http://git-wip-us.apache.org/repos/asf/incubator-mynewt-core/blob/35529b95/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd.h ---------------------------------------------------------------------- diff --git a/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd.h b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd.h new file mode 100644 index 0000000..f57645a --- /dev/null +++ b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd.h @@ -0,0 +1,337 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_pcd.h + * @author MCD Application Team + * @version V1.2.0 + * @date 30-December-2016 + * @brief Header file of PCD HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_PCD_H +#define __STM32F7xx_HAL_PCD_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_ll_usb.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @addtogroup PCD + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup PCD_Exported_Types PCD Exported Types + * @{ + */ + +/** + * @brief PCD State structure definition + */ +typedef enum +{ + HAL_PCD_STATE_RESET = 0x00U, + HAL_PCD_STATE_READY = 0x01U, + HAL_PCD_STATE_ERROR = 0x02U, + HAL_PCD_STATE_BUSY = 0x03U, + HAL_PCD_STATE_TIMEOUT = 0x04U +} PCD_StateTypeDef; + +/* Device LPM suspend state */ +typedef enum +{ + LPM_L0 = 0x00U, /* on */ + LPM_L1 = 0x01U, /* LPM L1 sleep */ + LPM_L2 = 0x02U, /* suspend */ + LPM_L3 = 0x03U, /* off */ +}PCD_LPM_StateTypeDef; + +typedef USB_OTG_GlobalTypeDef PCD_TypeDef; +typedef USB_OTG_CfgTypeDef PCD_InitTypeDef; +typedef USB_OTG_EPTypeDef PCD_EPTypeDef ; + +/** + * @brief PCD Handle Structure definition + */ +typedef struct +{ + PCD_TypeDef *Instance; /*!< Register base address */ + PCD_InitTypeDef Init; /*!< PCD required parameters */ + PCD_EPTypeDef IN_ep[16]; /*!< IN endpoint parameters */ + PCD_EPTypeDef OUT_ep[16]; /*!< OUT endpoint parameters */ + HAL_LockTypeDef Lock; /*!< PCD peripheral status */ + __IO PCD_StateTypeDef State; /*!< PCD communication state */ + uint32_t Setup[12]; /*!< Setup packet buffer */ + PCD_LPM_StateTypeDef LPM_State; /*!< LPM State */ + uint32_t BESL; + uint32_t lpm_active; /*!< Enable or disable the Link Power Management . + This parameter can be set to ENABLE or DISABLE */ + + uint32_t battery_charging_active; /*!< Enable or disable Battery charging. + This parameter can be set to ENABLE or DISABLE */ + void *pData; /*!< Pointer to upper stack Handler */ +} PCD_HandleTypeDef; + +/** + * @} + */ + +/* Include PCD HAL Extension module */ +#include "stm32f7xx_hal_pcd_ex.h" + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup PCD_Exported_Constants PCD Exported Constants + * @{ + */ + +/** @defgroup PCD_Speed PCD Speed + * @{ + */ +#define PCD_SPEED_HIGH 0U +#define PCD_SPEED_HIGH_IN_FULL 1U +#define PCD_SPEED_FULL 2U +/** + * @} + */ + +/** @defgroup PCD_PHY_Module PCD PHY Module + * @{ + */ +#define PCD_PHY_ULPI 1U +#define PCD_PHY_EMBEDDED 2U +#define PCD_PHY_UTMI 3U +/** + * @} + */ + +/** @defgroup PCD_Turnaround_Timeout Turnaround Timeout Value + * @{ + */ +#ifndef USBD_HS_TRDT_VALUE + #define USBD_HS_TRDT_VALUE 9U +#endif /* USBD_HS_TRDT_VALUE */ +#ifndef USBD_FS_TRDT_VALUE + #define USBD_FS_TRDT_VALUE 5U +#endif /* USBD_HS_TRDT_VALUE */ + +/** + * @} + */ + +/** + * @} + */ + +/* Exported macros -----------------------------------------------------------*/ +/** @defgroup PCD_Exported_Macros PCD Exported Macros + * @brief macros to handle interrupts and specific clock configurations + * @{ + */ +#define __HAL_PCD_ENABLE(__HANDLE__) USB_EnableGlobalInt ((__HANDLE__)->Instance) +#define __HAL_PCD_DISABLE(__HANDLE__) USB_DisableGlobalInt ((__HANDLE__)->Instance) + +#define __HAL_PCD_GET_FLAG(__HANDLE__, __INTERRUPT__) ((USB_ReadInterrupts((__HANDLE__)->Instance) & (__INTERRUPT__)) == (__INTERRUPT__)) +#define __HAL_PCD_CLEAR_FLAG(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->GINTSTS) = (__INTERRUPT__)) +#define __HAL_PCD_IS_INVALID_INTERRUPT(__HANDLE__) (USB_ReadInterrupts((__HANDLE__)->Instance) == 0) + + +#define __HAL_PCD_UNGATE_PHYCLOCK(__HANDLE__) *(__IO uint32_t *)((uint32_t)((__HANDLE__)->Instance) + USB_OTG_PCGCCTL_BASE) &= \ + ~(USB_OTG_PCGCCTL_STOPCLK) + +#define __HAL_PCD_GATE_PHYCLOCK(__HANDLE__) *(__IO uint32_t *)((uint32_t)((__HANDLE__)->Instance) + USB_OTG_PCGCCTL_BASE) |= USB_OTG_PCGCCTL_STOPCLK + +#define __HAL_PCD_IS_PHY_SUSPENDED(__HANDLE__) ((*(__IO uint32_t *)((uint32_t)((__HANDLE__)->Instance) + USB_OTG_PCGCCTL_BASE))&0x10) + +#define USB_OTG_FS_WAKEUP_EXTI_RISING_EDGE ((uint32_t)0x08U) +#define USB_OTG_FS_WAKEUP_EXTI_FALLING_EDGE ((uint32_t)0x0CU) +#define USB_OTG_FS_WAKEUP_EXTI_RISING_FALLING_EDGE ((uint32_t)0x10U) + +#define USB_OTG_HS_WAKEUP_EXTI_RISING_EDGE ((uint32_t)0x08U) +#define USB_OTG_HS_WAKEUP_EXTI_FALLING_EDGE ((uint32_t)0x0CU) +#define USB_OTG_HS_WAKEUP_EXTI_RISING_FALLING_EDGE ((uint32_t)0x10U) + +#define USB_OTG_HS_WAKEUP_EXTI_LINE ((uint32_t)0x00100000U) /*!< External interrupt line 20 Connected to the USB HS EXTI Line */ +#define USB_OTG_FS_WAKEUP_EXTI_LINE ((uint32_t)0x00040000U) /*!< External interrupt line 18 Connected to the USB FS EXTI Line */ + +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_ENABLE_IT() EXTI->IMR |= (USB_OTG_HS_WAKEUP_EXTI_LINE) +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_DISABLE_IT() EXTI->IMR &= ~(USB_OTG_HS_WAKEUP_EXTI_LINE) +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_GET_FLAG() EXTI->PR & (USB_OTG_HS_WAKEUP_EXTI_LINE) +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_CLEAR_FLAG() EXTI->PR = (USB_OTG_HS_WAKEUP_EXTI_LINE) + +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_ENABLE_RISING_EDGE() EXTI->FTSR &= ~(USB_OTG_HS_WAKEUP_EXTI_LINE);\ + EXTI->RTSR |= USB_OTG_HS_WAKEUP_EXTI_LINE + +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_ENABLE_FALLING_EDGE() EXTI->FTSR |= (USB_OTG_HS_WAKEUP_EXTI_LINE);\ + EXTI->RTSR &= ~(USB_OTG_HS_WAKEUP_EXTI_LINE) + +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_ENABLE_RISING_FALLING_EDGE() EXTI->RTSR &= ~(USB_OTG_HS_WAKEUP_EXTI_LINE);\ + EXTI->FTSR &= ~(USB_OTG_HS_WAKEUP_EXTI_LINE;)\ + EXTI->RTSR |= USB_OTG_HS_WAKEUP_EXTI_LINE;\ + EXTI->FTSR |= USB_OTG_HS_WAKEUP_EXTI_LINE + +#define __HAL_USB_OTG_HS_WAKEUP_EXTI_GENERATE_SWIT() (EXTI->SWIER |= USB_OTG_FS_WAKEUP_EXTI_LINE) + +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_ENABLE_IT() EXTI->IMR |= USB_OTG_FS_WAKEUP_EXTI_LINE +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_DISABLE_IT() EXTI->IMR &= ~(USB_OTG_FS_WAKEUP_EXTI_LINE) +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_GET_FLAG() EXTI->PR & (USB_OTG_FS_WAKEUP_EXTI_LINE) +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_CLEAR_FLAG() EXTI->PR = USB_OTG_FS_WAKEUP_EXTI_LINE + +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_ENABLE_RISING_EDGE() EXTI->FTSR &= ~(USB_OTG_FS_WAKEUP_EXTI_LINE);\ + EXTI->RTSR |= USB_OTG_FS_WAKEUP_EXTI_LINE + + +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_ENABLE_FALLING_EDGE() EXTI->FTSR |= (USB_OTG_FS_WAKEUP_EXTI_LINE);\ + EXTI->RTSR &= ~(USB_OTG_FS_WAKEUP_EXTI_LINE) + +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_ENABLE_RISING_FALLING_EDGE() EXTI->RTSR &= ~(USB_OTG_FS_WAKEUP_EXTI_LINE);\ + EXTI->FTSR &= ~(USB_OTG_FS_WAKEUP_EXTI_LINE);\ + EXTI->RTSR |= USB_OTG_FS_WAKEUP_EXTI_LINE;\ + EXTI->FTSR |= USB_OTG_FS_WAKEUP_EXTI_LINE + +#define __HAL_USB_OTG_FS_WAKEUP_EXTI_GENERATE_SWIT() (EXTI->SWIER |= USB_OTG_FS_WAKEUP_EXTI_LINE) +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup PCD_Exported_Functions PCD Exported Functions + * @{ + */ + +/* Initialization/de-initialization functions ********************************/ +/** @addtogroup PCD_Exported_Functions_Group1 Initialization and de-initialization functions + * @{ + */ +HAL_StatusTypeDef