The default box will use the baud rate and hex address used in the rig file. Unclicking allows you to override the settings.
DTR doesn't have to be on unless your interface requires it for power. Make sure the baud rate on the PROIII is not "Auto" but set to a baud rate, auto can sometimes be problematical... it was designed for use with other Icom peripherals. CI-V transceive should be off for D4W. None of the above really explains the symptoms. It sounds as if the PROIII is not recieving the polling instruction. What is the Poll rate set to in D4W? On 2011-02-04 19:55, N0KK,Kirk wrote: > My preferences under the radio tab are as follows. (It is what they have > been for years) > > Type: ICOM 756 PRO III > Address: 6E > Baud: 9600 > Both the "default" boxes are checked. Though this has no effect on operation > Com port settings are correct. Radio 1 is com 3, radio 2 is com 7. > Poll rate is currently at 5000ms. I usually keep it at 1000ms though. > Max tries is 5 > DTR is set to high. > Transverter offset is 0 Band none > > Other than the COM settings, I have both radios set the same for ease of > operation between programs and has worked flawlessly for several years. > > Kirk > > On 2/4/2011 6:40 PM, n...@aol.com wrote: >> >> Kirk, >> >> Check your radio settings in Preferences. For whatever reason, importing >> a previously saved ini file does NOT set these settings. They're all >> "default" - even after an import. >> >> Steve >> >> In a message dated 2/4/2011 6:29:01 P.M. Central Standard Time, >> n...@usfamily.net writes: >> >> I upgrade to 8.04 I also switched PC's. >> >> Pulled all ini files etc to new PC all is working well...rotor controls, >> internet etc. Where I'm running into conflict is in the radio control. >> >> Let me preface this by saying the rig control is working as it should in >> all other programs I use. Writelog, MMTTY..etc >> >> What is happening is this...WHILE I tune the radios frequency knob...The >> cursor blinks and freq reads as it should. If I STOP tuning..cursor >> stops blinking and radio times out. >> >> I made NO changes to the rig settings and as a stated I used the ini >> file from my other pc. >> >> Anyone with some thoughts? >> >> Kirk >> >> >> ______________________________________________________________ >> Dx4win mailing list >> Home: http://mailman.qth.net/mailman/listinfo/dx4win >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Dx4win@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> >> >> >> ______________________________________________________________ >> Dx4win mailing list >> Home: http://mailman.qth.net/mailman/listinfo/dx4win >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Dx4win@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> >> > ______________________________________________________________ > Dx4win mailing list > Home: http://mailman.qth.net/mailman/listinfo/dx4win > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Dx4win@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Dx4win mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Dx4win@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
