Sadly I'm about to exchange the remote. The top left action button and volume up have crapped out. Common problem it seems.
On Dec 30, 2015 10:11 AM, "Scott Talbert" <s...@techie.net> wrote: > Can you recompile libconcord with debug enabled and provide the output? > (Add "CPPFLAGS=-D_DEBUG" to your ./configure) > > On Wed, 30 Dec 2015, Parker Reed wrote: > > Doesn't hit the reset cycle. Immediately dies after verifying. >> >> Manual reset worked. So might be an issue with the verification. >> >> On Wed, Dec 30, 2015 at 12:34 AM, Scott Talbert <s...@techie.net> wrote: >> Interesting. So it appears that the failure is happening when >> we are >> trying to reset the remote or reconnect to it after the reset. >> When using >> the USB 2.0 port, do you see the remote resetting (ie, the >> screen goes >> blank, starts booting up, etc)? >> >> Also, when using the USB 2.0 port, can you reset the remote >> successfully >> using 'concordance -r'? >> >> Scott >> >> On Tue, 29 Dec 2015, Parker Reed wrote: >> >> > Well that's interesting. Tried in a USB 3.0 port instead of >> 2.0 and it >> > worked! >> > >> > On Tue, Dec 29, 2015 at 11:37 PM, Parker Reed >> <parker.l.r...@gmail.com> >> > wrote: >> > Here's the info from the remote >> > >> > [parker@rcvrd ~]$ concordance -iv >> > Concordance 1.2 >> > Copyright 2007 Kevin Timmerman and Phil Dibowitz >> > This software is distributed under the GPLv3. >> > >> > Requesting identity: 100% done >> > Model: Logitech Harmony 880 (Espresso) >> > Skin: 15 >> > Firmware Version: 4.4 >> > Firmware Type: 0 >> > Hardware Version: 1.8.0 >> > External Flash: 2 MiB - 01:49 AMD Am29LV160BB >> > Architecture: 8 >> > Protocol: 8 >> > Manufacturer: Harmony Remote 0-4.4.2 >> > Product: Harmony Remote 0-4.4.2 >> > IRL, ORL, FRL: 0, 0, 0 >> > USB VID: 046D >> > USB PID: C110 >> > USB Ver: 080F >> > Serial Number: {EEEEEEEE-EEEE-EEEE-EEEE-EEEEEEEEEEEE} >> > {2819984D-F05A-4EE5-9FA9-C815851DFA4E} >> > {863D7E6E-17B4-4D95-A794-84207A436408} >> > Config Flash Used: 19% (372 of 1920 KiB) >> > >> > Success! >> > >> > >> > >> > On Tue, Dec 29, 2015 at 11:34 PM, Parker Reed >> > <parker.l.r...@gmail.com> wrote: >> > I registered on the old site, it gave me a >> > Connectivity.EZHex file, flashed it successfully, setup >> a >> > TV on the website, gave me another Connectivity.EZHex, >> > flashed successfully, but now when I try to flash the >> > Update.EZHex it gives me it errors out after verifying >> > every time. >> > >> > Remote is sitting in the dock and connected to computer. Tried >> > out of dock with same results. Libconcord and Concordance from >> > git. >> > >> > [parker@rcvrd ~]$ concordance -v Downloads/Update.EZHex >> > Concordance 1.2 >> > Copyright 2007 Kevin Timmerman and Phil Dibowitz >> > This software is distributed under the GPLv3. >> > >> > Requesting identity: 100% done >> > Contacting website: 100% done >> > Initializing update: 100% done >> > Invalidating flash: 100% done >> > Erasing flash: 100% done >> > Writing config: 100% 371 KiB done >> > Verifying config: 100% 371 KiB done >> > Failed to upload config: Unknown error >> > Failed with error -1 >> > >> > -Parker Reed >> > >> > >> > >> > >> > >> >> >> --------------------------------------------------------------------------- >> --- >> _______________________________________________ >> concordance-devel mailing list >> concordance-devel@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/concordance-devel >> >> >> >> > > ------------------------------------------------------------------------------ > > _______________________________________________ > concordance-devel mailing list > concordance-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/concordance-devel > >
------------------------------------------------------------------------------
_______________________________________________ concordance-devel mailing list concordance-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/concordance-devel