HAL_PCD_Init(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCD_DeInit (PCD_HandleTypeDef *hpcd); +void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd); +void HAL_PCD_MspDeInit(PCD_HandleTypeDef *hpcd); +/** + * @} + */ + +/* I/O operation functions ***************************************************/ +/* Non-Blocking mode: Interrupt */ +/** @addtogroup PCD_Exported_Functions_Group2 Input and Output operation functions + * @{ + */ +HAL_StatusTypeDef HAL_PCD_Start(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCD_Stop(PCD_HandleTypeDef *hpcd); +void HAL_PCD_IRQHandler(PCD_HandleTypeDef *hpcd); + +void HAL_PCD_DataOutStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum); +void HAL_PCD_DataInStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum); +void HAL_PCD_SetupStageCallback(PCD_HandleTypeDef *hpcd); +void HAL_PCD_SOFCallback(PCD_HandleTypeDef *hpcd); +void HAL_PCD_ResetCallback(PCD_HandleTypeDef *hpcd); +void HAL_PCD_SuspendCallback(PCD_HandleTypeDef *hpcd); +void HAL_PCD_ResumeCallback(PCD_HandleTypeDef *hpcd); +void HAL_PCD_ISOOUTIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum); +void HAL_PCD_ISOINIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum); +void HAL_PCD_ConnectCallback(PCD_HandleTypeDef *hpcd); +void HAL_PCD_DisconnectCallback(PCD_HandleTypeDef *hpcd); +/** + * @} + */ + +/* Peripheral Control functions **********************************************/ +/** @addtogroup PCD_Exported_Functions_Group3 Peripheral Control functions + * @{ + */ +HAL_StatusTypeDef HAL_PCD_DevConnect(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCD_DevDisconnect(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCD_SetAddress(PCD_HandleTypeDef *hpcd, uint8_t address); +HAL_StatusTypeDef HAL_PCD_EP_Open(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, uint16_t ep_mps, uint8_t ep_type); +HAL_StatusTypeDef HAL_PCD_EP_Close(PCD_HandleTypeDef *hpcd, uint8_t ep_addr); +HAL_StatusTypeDef HAL_PCD_EP_Receive(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, uint8_t *pBuf, uint32_t len); +HAL_StatusTypeDef HAL_PCD_EP_Transmit(PCD_HandleTypeDef *hpcd, uint8_t ep_addr, uint8_t *pBuf, uint32_t len); +uint16_t HAL_PCD_EP_GetRxCount(PCD_HandleTypeDef *hpcd, uint8_t ep_addr); +HAL_StatusTypeDef HAL_PCD_EP_SetStall(PCD_HandleTypeDef *hpcd, uint8_t ep_addr); +HAL_StatusTypeDef HAL_PCD_EP_ClrStall(PCD_HandleTypeDef *hpcd, uint8_t ep_addr); +HAL_StatusTypeDef HAL_PCD_EP_Flush(PCD_HandleTypeDef *hpcd, uint8_t ep_addr); +HAL_StatusTypeDef HAL_PCD_ActivateRemoteWakeup(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCD_DeActivateRemoteWakeup(PCD_HandleTypeDef *hpcd); +/** + * @} + */ + +/* Peripheral State functions ************************************************/ +/** @addtogroup PCD_Exported_Functions_Group4 Peripheral State functions + * @{ + */ +PCD_StateTypeDef HAL_PCD_GetState(PCD_HandleTypeDef *hpcd); +/** + * @} + */ + +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup PCD_Private_Macros PCD Private Macros + * @{ + */ +/** @defgroup PCD_Instance_definition PCD Instance definition + * @{ + */ +#define IS_PCD_ALL_INSTANCE(INSTANCE) (((INSTANCE) == USB_OTG_FS) || \ + ((INSTANCE) == USB_OTG_HS)) +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* __STM32F7xx_HAL_PCD_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
http://git-wip-us.apache.org/repos/asf/incubator-mynewt-core/blob/35529b95/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd_ex.h ---------------------------------------------------------------------- diff --git a/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd_ex.h b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd_ex.h new file mode 100644 index 0000000..3b37abb --- /dev/null +++ b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pcd_ex.h @@ -0,0 +1,116 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_pcd_ex.h + * @author MCD Application Team + * @version V1.2.0 + * @date 30-December-2016 + * @brief Header file of PCD HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_PCD_EX_H +#define __STM32F7xx_HAL_PCD_EX_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal_def.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @addtogroup PCDEx + * @{ + */ +/* Exported types ------------------------------------------------------------*/ +typedef enum +{ + PCD_LPM_L0_ACTIVE = 0x00U, /* on */ + PCD_LPM_L1_ACTIVE = 0x01U, /* LPM L1 sleep */ +}PCD_LPM_MsgTypeDef; + +typedef enum +{ + PCD_BCD_ERROR = 0xFF, + PCD_BCD_CONTACT_DETECTION = 0xFE, + PCD_BCD_STD_DOWNSTREAM_PORT = 0xFD, + PCD_BCD_CHARGING_DOWNSTREAM_PORT = 0xFC, + PCD_BCD_DEDICATED_CHARGING_PORT = 0xFB, + PCD_BCD_DISCOVERY_COMPLETED = 0x00, + +}PCD_BCD_MsgTypeDef; + +/* Exported constants --------------------------------------------------------*/ +/* Exported macros -----------------------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup PCDEx_Exported_Functions PCDEx Exported Functions + * @{ + */ +/** @addtogroup PCDEx_Exported_Functions_Group1 Peripheral Control functions + * @{ + */ +HAL_StatusTypeDef HAL_PCDEx_SetTxFiFo(PCD_HandleTypeDef *hpcd, uint8_t fifo, uint16_t size); +HAL_StatusTypeDef HAL_PCDEx_SetRxFiFo(PCD_HandleTypeDef *hpcd, uint16_t size); +HAL_StatusTypeDef HAL_PCDEx_ActivateLPM(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCDEx_DeActivateLPM(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCDEx_ActivateBCD(PCD_HandleTypeDef *hpcd); +HAL_StatusTypeDef HAL_PCDEx_DeActivateBCD(PCD_HandleTypeDef *hpcd); +void HAL_PCDEx_BCD_VBUSDetect(PCD_HandleTypeDef *hpcd); +void HAL_PCDEx_LPM_Callback(PCD_HandleTypeDef *hpcd, PCD_LPM_MsgTypeDef msg); +void HAL_PCDEx_BCD_Callback(PCD_HandleTypeDef *hpcd, PCD_BCD_MsgTypeDef msg); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* __STM32F7xx_HAL_PCD_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ http://git-wip-us.apache.org/repos/asf/incubator-mynewt-core/blob/35529b95/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr.h ---------------------------------------------------------------------- diff --git a/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr.h b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr.h new file mode 100644 index 0000000..08b034b --- /dev/null +++ b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr.h @@ -0,0 +1,422 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_pwr.h + * @author MCD Application Team + * @version V1.2.0 + * @date 30-December-2016 + * @brief Header file of PWR HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_PWR_H +#define __STM32F7xx_HAL_PWR_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal_def.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @addtogroup PWR + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup PWR_Exported_Types PWR Exported Types + * @{ + */ + +/** + * @brief PWR PVD configuration structure definition + */ +typedef struct +{ + uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level. + This parameter can be a value of @ref PWR_PVD_detection_level */ + + uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins. + This parameter can be a value of @ref PWR_PVD_Mode */ +}PWR_PVDTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup PWR_Exported_Constants PWR Exported Constants + * @{ + */ + +/** @defgroup PWR_PVD_detection_level PWR PVD detection level + * @{ + */ +#define PWR_PVDLEVEL_0 PWR_CR1_PLS_LEV0 +#define PWR_PVDLEVEL_1 PWR_CR1_PLS_LEV1 +#define PWR_PVDLEVEL_2 PWR_CR1_PLS_LEV2 +#define PWR_PVDLEVEL_3 PWR_CR1_PLS_LEV3 +#define PWR_PVDLEVEL_4 PWR_CR1_PLS_LEV4 +#define PWR_PVDLEVEL_5 PWR_CR1_PLS_LEV5 +#define PWR_PVDLEVEL_6 PWR_CR1_PLS_LEV6 +#define PWR_PVDLEVEL_7 PWR_CR1_PLS_LEV7/* External input analog voltage + (Compare internally to VREFINT) */ + +/** + * @} + */ + +/** @defgroup PWR_PVD_Mode PWR PVD Mode + * @{ + */ +#define PWR_PVD_MODE_NORMAL ((uint32_t)0x00000000U) /*!