Hi there, Just to clarify - I've forgotten to plug in the ethernet cable at one point and was panicking why there's a big red cross on atge0. So don't get too worked up about that part of the logs.
But otherwise it seems to have identical behaviour as before. I'm testing on snv_98. Regards, Alex. On Sat, Sep 20, 2008 at 7:35 PM, Alex Lam S.L. <[EMAIL PROTECTED]> wrote: > Hi there, > > No luck still - logs attached. Should I try a more "real" MAC address > to see if it makes a difference? > > Regards, > Alex. > > > > On Wed, Sep 17, 2008 at 7:05 PM, Masa Murayama <[EMAIL PROTECTED]> wrote: >> ----- Original Message ----- >>>Date: Wed, 17 Sep 2008 01:47:25 +0100 >>>From: "Alex Lam S.L." <[EMAIL PROTECTED]> >>>To: "Masa Murayama" <[EMAIL PROTECTED]> >>>Subject: Re: [driver-discuss] Atheros L1 GbE on P5E-VM HDMI >>>Cc: [email protected] >>> >>> >>>Hi there, >>> >>>Attached is the requested information, plus "scanpci" which I have >>>done for a defect report on OS tracker as well. >>> >>>Hope this helps, >>>Alex. >> >> Alex, >> >> Thank you very much for sending the logs. >> I think I found a problem. Current atge doesn't support to reading >> factory mac address from flash roms. But the L1 chipset in your board >> uses a flash rom for storing mac address. >> >>> Sep 16 18:33:50 opensolaris atge: [ID 198270 kern.info] atge0: atge_attach_ >> chip: called at time:43557 >>> Sep 16 18:33:50 opensolaris atge: [ID 688919 kern.info] atge0: atge_read_mac >> _addr: reading flash rom: not supported >>>Sep 16 18:33:50 opensolaris atge: [ID 451511 kern.info] atge0: MII PHY (0x004 >> dd015) found at 0 >> >> For a workaround, would you add following line into /kernel/drv/atge.conf >> then reboot your system. >> >> mac-addr="02:00:00:00:00:01"; >> >> -masa >>> >>> >>>On Tue, Sep 16, 2008 at 10:38 PM, Masa Murayama <[EMAIL PROTECTED]> wrote: >>>> ----- Original Message ----- >>>>>Date: Tue, 16 Sep 2008 00:15:23 +0100 >>>>>From: "Alex Lam S.L." <[EMAIL PROTECTED]> >>>>>To: [email protected] >>>>>Subject: [driver-discuss] Atheros L1 GbE on P5E-VM HDMI >>>>> >>>>> >>>>>Hi there, >>>>> >>>>>I have been browsing the web for this. I have tried the driver provided on: >>>>> >>>>>http://homepage2.nifty.com/mrym3/taiyodo/eng/ >>>>> >>>>>But even though the device seems to set up properly and I can see it >>>>>properly in Device Utility and even some packets sent / received, it >>>>>does not work under any DHCP / static IP setup, whether using NWAM or >>>>>not. >>>>> >>>>>(Nonetheless, very kind of you. Thank you!) >>>>> >>>>>Any pointers as to what I can do next? >>>> >>>> Thank you very much for testing atge drver. Would you show following to me? >>>> >>>> (1) message lines from atge driver in /var/adm/messages >>>> >>>> (2) output of ifconfig -a. I prefer statis IP rather than DHCP. >>>> >>>> (3)output of "kstat atge" and "netstat -s" after you tested ping >>>> or telnet to other network node in the same ethernet segment. >>>> >>>> -masa >>>> >>>> >>>>>Regards, >>>>>Alex. >>>>>_______________________________________________ >>>>>driver-discuss mailing list >>>>>[email protected] >>>>>http://mail.opensolaris.org/mailman/listinfo/driver-discuss >>>> >>>> >> >> > _______________________________________________ driver-discuss mailing list [email protected] http://mail.opensolaris.org/mailman/listinfo/driver-discuss
