On Mon, Dec 14, 2015 at 03:42:09PM -0700, Joshua Henderson wrote:
> Document the devicetree bindings for PINCTRL and GPIO found on Microchip
> PIC32 class devices.
>
> Signed-off-by: Joshua Henderson <joshua.hender...@microchip.com>
> Cc: Ralf Baechle <r...@linux-mips.org>
Acked-by: Rob Herring <r...@kernel.org>
> ---
> .../bindings/gpio/microchip,pic32-gpio.txt | 49 ++++++++++++++++
> .../bindings/pinctrl/microchip,pic32-pinctrl.txt | 60
> ++++++++++++++++++++
> 2 files changed, 109 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt
> create mode 100644
> Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt
> b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt
> new file mode 100644
> index 0000000..ef37528
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt
> @@ -0,0 +1,49 @@
> +* Microchip PIC32 GPIO devices (PIO).
> +
> +Required properties:
> + - compatible: "microchip,pic32mzda-gpio"
> + - reg: Base address and length for the device.
> + - interrupts: The port interrupt shared by all pins.
> + - gpio-controller: Marks the port as GPIO controller.
> + - #gpio-cells: Two. The first cell is the pin number and
> + the second cell is used to specify the gpio polarity as defined in
> + defined in <dt-bindings/gpio/gpio.h>:
> + 0 = GPIO_ACTIVE_HIGH
> + 1 = GPIO_ACTIVE_LOW
> + 2 = GPIO_OPEN_DRAIN
> + - interrupt-controller: Marks the device node as an interrupt controller.
> + - #interrupt-cells: Two. The first cell is the GPIO number and second cell
> + is used to specify the trigger type as defined in
> + <dt-bindings/interrupt-controller/irq.h>:
> + IRQ_TYPE_EDGE_RISING
> + IRQ_TYPE_EDGE_FALLING
> + IRQ_TYPE_EDGE_BOTH
> + - clocks: Clock specifier (see clock bindings for details).
> + - microchip,gpio-bank: Specifies which bank a controller owns.
> + - gpio-ranges: Interaction with the PINCTRL subsystem.
> +
> +Example:
> +
> +/* PORTA */
> +gpio0: gpio0@1f860000 {
> + compatible = "microchip,pic32mzda-gpio";
> + reg = <0x1f860000 0x100>;
> + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + clocks = <&PBCLK4>;
> + microchip,gpio-bank = <0>;
> + gpio-ranges = <&pic32_pinctrl 0 0 16>;
> +};
> +
> +keys {
> + ...
> +
> + button@sw1 {
> + label = "ESC";
> + linux,code = <1>;
> + gpios = <&gpio0 12 0>;
> + };
> +};
> diff --git
> a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt
> b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt
> new file mode 100644
> index 0000000..4b5efa5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt
> @@ -0,0 +1,60 @@
> +* Microchip PIC32 Pin Controller
> +
> +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and
> +../interrupt-controller/interrupts.txt for generic information regarding
> +pin controller, GPIO, and interrupt bindings.
> +
> +PIC32 'pin configuration node' is a node of a group of pins which can be
> +used for a specific device or function. This node represents configuraions of
> +pins, optional function, and optional mux related configuration.
> +
> +Required properties for pin controller node:
> + - compatible: "microchip,pic32mada-pinctrl"
> + - reg: Address range of the pinctrl registers.
> + - clocks: Clock specifier (see clock bindings for details)
> +
> +Required properties for pin configuration sub-nodes:
> + - pins: List of pins to which the configuration applies.
> +
> +Optional properties for pin configuration sub-nodes:
> +----------------------------------------------------
> + - function: Mux function for the specified pins.
> + - bias-pull-up: Enable weak pull-up.
> + - bias-pull-down: Enable weak pull-down.
> + - input-enable: Set the pin as an input.
> + - output-low: Set the pin as an output level low.
> + - output-high: Set the pin as an output level high.
> + - microchip,digital: Enable digital I/O.
> + - microchip,analog: Enable analog I/O.
> +
> +Example:
> +
> +pic32_pinctrl: pinctrl@1f801400{
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "microchip,pic32mzda-pinctrl";
> + reg = <0x1f801400 0x400>;
> + clocks = <&PBCLK1>;
> +
> + pinctrl_uart2: pinctrl_uart2 {
> + uart2-tx {
> + pins = "G9";
> + function = "U2TX";
> + microchip,digital;
> + output-low;
> + };
> + uart2-rx {
> + pins = "B0";
> + function = "U2RX";
> + microchip,digital;
> + input-enable;
> + };
> + };
> +};
> +
> +uart2: serial@1f822200 {
> + compatible = "microchip,pic32mzda-uart";
> + reg = <0x1f822200 0x50>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> +};
> --
> 1.7.9.5
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