< basic mode is used */ +#define PWR_PVD_MODE_IT_RISING ((uint32_t)0x00010001U) /*!< External Interrupt Mode with Rising edge trigger detection */ +#define PWR_PVD_MODE_IT_FALLING ((uint32_t)0x00010002U) /*!< External Interrupt Mode with Falling edge trigger detection */ +#define PWR_PVD_MODE_IT_RISING_FALLING ((uint32_t)0x00010003U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */ +#define PWR_PVD_MODE_EVENT_RISING ((uint32_t)0x00020001U) /*!< Event Mode with Rising edge trigger detection */ +#define PWR_PVD_MODE_EVENT_FALLING ((uint32_t)0x00020002U) /*!< Event Mode with Falling edge trigger detection */ +#define PWR_PVD_MODE_EVENT_RISING_FALLING ((uint32_t)0x00020003U) /*!< Event Mode with Rising/Falling edge trigger detection */ +/** + * @} + */ + +/** @defgroup PWR_Regulator_state_in_STOP_mode PWR Regulator state in SLEEP/STOP mode + * @{ + */ +#define PWR_MAINREGULATOR_ON ((uint32_t)0x00000000U) +#define PWR_LOWPOWERREGULATOR_ON PWR_CR1_LPDS +/** + * @} + */ + +/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry + * @{ + */ +#define PWR_SLEEPENTRY_WFI ((uint8_t)0x01U) +#define PWR_SLEEPENTRY_WFE ((uint8_t)0x02U) +/** + * @} + */ + +/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry + * @{ + */ +#define PWR_STOPENTRY_WFI ((uint8_t)0x01U) +#define PWR_STOPENTRY_WFE ((uint8_t)0x02U) +/** + * @} + */ + +/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale + * @{ + */ +#define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR1_VOS +#define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR1_VOS_1 +#define PWR_REGULATOR_VOLTAGE_SCALE3 PWR_CR1_VOS_0 +/** + * @} + */ + +/** @defgroup PWR_Flag PWR Flag + * @{ + */ +#define PWR_FLAG_WU PWR_CSR1_WUIF +#define PWR_FLAG_SB PWR_CSR1_SBF +#define PWR_FLAG_PVDO PWR_CSR1_PVDO +#define PWR_FLAG_BRR PWR_CSR1_BRR +#define PWR_FLAG_VOSRDY PWR_CSR1_VOSRDY +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup PWR_Exported_Macro PWR Exported Macro + * @{ + */ + +/** @brief macros configure the main internal regulator output voltage. + * @param __REGULATOR__: specifies the regulator output voltage to achieve + * a tradeoff between performance and power consumption when the device does + * not operate at the maximum frequency (refer to the datasheets for more details). + * This parameter can be one of the following values: + * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode + * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode + * @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode + * @retval None + */ +#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do { \ + __IO uint32_t tmpreg; \ + MODIFY_REG(PWR->CR1, PWR_CR1_VOS, (__REGULATOR__)); \ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(PWR->CR1, PWR_CR1_VOS); \ + UNUSED(tmpreg); \ + } while(0) + +/** @brief Check PWR flag is set or not. + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event + * was received on the internal wakeup line in standby mode (RTC alarm (Alarm A or Alarm B), + * RTC Tamper event, RTC TimeStamp event or RTC Wakeup)). + * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was + * resumed from StandBy mode. + * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled + * by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode + * For this reason, this bit is equal to 0 after Standby or reset + * until the PVDE bit is set. + * @arg PWR_FLAG_BRR: Backup regulator ready flag. This bit is not reset + * when the device wakes up from Standby mode or by a system reset + * or power reset. + * @arg PWR_FLAG_VOSRDY: This flag indicates that the Regulator voltage + * scaling output selection is ready. + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR1 & (__FLAG__)) == (__FLAG__)) + +/** @brief Clear the PWR's pending flags. + * @param __FLAG__: specifies the flag to clear. + * This parameter can be one of the following values: + * @arg PWR_FLAG_SB: StandBy flag + */ +#define __HAL_PWR_CLEAR_FLAG(__FLAG__) (PWR->CR1 |= (__FLAG__) << 2) + +/** + * @brief Enable the PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_IT() (EXTI->IMR |= (PWR_EXTI_LINE_PVD)) + +/** + * @brief Disable the PVD EXTI Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_IT() (EXTI->IMR &= ~(PWR_EXTI_LINE_PVD)) + +/** + * @brief Enable event on PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() (EXTI->EMR |= (PWR_EXTI_LINE_PVD)) + +/** + * @brief Disable event on PVD Exti Line 16. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() (EXTI->EMR &= ~(PWR_EXTI_LINE_PVD)) + +/** + * @brief Enable the PVD Extended Interrupt Rising Trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) + +/** + * @brief Disable the PVD Extended Interrupt Rising Trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD) + +/** + * @brief Enable the PVD Extended Interrupt Falling Trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) + + +/** + * @brief Disable the PVD Extended Interrupt Falling Trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD) + + +/** + * @brief PVD EXTI line configuration: set rising & falling edge trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); + +/** + * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); + +/** + * @brief checks whether the specified PVD Exti interrupt flag is set or not. + * @retval EXTI PVD Line Status. + */ +#define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD)) + +/** + * @brief Clear the PVD Exti flag. + * @retval None. + */ +#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD)) + +/** + * @brief Generates a Software interrupt on PVD EXTI line. + * @retval None + */ +#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() (EXTI->SWIER |= (PWR_EXTI_LINE_PVD)) + +/** + * @} + */ + +/* Include PWR HAL Extension module */ +#include "stm32f7xx_hal_pwr_ex.h" + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup PWR_Exported_Functions PWR Exported Functions + * @{ + */ + +/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions + * @{ + */ +/* Initialization and de-initialization functions *****************************/ +void HAL_PWR_DeInit(void); +void HAL_PWR_EnableBkUpAccess(void); +void HAL_PWR_DisableBkUpAccess(void); +/** + * @} + */ + +/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions + * @{ + */ +/* Peripheral Control functions **********************************************/ +/* PVD configuration */ +void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD); +void HAL_PWR_EnablePVD(void); +void HAL_PWR_DisablePVD(void); + +/* WakeUp pins configuration */ +void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinPolarity); +void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx); + +/* Low Power modes entry */ +void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry); +void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry); +void HAL_PWR_EnterSTANDBYMode(void); + +/* Power PVD IRQ Handler */ +void HAL_PWR_PVD_IRQHandler(void); +void HAL_PWR_PVDCallback(void); + +/* Cortex System Control functions *******************************************/ +void HAL_PWR_EnableSleepOnExit(void); +void HAL_PWR_DisableSleepOnExit(void); +void HAL_PWR_EnableSEVOnPend(void); +void HAL_PWR_DisableSEVOnPend(void); +/** + * @} + */ + +/** + * @} + */ + +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private constants ---------------------------------------------------------*/ +/** @defgroup PWR_Private_Constants PWR Private Constants + * @{ + */ + +/** @defgroup PWR_PVD_EXTI_Line PWR PVD EXTI Line + * @{ + */ +#define PWR_EXTI_LINE_PVD ((uint32_t)EXTI_IMR_IM16) /*!