:* Monday, February 01, 2016 3:47 PM
> *To:* Carston Grasvik
> *Subject:* Propeller for C&C 35
>
>
>
> HI CARSTON - DAVE MEASURED THE PITCH ON THE 2 BLADE AND IT IS 8"!
> UNFORTUNATELY, THE PROP I FOUND FOR YOU HAD ALREADY BEEN REPITCHED FROM 12
> TO 10 AND CAN NOT BE REPITCHED ANYMORE.  IT WOULD PROBABLY CRACK.
>
>
>
> I LOOKED AROUND AND FOUND ANOTHER 18"X 10", BUT THE PILOT BORE IS 1-1/8",
> SO THE CUSTOMER WOULD HAVE TO USE A BUSHING WITH IT AND HAVE IT REPITCHED
> TO 8".  BUSHING COST IS $74 AND REPITCHING IS $150.
>
>
>
> KIND OF A WEIRD SIZE.  THE LOWEST PITCH AVAILABLE IS 10".  PLEASE DISCUSS
> WITH YOUR CUSTOMER.  THANKS.
>
>
>
> ERNEL
>
>
>
> _______________________________________________
>
> Email address:
> CnC-List@cnc-list.com
> To change your list preferences, including unsubscribing -- go to the
> bottom of page at:
> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
>
>
>
> _______________________________________________
>
> Email address:
> CnC-List@cnc-list.com
> To change your list preferences, including unsubscribing -- go to the
> bottom of page at:
> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
>
>
>
_______________________________________________

Email address:
CnC-List@cnc-list.com
To change your list preferences, including unsubscribing -- go to the bottom of 
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com

Reply via email to