< External interrupt line 16 Connected to the PVD EXTI Line */ +/** + * @} + */ + +/** + * @} + */ +/* Private macros ------------------------------------------------------------*/ +/** @defgroup PWR_Private_Macros PWR Private Macros + * @{ + */ + +/** @defgroup PWR_IS_PWR_Definitions PWR Private macros to check input parameters + * @{ + */ +#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \ + ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \ + ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \ + ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7)) +#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \ + ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \ + ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \ + ((MODE) == PWR_PVD_MODE_NORMAL)) +#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \ + ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON)) +#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE)) +#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE)) +#define IS_PWR_REGULATOR_VOLTAGE(VOLTAGE) (((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \ + ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \ + ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE3)) + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* __STM32F7xx_HAL_PWR_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ http://git-wip-us.apache.org/repos/asf/incubator-mynewt-core/blob/35529b95/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr_ex.h ---------------------------------------------------------------------- diff --git a/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr_ex.h b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr_ex.h new file mode 100644 index 0000000..072719a --- /dev/null +++ b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_pwr_ex.h @@ -0,0 +1,280 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_pwr_ex.h + * @author MCD Application Team + * @version V1.2.0 + * @date 30-December-2016 + * @brief Header file of PWR HAL Extension module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_PWR_EX_H +#define __STM32F7xx_HAL_PWR_EX_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal_def.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @addtogroup PWREx + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ +/** @defgroup PWREx_Exported_Constants PWREx Exported Constants + * @{ + */ +/** @defgroup PWREx_WakeUp_Pins PWREx Wake Up Pins + * @{ + */ +#define PWR_WAKEUP_PIN1 PWR_CSR2_EWUP1 +#define PWR_WAKEUP_PIN2 PWR_CSR2_EWUP2 +#define PWR_WAKEUP_PIN3 PWR_CSR2_EWUP3 +#define PWR_WAKEUP_PIN4 PWR_CSR2_EWUP4 +#define PWR_WAKEUP_PIN5 PWR_CSR2_EWUP5 +#define PWR_WAKEUP_PIN6 PWR_CSR2_EWUP6 +#define PWR_WAKEUP_PIN1_HIGH PWR_CSR2_EWUP1 +#define PWR_WAKEUP_PIN2_HIGH PWR_CSR2_EWUP2 +#define PWR_WAKEUP_PIN3_HIGH PWR_CSR2_EWUP3 +#define PWR_WAKEUP_PIN4_HIGH PWR_CSR2_EWUP4 +#define PWR_WAKEUP_PIN5_HIGH PWR_CSR2_EWUP5 +#define PWR_WAKEUP_PIN6_HIGH PWR_CSR2_EWUP6 +#define PWR_WAKEUP_PIN1_LOW (uint32_t)((PWR_CR2_WUPP1<<6) | PWR_CSR2_EWUP1) +#define PWR_WAKEUP_PIN2_LOW (uint32_t)((PWR_CR2_WUPP2<<6) | PWR_CSR2_EWUP2) +#define PWR_WAKEUP_PIN3_LOW (uint32_t)((PWR_CR2_WUPP3<<6) | PWR_CSR2_EWUP3) +#define PWR_WAKEUP_PIN4_LOW (uint32_t)((PWR_CR2_WUPP4<<6) | PWR_CSR2_EWUP4) +#define PWR_WAKEUP_PIN5_LOW (uint32_t)((PWR_CR2_WUPP5<<6) | PWR_CSR2_EWUP5) +#define PWR_WAKEUP_PIN6_LOW (uint32_t)((PWR_CR2_WUPP6<<6) | PWR_CSR2_EWUP6) + +/** + * @} + */ + +/** @defgroup PWREx_Regulator_state_in_UnderDrive_mode PWREx Regulator state in UnderDrive mode + * @{ + */ +#define PWR_MAINREGULATOR_UNDERDRIVE_ON PWR_CR1_MRUDS +#define PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON ((uint32_t)(PWR_CR1_LPDS | PWR_CR1_LPUDS)) +/** + * @} + */ + +/** @defgroup PWREx_Over_Under_Drive_Flag PWREx Over Under Drive Flag + * @{ + */ +#define PWR_FLAG_ODRDY PWR_CSR1_ODRDY +#define PWR_FLAG_ODSWRDY PWR_CSR1_ODSWRDY +#define PWR_FLAG_UDRDY PWR_CSR1_UDRDY +/** + * @} + */ + +/** @defgroup PWREx_Wakeup_Pins_Flag PWREx Wake Up Pin Flags + * @{ + */ +#define PWR_WAKEUP_PIN_FLAG1 PWR_CSR2_WUPF1 +#define PWR_WAKEUP_PIN_FLAG2 PWR_CSR2_WUPF2 +#define PWR_WAKEUP_PIN_FLAG3 PWR_CSR2_WUPF3 +#define PWR_WAKEUP_PIN_FLAG4 PWR_CSR2_WUPF4 +#define PWR_WAKEUP_PIN_FLAG5 PWR_CSR2_WUPF5 +#define PWR_WAKEUP_PIN_FLAG6 PWR_CSR2_WUPF6 +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup PWREx_Exported_Macro PWREx Exported Macro + * @{ + */ +/** @brief Macros to enable or disable the Over drive mode. + */ +#define __HAL_PWR_OVERDRIVE_ENABLE() (PWR->CR1 |= (uint32_t)PWR_CR1_ODEN) +#define __HAL_PWR_OVERDRIVE_DISABLE() (PWR->CR1 &= (uint32_t)(~PWR_CR1_ODEN)) + +/** @brief Macros to enable or disable the Over drive switching. + */ +#define __HAL_PWR_OVERDRIVESWITCHING_ENABLE() (PWR->CR1 |= (uint32_t)PWR_CR1_ODSWEN) +#define __HAL_PWR_OVERDRIVESWITCHING_DISABLE() (PWR->CR1 &= (uint32_t)(~PWR_CR1_ODSWEN)) + +/** @brief Macros to enable or disable the Under drive mode. + * @note This mode is enabled only with STOP low power mode. + * In this mode, the 1.2V domain is preserved in reduced leakage mode. This + * mode is only available when the main regulator or the low power regulator + * is in low voltage mode. + * @note If the Under-drive mode was enabled, it is automatically disabled after + * exiting Stop mode. + * When the voltage regulator operates in Under-drive mode, an additional + * startup delay is induced when waking up from Stop mode. + */ +#define __HAL_PWR_UNDERDRIVE_ENABLE() (PWR->CR1 |= (uint32_t)PWR_CR1_UDEN) +#define __HAL_PWR_UNDERDRIVE_DISABLE() (PWR->CR1 &= (uint32_t)(~PWR_CR1_UDEN)) + +/** @brief Check PWR flag is set or not. + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg PWR_FLAG_ODRDY: This flag indicates that the Over-drive mode + * is ready + * @arg PWR_FLAG_ODSWRDY: This flag indicates that the Over-drive mode + * switching is ready + * @arg PWR_FLAG_UDRDY: This flag indicates that the Under-drive mode + * is enabled in Stop mode + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_PWR_GET_ODRUDR_FLAG(__FLAG__) ((PWR->CSR1 & (__FLAG__)) == (__FLAG__)) + +/** @brief Clear the Under-Drive Ready flag. + */ +#define __HAL_PWR_CLEAR_ODRUDR_FLAG() (PWR->CSR1 |= PWR_FLAG_UDRDY) + +/** @brief Check Wake Up flag is set or not. + * @param __WUFLAG__: specifies the Wake Up flag to check. + * This parameter can be one of the following values: + * @arg PWR_WAKEUP_PIN_FLAG1: Wakeup Pin Flag for PA0 + * @arg PWR_WAKEUP_PIN_FLAG2: Wakeup Pin Flag for PA2 + * @arg PWR_WAKEUP_PIN_FLAG3: Wakeup Pin Flag for PC1 + * @arg PWR_WAKEUP_PIN_FLAG4: Wakeup Pin Flag for PC13 + * @arg PWR_WAKEUP_PIN_FLAG5: Wakeup Pin Flag for PI8 + * @arg PWR_WAKEUP_PIN_FLAG6: Wakeup Pin Flag for PI11 + */ +#define __HAL_PWR_GET_WAKEUP_FLAG(__WUFLAG__) (PWR->CSR2 & (__WUFLAG__)) + +/** @brief Clear the WakeUp pins flags. + * @param __WUFLAG__: specifies the Wake Up pin flag to clear. + * This parameter can be one of the following values: + * @arg PWR_WAKEUP_PIN_FLAG1: Wakeup Pin Flag for PA0 + * @arg PWR_WAKEUP_PIN_FLAG2: Wakeup Pin Flag for PA2 + * @arg PWR_WAKEUP_PIN_FLAG3: Wakeup Pin Flag for PC1 + * @arg PWR_WAKEUP_PIN_FLAG4: Wakeup Pin Flag for PC13 + * @arg PWR_WAKEUP_PIN_FLAG5: Wakeup Pin Flag for PI8 + * @arg PWR_WAKEUP_PIN_FLAG6: Wakeup Pin Flag for PI11 + */ +#define __HAL_PWR_CLEAR_WAKEUP_FLAG(__WUFLAG__) (PWR->CR2 |= (__WUFLAG__)) +/** + * @} + */ +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup PWREx_Exported_Functions PWREx Exported Functions + * @{ + */ + +/** @addtogroup PWREx_Exported_Functions_Group1 + * @{ + */ +uint32_t HAL_PWREx_GetVoltageRange(void); +HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling); + +void HAL_PWREx_EnableFlashPowerDown(void); +void HAL_PWREx_DisableFlashPowerDown(void); +HAL_StatusTypeDef HAL_PWREx_EnableBkUpReg(void); +HAL_StatusTypeDef HAL_PWREx_DisableBkUpReg(void); + +void HAL_PWREx_EnableMainRegulatorLowVoltage(void); +void HAL_PWREx_DisableMainRegulatorLowVoltage(void); +void HAL_PWREx_EnableLowRegulatorLowVoltage(void); +void HAL_PWREx_DisableLowRegulatorLowVoltage(void); + +HAL_StatusTypeDef HAL_PWREx_EnableOverDrive(void); +HAL_StatusTypeDef HAL_PWREx_DisableOverDrive(void); +HAL_StatusTypeDef HAL_PWREx_EnterUnderDriveSTOPMode(uint32_t Regulator, uint8_t STOPEntry); + +/** + * @} + */ + +/** + * @} + */ +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private constants ---------------------------------------------------------*/ +/* Private macros ------------------------------------------------------------*/ +/** @defgroup PWREx_Private_Macros PWREx Private Macros + * @{ + */ + +/** @defgroup PWREx_IS_PWR_Definitions PWREx Private macros to check input parameters + * @{ + */ +#define IS_PWR_REGULATOR_UNDERDRIVE(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_UNDERDRIVE_ON) || \ + ((REGULATOR) == PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON)) +#define IS_PWR_WAKEUP_PIN(__PIN__) (((__PIN__) == PWR_WAKEUP_PIN1) || \ + ((__PIN__) == PWR_WAKEUP_PIN2) || \ + ((__PIN__) == PWR_WAKEUP_PIN3) || \ + ((__PIN__) == PWR_WAKEUP_PIN4) || \ + ((__PIN__) == PWR_WAKEUP_PIN5) || \ + ((__PIN__) == PWR_WAKEUP_PIN6) || \ + ((__PIN__) == PWR_WAKEUP_PIN1_HIGH) || \ + ((__PIN__) == PWR_WAKEUP_PIN2_HIGH) || \ + ((__PIN__) == PWR_WAKEUP_PIN3_HIGH) || \ + ((__PIN__) == PWR_WAKEUP_PIN4_HIGH) || \ + ((__PIN__) == PWR_WAKEUP_PIN5_HIGH) || \ + ((__PIN__) == PWR_WAKEUP_PIN6_HIGH) || \ + ((__PIN__) == PWR_WAKEUP_PIN1_LOW) || \ + ((__PIN__) == PWR_WAKEUP_PIN2_LOW) || \ + ((__PIN__) == PWR_WAKEUP_PIN3_LOW) || \ + ((__PIN__) == PWR_WAKEUP_PIN4_LOW) || \ + ((__PIN__) == PWR_WAKEUP_PIN5_LOW) || \ + ((__PIN__) == PWR_WAKEUP_PIN6_LOW)) +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + + +#endif /* __STM32F7xx_HAL_PWR_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ http://git-wip-us.apache.org/repos/asf/incubator-mynewt-core/blob/35529b95/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_qspi.h ---------------------------------------------------------------------- diff --git a/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_qspi.h b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_qspi.h new file mode 100644 index 0000000..89d7e03 --- /dev/null +++ b/hw/mcu/stm/stm32f7xx/src/ext/Drivers/STM32F7xx_HAL_Driver/Inc/stm32f7xx_hal_qspi.h @@ -0,0 +1,781 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_qspi.h + * @author MCD Application Team + * @version V1.2.0 + * @date 30-December-2016 + * @brief Header file of QSPI HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_QSPI_H +#define __STM32F7xx_HAL_QSPI_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal_def.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @addtogroup QSPI + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup QSPI_Exported_Types QSPI Exported Types + * @{ + */ + +/** + * @brief QSPI Init structure definition + */ + +typedef struct +{ + uint32_t ClockPrescaler; /* Specifies the prescaler factor for generating clock based on the AHB clock. + This parameter can be a number between 0 and 255 */ + + uint32_t FifoThreshold; /* Specifies the threshold number of bytes in the FIFO (used only in indirect mode) + This parameter can be a value between 1 and 32 */ + + uint32_t SampleShifting; /* Specifies the Sample Shift. The data is sampled 1/2 clock cycle delay later to + take in account external signal delays. (It should be QSPI_SAMPLE_SHIFTING_NONE in DDR mode) + This parameter can be a value of @ref QSPI_SampleShifting */ + + uint32_t FlashSize; /* Specifies the Flash Size. FlashSize+1 is effectively the number of address bits + required to address the flash memory. The flash capacity can be up to 4GB + (addressed using 32 bits) in indirect mode, but the addressable space in + memory-mapped mode is limited to 256MB + This parameter can be a number between 0 and 31 */ + + uint32_t ChipSelectHighTime; /* Specifies the Chip Select High Time. ChipSelectHighTime+1 defines the minimum number + of clock cycles which the chip select must remain high between commands. + This parameter can be a value of @ref QSPI_ChipSelectHighTime */ + + uint32_t ClockMode; /* Specifies the Clock Mode. It indicates the level that clock takes between commands. + This parameter can be a value of @ref QSPI_ClockMode */ + + uint32_t FlashID; /* Specifies the Flash which will be used, + This parameter can be a value of @ref QSPI_Flash_Select */ + + uint32_t DualFlash; /* Specifies the Dual Flash Mode State + This parameter can be a value of @ref QSPI_DualFlash_Mode */ +}QSPI_InitTypeDef; + +/** + * @brief HAL QSPI State structures definition + */ +typedef enum +{ + HAL_QSPI_STATE_RESET = 0x00U, /*!< Peripheral not initialized */ + HAL_QSPI_STATE_READY = 0x01U, /*!< Peripheral initialized and ready for use */ + HAL_QSPI_STATE_BUSY = 0x02U, /*!< Peripheral in indirect mode and busy */ + HAL_QSPI_STATE_BUSY_INDIRECT_TX = 0x12U, /*!< Peripheral in indirect mode with transmission ongoing */ + HAL_QSPI_STATE_BUSY_INDIRECT_RX = 0x22U, /*!< Peripheral in indirect mode with reception ongoing */ + HAL_QSPI_STATE_BUSY_AUTO_POLLING = 0x42U, /*!< Peripheral in auto polling mode ongoing */ + HAL_QSPI_STATE_BUSY_MEM_MAPPED = 0x82U, /*!< Peripheral in memory mapped mode ongoing */ + HAL_QSPI_STATE_ABORT = 0x08U, /*!< Peripheral with abort request ongoing */ + HAL_QSPI_STATE_ERROR = 0x04U /*!< Peripheral in error */ +}HAL_QSPI_StateTypeDef; + +/** + * @brief QSPI Handle Structure definition + */ +typedef struct +{ + QUADSPI_TypeDef *Instance; /* QSPI registers base address */ + QSPI_InitTypeDef Init; /* QSPI communication parameters */ + uint8_t *pTxBuffPtr; /* Pointer to QSPI Tx transfer Buffer */ + __IO uint32_t TxXferSize; /* QSPI Tx Transfer size */ + __IO uint32_t TxXferCount; /* QSPI Tx Transfer Counter */ + uint8_t *pRxBuffPtr; /* Pointer to QSPI Rx transfer Buffer */ + __IO uint32_t RxXferSize; /* QSPI Rx Transfer size */ + __IO uint32_t RxXferCount; /* QSPI Rx Transfer Counter */ + DMA_HandleTypeDef *hdma; /* QSPI Rx/Tx DMA Handle parameters */ + __IO HAL_LockTypeDef Lock; /* Locking object */ + __IO HAL_QSPI_StateTypeDef State; /* QSPI communication state */ + __IO uint32_t ErrorCode; /* QSPI Error code */ + uint32_t Timeout; /* Timeout for the QSPI memory access */ +}QSPI_HandleTypeDef; + +/** + * @brief QSPI Command structure definition + */ +typedef struct +{ + uint32_t Instruction; /* Specifies the Instruction to be sent + This parameter can be a value (8-bit) between 0x00 and 0xFF */ + uint32_t Address; /* Specifies the Address to be sent (Size from 1 to 4 bytes according AddressSize) + This parameter can be a value (32-bits) between 0x0 and 0xFFFFFFFF */ + uint32_t AlternateBytes; /* Specifies the Alternate Bytes to be sent (Size from 1 to 4 bytes according AlternateBytesSize) + This parameter can be a value (32-bits) between 0x0 and 0xFFFFFFFF */ + uint32_t AddressSize; /* Specifies the Address Size + This parameter can be a value of @ref QSPI_AddressSize */ + uint32_t AlternateBytesSize; /* Specifies the Alternate Bytes Size + This parameter can be a value of @ref QSPI_AlternateBytesSize */ + uint32_t DummyCycles; /* Specifies the Number of Dummy Cycles. + This parameter can be a number between 0 and 31 */ + uint32_t InstructionMode; /* Specifies the Instruction Mode + This parameter can be a value of @ref QSPI_InstructionMode */ + uint32_t AddressMode; /* Specifies the Address Mode + This parameter can be a value of @ref QSPI_AddressMode */ + uint32_t AlternateByteMode; /* Specifies the Alternate Bytes Mode + This parameter can be a value of @ref QSPI_AlternateBytesMode */ + uint32_t DataMode; /* Specifies the Data Mode (used for dummy cycles and data phases) + This parameter can be a value of @ref QSPI_DataMode */ + uint32_t NbData; /* Specifies the number of data to transfer. + This parameter can be any value between 0 and 0xFFFFFFFF (0 means undefined length + until end of memory)*/ + uint32_t DdrMode; /* Specifies the double data rate mode for address, alternate byte and data phase + This parameter can be a value of @ref QSPI_DdrMode */ + uint32_t DdrHoldHalfCycle; /* Specifies the DDR hold half cycle. It delays the data output by one half of + system clock in DDR mode. + This parameter can be a value of @ref QSPI_DdrHoldHalfCycle */ + uint32_t SIOOMode; /* Specifies the send instruction only once mode + This parameter can be a value of @ref QSPI_SIOOMode */ +}QSPI_CommandTypeDef; + +/** + * @brief QSPI Auto Polling mode configuration structure definition + */ +typedef struct +{ + uint32_t Match; /* Specifies the value to be compared with the masked status register to get a match. + This parameter can be any value between 0 and 0xFFFFFFFF */ + uint32_t Mask; /* Specifies the mask to be applied to the status bytes received. + This parameter can be any value between 0 and 0xFFFFFFFF */ + uint32_t Interval; /* Specifies the number of clock cycles between two read during automatic polling phases. + This parameter can be any value between 0 and 0xFFFF */ + uint32_t StatusBytesSize; /* Specifies the size of the status bytes received. + This parameter can be any value between 1 and 4 */ + uint32_t MatchMode; /* Specifies the method used for determining a match. + This parameter can be a value of @ref QSPI_MatchMode */ + uint32_t AutomaticStop; /* Specifies if automatic polling is stopped after a match. + This parameter can be a value of @ref QSPI_AutomaticStop */ +}QSPI_AutoPollingTypeDef; + +/** + * @brief QSPI Memory Mapped mode configuration structure definition + */ +typedef struct +{ + uint32_t TimeOutPeriod; /* Specifies the number of clock to wait when the FIFO is full before to release the chip select. + This parameter can be any value between 0 and 0xFFFF */ + uint32_t TimeOutActivation; /* Specifies if the time out counter is enabled to release the chip select. + This parameter can be a value of @ref QSPI_TimeOutActivation */ +}QSPI_MemoryMappedTypeDef; +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup QSPI_Exported_Constants QSPI Exported Constants + * @{ + */ +/** @defgroup QSPI_ErrorCode QSPI Error Code + * @{ + */ +#define HAL_QSPI_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */ +#define HAL_QSPI_ERROR_TIMEOUT ((uint32_t)0x00000001U) /*!< Timeout error */ +#define HAL_QSPI_ERROR_TRANSFER ((uint32_t)0x00000002U) /*!< Transfer error */ +#define HAL_QSPI_ERROR_DMA ((uint32_t)0x00000004U) /*!< DMA transfer error */ +#define HAL_QSPI_ERROR_INVALID_PARAM ((uint32_t)0x00000008U) /*!< Invalid parameters error */ +/** + * @} + */ + +/** @defgroup QSPI_SampleShifting QSPI Sample Shifting + * @{ + */ +#define QSPI_SAMPLE_SHIFTING_NONE ((uint32_t)0x00000000U) /*!<No clock cycle shift to sample data*/ +#define QSPI_SAMPLE_SHIFTING_HALFCYCLE ((uint32_t)QUADSPI_CR_SSHIFT) /*!<1/2 clock cycle shift to sample data*/ +/** + * @} + */ + +/** @defgroup QSPI_ChipSelectHighTime QSPI Chip Select High Time + * @{ + */ +#define QSPI_CS_HIGH_TIME_1_CYCLE ((uint32_t)0x00000000U) /*!<nCS stay high for at least 1 clock cycle between commands*/ +#define QSPI_CS_HIGH_TIME_2_CYCLE ((uint32_t)QUADSPI_DCR_CSHT_0) /*!<nCS stay high for at least 2 clock cycles between commands*/ +#define QSPI_CS_HIGH_TIME_3_CYCLE ((uint32_t)QUADSPI_DCR_CSHT_1) /*!<nCS stay high for at least 3 clock cycles between commands*/ +#define QSPI_CS_HIGH_TIME_4_CYCLE ((uint32_t)QUADSPI_DCR_CSHT_0 | QUADSPI_DCR_CSHT_1) /*!<nCS stay high for at least 4 clock cycles between commands*/ +#define QSPI_CS_HIGH_TIME_5_CYCLE ((uint32_t)QUADSPI_DCR_CSHT_2) /*!<nCS stay high for at least 5 clock cycles between commands*/ +#define QSPI_CS_HIGH_TIME_6_CYCLE ((uint32_t)QUADSPI_DCR_CSHT_2 | QUADSPI_DCR_CSHT_0) /*!<nCS stay high for at least 6 clock cycles between commands*/ +#define QSPI_CS_HIGH_TIME_7_CYCLE ((uint32_t)QUADSPI_DCR_CSHT_2 | QUADSPI_DCR_CSHT_1) /*!<nCS stay high for at least 7 clock cycles between commands*/ +#define QSPI_CS_HIGH_TIME_8_CYCLE ((uint32_t)QUADSPI_DCR_CSHT) /*!<nCS stay high for at least 8 clock cycles between commands*/ +/** + * @} + */ + +/** @defgroup QSPI_ClockMode QSPI Clock Mode + * @{ + */ +#define QSPI_CLOCK_MODE_0 ((uint32_t)0x00000000U) /*!<Clk stays low while nCS is released*/ +#define QSPI_CLOCK_MODE_3 ((uint32_t)QUADSPI_DCR_CKMODE) /*!<Clk goes high while nCS is released*/ +/** + * @} + */ + +/** @defgroup QSPI_Flash_Select QSPI Flash Select + * @{ + */ +#define QSPI_FLASH_ID_1 ((uint32_t)0x00000000U) +#define QSPI_FLASH_ID_2 ((uint32_t)QUADSPI_CR_FSEL) +/** + * @} + */ + + /** @defgroup QSPI_DualFlash_Mode QSPI Dual Flash Mode + * @{ + */ +#define QSPI_DUALFLASH_ENABLE ((uint32_t)QUADSPI_CR_DFM) +#define QSPI_DUALFLASH_DISABLE ((uint32_t)0x00000000U) +/** + * @} + */ + +/** @defgroup QSPI_AddressSize QSPI Address Size + * @{ + */ +#define QSPI_ADDRESS_8_BITS ((uint32_t)0x00000000U) /*!<8-bit address*/ +#define QSPI_ADDRESS_16_BITS ((uint32_t)QUADSPI_CCR_ADSIZE_0) /*!<16-bit address*/ +#define QSPI_ADDRESS_24_BITS ((uint32_t)QUADSPI_CCR_ADSIZE_1) /*!<24-bit address*/ +#define QSPI_ADDRESS_32_BITS ((uint32_t)QUADSPI_CCR_ADSIZE) /*!<32-bit address*/ +/** + * @} + */ + +/** @defgroup QSPI_AlternateBytesSize QSPI Alternate Bytes Size + * @{ + */ +#define QSPI_ALTERNATE_BYTES_8_BITS ((uint32_t)0x00000000U) /*!<8-bit alternate bytes*/ +#define QSPI_ALTERNATE_BYTES_16_BITS ((uint32_t)QUADSPI_CCR_ABSIZE_0) /*!<16-bit alternate bytes*/ +#define QSPI_ALTERNATE_BYTES_24_BITS ((uint32_t)QUADSPI_CCR_ABSIZE_1) /*!<24-bit alternate bytes*/ +#define QSPI_ALTERNATE_BYTES_32_BITS ((uint32_t)QUADSPI_CCR_ABSIZE) /*!<32-bit alternate bytes*/ +/** + * @} + */ + +/** @defgroup QSPI_InstructionMode QSPI Instruction Mode +* @{ +*/ +#define QSPI_INSTRUCTION_NONE ((uint32_t)0x00000000U) /*!<No instruction*/ +#define QSPI_INSTRUCTION_1_LINE ((uint32_t)QUADSPI_CCR_IMODE_0) /*!<Instruction on a single line*/ +#define QSPI_INSTRUCTION_2_LINES ((uint32_t)QUADSPI_CCR_IMODE_1) /*!<Instruction on two lines*/ +#define QSPI_INSTRUCTION_4_LINES ((uint32_t)QUADSPI_CCR_IMODE) /*!<Instruction on four lines*/ +/** + * @} + */ + +/** @defgroup QSPI_AddressMode QSPI Address Mode +* @{ +*/ +#define QSPI_ADDRESS_NONE ((uint32_t)0x00000000U) /*!<No address*/ +#define QSPI_ADDRESS_1_LINE ((uint32_t)QUADSPI_CCR_ADMODE_0) /*!<Address on a single line*/ +#define QSPI_ADDRESS_2_LINES ((uint32_t)QUADSPI_CCR_ADMODE_1) /*!<Address on two lines*/ +#define QSPI_ADDRESS_4_LINES ((uint32_t)QUADSPI_CCR_ADMODE) /*!<Address on four lines*/ +/** + * @} + */ + +/** @defgroup QSPI_AlternateBytesMode QSPI Alternate Bytes Mode +* @{ +*/ +#define QSPI_ALTERNATE_BYTES_NONE ((uint32_t)0x00000000U) /*!<No alternate bytes*/ +#define QSPI_ALTERNATE_BYTES_1_LINE ((uint32_t)QUADSPI_CCR_ABMODE_0) /*!<Alternate bytes on a single line*/ +#define QSPI_ALTERNATE_BYTES_2_LINES ((uint32_t)QUADSPI_CCR_ABMODE_1) /*!<Alternate bytes on two lines*/ +#define QSPI_ALTERNATE_BYTES_4_LINES ((uint32_t)QUADSPI_CCR_ABMODE) /*!<Alternate bytes on four lines*/ +/** + * @} + */ + +/** @defgroup QSPI_DataMode QSPI Data Mode + * @{ + */ +#define QSPI_DATA_NONE ((uint32_t)0X00000000) /*!<No data*/ +#define QSPI_DATA_1_LINE ((uint32_t)QUADSPI_CCR_DMODE_0) /*!<Data on a single line*/ +#define QSPI_DATA_2_LINES ((uint32_t)QUADSPI_CCR_DMODE_1) /*!<Data on two lines*/ +#define QSPI_DATA_4_LINES ((uint32_t)QUADSPI_CCR_DMODE) /*!<Data on four lines*/ +/** + * @} + */ + +/** @defgroup QSPI_DdrMode QSPI Ddr Mode + * @{ + */ +#define QSPI_DDR_MODE_DISABLE ((uint32_t)0x00000000U) /*!<Double data rate mode disabled*/ +#define QSPI_DDR_MODE_ENABLE ((uint32_t)QUADSPI_CCR_DDRM) /*!<Double data rate mode enabled*/ +/** + * @} + */ + +/** @defgroup QSPI_DdrHoldHalfCycle QSPI Ddr HoldHalfCycle + * @{ + */ +#define QSPI_DDR_HHC_ANALOG_DELAY ((uint32_t)0x00000000U) /*!<Delay the data output using analog delay in DDR mode*/ +#define QSPI_DDR_HHC_HALF_CLK_DELAY ((uint32_t)QUADSPI_CCR_DHHC) /*!<Delay the data output by 1/2 clock cycle in DDR mode*/ +/** + * @} + */ + +/** @defgroup QSPI_SIOOMode QSPI SIOO Mode + * @{ + */ +#define QSPI_SIOO_INST_EVERY_CMD ((uint32_t)0x00000000U) /*!<Send instruction on every transaction*/ +#define QSPI_SIOO_INST_ONLY_FIRST_CMD ((uint32_t)QUADSPI_CCR_SIOO) /*!<Send instruction only for the first command*/ +/** + * @} + */ + +/** @defgroup QSPI_MatchMode QSPI Match Mode + * @{ + */ +#define QSPI_MATCH_MODE_AND ((uint32_t)0x00000000U) /*!<AND match mode between unmasked bits*/ +#define QSPI_MATCH_MODE_OR ((uint32_t)QUADSPI_CR_PMM) /*!<OR match mode between unmasked bits*/ +/** + * @} + */ + +/** @defgroup QSPI_AutomaticStop QSPI Automatic Stop + * @{ + */ +#define QSPI_AUTOMATIC_STOP_DISABLE ((uint32_t)0x00000000U) /*!<AutoPolling stops only with abort or QSPI disabling*/ +#define QSPI_AUTOMATIC_STOP_ENABLE ((uint32_t)QUADSPI_CR_APMS) /*!<AutoPolling stops as soon as there is a match*/ +/** + * @} + */ + +/** @defgroup QSPI_TimeOutActivation QSPI TimeOut Activation + * @{ + */ +#define QSPI_TIMEOUT_COUNTER_DISABLE ((uint32_t)0x00000000U) /*!<Timeout counter disabled, nCS remains active*/ +#define QSPI_TIMEOUT_COUNTER_ENABLE ((uint32_t)QUADSPI_CR_TCEN) /*!<Timeout counter enabled, nCS released when timeout expires*/ +/** + * @} + */ + +/** @defgroup QSPI_Flags QSPI Flags + * @{ + */ +#define QSPI_FLAG_BUSY QUADSPI_SR_BUSY /*!<Busy flag: operation is ongoing*/ +#define QSPI_FLAG_TO QUADSPI_SR_TOF /*!<Timeout flag: timeout occurs in memory-mapped mode*/ +#define QSPI_FLAG_SM QUADSPI_SR_SMF /*!<Status match flag: received data matches in autopolling mode*/ +#define QSPI_FLAG_FT QUADSPI_SR_FTF /*!<Fifo threshold flag: Fifo threshold reached or data left after read from memory is complete*/ +#define QSPI_FLAG_TC QUADSPI_SR_TCF /*!<Transfer complete flag: programmed number of data have been transferred or the transfer has been aborted*/ +#define QSPI_FLAG_TE QUADSPI_SR_TEF /*!<Transfer error flag: invalid address is being accessed*/ +/** + * @} + */ + +/** @defgroup QSPI_Interrupts QSPI Interrupts + * @{ + */ +#define QSPI_IT_TO QUADSPI_CR_TOIE /*!<Interrupt on the timeout flag*/ +#define QSPI_IT_SM QUADSPI_CR_SMIE /*!<Interrupt on the status match flag*/ +#define QSPI_IT_FT QUADSPI_CR_FTIE /*!<Interrupt on the fifo threshold flag*/ +#define QSPI_IT_TC QUADSPI_CR_TCIE /*!<Interrupt on the transfer complete flag*/ +#define QSPI_IT_TE QUADSPI_CR_TEIE /*!<Interrupt on the transfer error flag*/ +/** + * @} + */ + +/** @defgroup QSPI_Timeout_definition QSPI Timeout definition + * @{ + */ +#define HAL_QPSI_TIMEOUT_DEFAULT_VALUE ((uint32_t)5000)/* 5 s */ +/** + * @} + */ + +/** + * @} + */ + +/* Exported macros -----------------------------------------------------------*/ +/** @defgroup QSPI_Exported_Macros QSPI Exported Macros + * @{ + */ + +/** @brief Reset QSPI handle state + * @param __HANDLE__: QSPI handle. + * @retval None + */ +#define __HAL_QSPI_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_QSPI_STATE_RESET) + +/** @brief Enable QSPI + * @param __HANDLE__: specifies the QSPI Handle. + * @retval None + */ +#define __HAL_QSPI_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN) + +/** @brief Disable QSPI + * @param __HANDLE__: specifies the QSPI Handle. + * @retval None + */ +#define __HAL_QSPI_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN) + +/** @brief Enables the specified QSPI interrupt. + * @param __HANDLE__: specifies the QSPI Handle. + * @param __INTERRUPT__: specifies the QSPI interrupt source to enable. + * This parameter can be one of the following values: + * @arg QSPI_IT_TO: QSPI Time out interrupt + * @arg QSPI_IT_SM: QSPI Status match interrupt + * @arg QSPI_IT_FT: QSPI FIFO threshold interrupt + * @arg QSPI_IT_TC: QSPI Transfer complete interrupt + * @arg QSPI_IT_TE: QSPI Transfer error interrupt + * @retval None + */ +#define __HAL_QSPI_ENABLE_IT(__HANDLE__, __INTERRUPT__) SET_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) + + +/** @brief Disables the specified QSPI interrupt. + * @param __HANDLE__: specifies the QSPI Handle. + * @param __INTERRUPT__: specifies the QSPI interrupt source to disable. + * This parameter can be one of the following values: + * @arg QSPI_IT_TO: QSPI Timeout interrupt + * @arg QSPI_IT_SM: QSPI Status match interrupt + * @arg QSPI_IT_FT: QSPI FIFO threshold interrupt + * @arg QSPI_IT_TC: QSPI Transfer complete interrupt + * @arg QSPI_IT_TE: QSPI Transfer error interrupt + * @retval None + */ +#define __HAL_QSPI_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) + +/** @brief Checks whether the specified QSPI interrupt source is enabled. + * @param __HANDLE__: specifies the QSPI Handle. + * @param __INTERRUPT__: specifies the QSPI interrupt source to check. + * This parameter can be one of the following values: + * @arg QSPI_IT_TO: QSPI Time out interrupt + * @arg QSPI_IT_SM: QSPI Status match interrupt + * @arg QSPI_IT_FT: QSPI FIFO threshold interrupt + * @arg QSPI_IT_TC: QSPI Transfer complete interrupt + * @arg QSPI_IT_TE: QSPI Transfer error interrupt + * @retval The new state of __INTERRUPT__ (TRUE or FALSE). + */ +#define __HAL_QSPI_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (READ_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) == (__INTERRUPT__)) + +/** + * @brief Get the selected QSPI's flag status. + * @param __HANDLE__: specifies the QSPI Handle. + * @param __FLAG__: specifies the QSPI flag to check. + * This parameter can be one of the following values: + * @arg QSPI_FLAG_BUSY: QSPI Busy flag + * @arg QSPI_FLAG_TO: QSPI Time out flag + * @arg QSPI_FLAG_SM: QSPI Status match flag + * @arg QSPI_FLAG_FT: QSPI FIFO threshold flag + * @arg QSPI_FLAG_TC: QSPI Transfer complete flag + * @arg QSPI_FLAG_TE: QSPI Transfer error flag + * @retval None + */ +#define __HAL_QSPI_GET_FLAG(__HANDLE__, __FLAG__) (READ_BIT((__HANDLE__)->Instance->SR, (__FLAG__)) != 0) + +/** @brief Clears the specified QSPI's flag status. + * @param __HANDLE__: specifies the QSPI Handle. + * @param __FLAG__: specifies the QSPI clear register flag that needs to be set + * This parameter can be one of the following values: + * @arg QSPI_FLAG_TO: QSPI Time out flag + * @arg QSPI_FLAG_SM: QSPI Status match flag + * @arg QSPI_FLAG_TC: QSPI Transfer complete flag + * @arg QSPI_FLAG_TE: QSPI Transfer error flag + * @retval None + */ +#define __HAL_QSPI_CLEAR_FLAG(__HANDLE__, __FLAG__) WRITE_REG((__HANDLE__)->Instance->FCR, (__FLAG__)) +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup QSPI_Exported_Functions + * @{ + */ + +/** @addtogroup QSPI_Exported_Functions_Group1 + * @{ + */ +/* Initialization/de-initialization functions ********************************/ +HAL_StatusTypeDef HAL_QSPI_Init (QSPI_HandleTypeDef *hqspi); +HAL_StatusTypeDef HAL_QSPI_DeInit (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_MspInit (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_MspDeInit(QSPI_HandleTypeDef *hqspi); +/** + * @} + */ + +/** @addtogroup QSPI_Exported_Functions_Group2 + * @{ + */ +/* IO operation functions *****************************************************/ +/* QSPI IRQ handler method */ +void HAL_QSPI_IRQHandler(QSPI_HandleTypeDef *hqspi); + +/* QSPI indirect mode */ +HAL_StatusTypeDef HAL_QSPI_Command (QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, uint32_t Timeout); +HAL_StatusTypeDef HAL_QSPI_Transmit (QSPI_HandleTypeDef *hqspi, uint8_t *pData, uint32_t Timeout); +HAL_StatusTypeDef HAL_QSPI_Receive (QSPI_HandleTypeDef *hqspi, uint8_t *pData, uint32_t Timeout); +HAL_StatusTypeDef HAL_QSPI_Command_IT (QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd); +HAL_StatusTypeDef HAL_QSPI_Transmit_IT (QSPI_HandleTypeDef *hqspi, uint8_t *pData); +HAL_StatusTypeDef HAL_QSPI_Receive_IT (QSPI_HandleTypeDef *hqspi, uint8_t *pData); +HAL_StatusTypeDef HAL_QSPI_Transmit_DMA (QSPI_HandleTypeDef *hqspi, uint8_t *pData); +HAL_StatusTypeDef HAL_QSPI_Receive_DMA (QSPI_HandleTypeDef *hqspi, uint8_t *pData); + +/* QSPI status flag polling mode */ +HAL_StatusTypeDef HAL_QSPI_AutoPolling (QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, QSPI_AutoPollingTypeDef *cfg, uint32_t Timeout); +HAL_StatusTypeDef HAL_QSPI_AutoPolling_IT(QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, QSPI_AutoPollingTypeDef *cfg); + +/* QSPI memory-mapped mode */ +HAL_StatusTypeDef HAL_QSPI_MemoryMapped(QSPI_HandleTypeDef *hqspi, QSPI_CommandTypeDef *cmd, QSPI_MemoryMappedTypeDef *cfg); +/** + * @} + */ + +/** @addtogroup QSPI_Exported_Functions_Group3 + * @{ + */ +/* Callback functions in non-blocking modes ***********************************/ +void HAL_QSPI_ErrorCallback (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_AbortCpltCallback (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_FifoThresholdCallback(QSPI_HandleTypeDef *hqspi); + +/* QSPI indirect mode */ +void HAL_QSPI_CmdCpltCallback (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_RxCpltCallback (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_TxCpltCallback (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_RxHalfCpltCallback (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_TxHalfCpltCallback (QSPI_HandleTypeDef *hqspi); + +/* QSPI status flag polling mode */ +void HAL_QSPI_StatusMatchCallback (QSPI_HandleTypeDef *hqspi); + +/* QSPI memory-mapped mode */ +void HAL_QSPI_TimeOutCallback (QSPI_HandleTypeDef *hqspi); +/** + * @} + */ + +/** @addtogroup QSPI_Exported_Functions_Group4 + * @{ + */ +/* Peripheral Control and State functions ************************************/ +HAL_QSPI_StateTypeDef HAL_QSPI_GetState (QSPI_HandleTypeDef *hqspi); +uint32_t HAL_QSPI_GetError (QSPI_HandleTypeDef *hqspi); +HAL_StatusTypeDef HAL_QSPI_Abort (QSPI_HandleTypeDef *hqspi); +HAL_StatusTypeDef HAL_QSPI_Abort_IT (QSPI_HandleTypeDef *hqspi); +void HAL_QSPI_SetTimeout (QSPI_HandleTypeDef *hqspi, uint32_t Timeout); +HAL_StatusTypeDef HAL_QSPI_SetFifoThreshold(QSPI_HandleTypeDef *hqspi, uint32_t Threshold); +uint32_t HAL_QSPI_GetFifoThreshold(QSPI_HandleTypeDef *hqspi); +/** + * @} + */ + +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup QSPI_Private_Macros QSPI Private Macros + * @{ + */ +/** @defgroup QSPI_ClockPrescaler QSPI Clock Prescaler + * @{ + */ +#define IS_QSPI_CLOCK_PRESCALER(PRESCALER) ((PRESCALER) <= 0xFF) +/** + * @} + */ + +/** @defgroup QSPI_FifoThreshold QSPI Fifo Threshold + * @{ + */ +#define IS_QSPI_FIFO_THRESHOLD(THR) (((THR) > 0) && ((THR) <= 32)) +/** + * @} + */ + +#define IS_QSPI_SSHIFT(SSHIFT) (((SSHIFT) == QSPI_SAMPLE_SHIFTING_NONE) || \ + ((SSHIFT) == QSPI_SAMPLE_SHIFTING_HALFCYCLE)) + +/** @defgroup QSPI_FlashSize QSPI Flash Size + * @{ + */ +#define IS_QSPI_FLASH_SIZE(FSIZE) (((FSIZE) <= 31)) +/** + * @} + */ + +#define IS_QSPI_CS_HIGH_TIME(CSHTIME) (((CSHTIME) == QSPI_CS_HIGH_TIME_1_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_2_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_3_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_4_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_5_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_6_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_7_CYCLE) || \ + ((CSHTIME) == QSPI_CS_HIGH_TIME_8_CYCLE)) + +#define IS_QSPI_CLOCK_MODE(CLKMODE) (((CLKMODE) == QSPI_CLOCK_MODE_0) || \ + ((CLKMODE) == QSPI_CLOCK_MODE_3)) + +#define IS_QSPI_FLASH_ID(FLA) (((FLA) == QSPI_FLASH_ID_1) || \ + ((FLA) == QSPI_FLASH_ID_2)) + +#define IS_QSPI_DUAL_FLASH_MODE(MODE) (((MODE) == QSPI_DUALFLASH_ENABLE) || \ + ((MODE) == QSPI_DUALFLASH_DISABLE)) + + +/** @defgroup QSPI_Instruction QSPI Instruction + * @{ + */ +#define IS_QSPI_INSTRUCTION(INSTRUCTION) ((INSTRUCTION) <= 0xFF) +/** + * @} + */ + +#define IS_QSPI_ADDRESS_SIZE(ADDR_SIZE) (((ADDR_SIZE) == QSPI_ADDRESS_8_BITS) || \ + ((ADDR_SIZE) == QSPI_ADDRESS_16_BITS) || \ + ((ADDR_SIZE) == QSPI_ADDRESS_24_BITS) || \ + ((ADDR_SIZE) == QSPI_ADDRESS_32_BITS)) + +#define IS_QSPI_ALTERNATE_BYTES_SIZE(SIZE) (((SIZE) == QSPI_ALTERNATE_BYTES_8_BITS) || \ + ((SIZE) == QSPI_ALTERNATE_BYTES_16_BITS) || \ + ((SIZE) == QSPI_ALTERNATE_BYTES_24_BITS) || \ + ((SIZE) == QSPI_ALTERNATE_BYTES_32_BITS)) + + +/** @defgroup QSPI_DummyCycles QSPI Dummy Cycles + * @{ + */ +#define IS_QSPI_DUMMY_CYCLES(DCY) ((DCY) <= 31) +/** + * @} + */ + +#define IS_QSPI_INSTRUCTION_MODE(MODE) (((MODE) == QSPI_INSTRUCTION_NONE) || \ + ((MODE) == QSPI_INSTRUCTION_1_LINE) || \ + ((MODE) == QSPI_INSTRUCTION_2_LINES) || \ + ((MODE) == QSPI_INSTRUCTION_4_LINES)) + +#define IS_QSPI_ADDRESS_MODE(MODE) (((MODE) == QSPI_ADDRESS_NONE) || \ + ((MODE) == QSPI_ADDRESS_1_LINE) || \ + ((MODE) == QSPI_ADDRESS_2_LINES) || \ + ((MODE) == QSPI_ADDRESS_4_LINES)) + +#define IS_QSPI_ALTERNATE_BYTES_MODE(MODE) (((MODE) == QSPI_ALTERNATE_BYTES_NONE) || \ + ((MODE) == QSPI_ALTERNATE_BYTES_1_LINE) || \ + ((MODE) == QSPI_ALTERNATE_BYTES_2_LINES) || \ + ((MODE) == QSPI_ALTERNATE_BYTES_4_LINES)) + +#define IS_QSPI_DATA_MODE(MODE) (((MODE) == QSPI_DATA_NONE) || \ + ((MODE) == QSPI_DATA_1_LINE) || \ + ((MODE) == QSPI_DATA_2_LINES) || \ + ((MODE) == QSPI_DATA_4_LINES)) + +#define IS_QSPI_DDR_MODE(DDR_MODE) (((DDR_MODE) == QSPI_DDR_MODE_DISABLE) || \ + ((DDR_MODE) == QSPI_DDR_MODE_ENABLE)) + +#define IS_QSPI_DDR_HHC(DDR_HHC) (((DDR_HHC) == QSPI_DDR_HHC_ANALOG_DELAY) || \ + ((DDR_HHC) == QSPI_DDR_HHC_HALF_CLK_DELAY)) + +#define IS_QSPI_SIOO_MODE(SIOO_MODE) (((SIOO_MODE) == QSPI_SIOO_INST_EVERY_CMD) || \ + ((SIOO_MODE) == QSPI_SIOO_INST_ONLY_FIRST_CMD)) + +/** @defgroup QSPI_Interval QSPI Interval + * @{ + */ +#define IS_QSPI_INTERVAL(INTERVAL) ((INTERVAL) <= QUADSPI_PIR_INTERVAL) +/** + * @} + */ + +/** @defgroup QSPI_StatusBytesSize QSPI Status Bytes Size + * @{ + */ +#define IS_QSPI_STATUS_BYTES_SIZE(SIZE) (((SIZE) >= 1) && ((SIZE) <= 4)) +/** + * @} + */ +#define IS_QSPI_MATCH_MODE(MODE) (((MODE) == QSPI_MATCH_MODE_AND) || \ + ((MODE) == QSPI_MATCH_MODE_OR)) + +#define IS_QSPI_AUTOMATIC_STOP(APMS) (((APMS) == QSPI_AUTOMATIC_STOP_DISABLE) || \ + ((APMS) == QSPI_AUTOMATIC_STOP_ENABLE)) + +#define IS_QSPI_TIMEOUT_ACTIVATION(TCEN) (((TCEN) == QSPI_TIMEOUT_COUNTER_DISABLE) || \ + ((TCEN) == QSPI_TIMEOUT_COUNTER_ENABLE)) + +/** @defgroup QSPI_TimeOutPeriod QSPI TimeOut Period + * @{ + */ +#define IS_QSPI_TIMEOUT_PERIOD(PERIOD) ((PERIOD) <= 0xFFFF) +/** + * @} + */ + +#define IS_QSPI_GET_FLAG(FLAG) (((FLAG) == QSPI_FLAG_BUSY) || \ + ((FLAG) == QSPI_FLAG_TO) || \ + ((FLAG) == QSPI_FLAG_SM) || \ + ((FLAG) == QSPI_FLAG_FT) || \ + ((FLAG) == QSPI_FLAG_TC) || \ + ((FLAG) == QSPI_FLAG_TE)) + +#define IS_QSPI_IT(IT) ((((IT) & (uint32_t)0xFFE0FFFFU) == 0x00000000U) && ((IT) != 0x00000000U)) +/** + * @} + */ + +/* Private functions ---------------------------------------------------------*/ +/** @defgroup QSPI_Private_Functions QSPI Private Functions + * @{ + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F7xx_HAL_QSPI_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/