I had a similar problem -- even at low power levels, the W2 would
periodically spike a high-SWR and even show 2-3 bars of SWR when no signal
was present. I swapped out the 8-pin cable connecting the sensor to the
W2 and the problem went away. I re-crimped the connectors on the original
cable, but haven't yet swapped it back in to see if doing so fixed the
problem.
On Wed, 12 Aug 2015, Randy Farmer wrote:
I find this thread quite interesting. I too have been dealing with VSWR
"spurts". My TX lineup is similar to Phil's, but I don't have the TX
Monitor. After a recent station rewiring job I found I was having a
great deal of trouble with indicated VSWR jumping to high levels with
the amplifier on. The problem was especially bad on 80 meters --
anything above about 300W would randomly give a high VSWR fault on the
KAT500. Since the KPA500 was feeding the suddenly changed load it too
would usually fault out. The sensor for my LP-100A is on the antenna
side of the KAT500, and its VSWR indication was rock solid during these
events. My station is in an extremely difficult RFI environment, with
seven antennas crammed onto a 0.2 acre city lot. I immediately suspected
that common mode RF was getting into the reverse power sensor circuit in
the KAT500.
I installed a Balun Designs choke on the antenna side of the LP-100A
sensor and the KAT500 stopped giving the high VSWR indications right
away. That's the good news. The bad news is that now the KPA500 is doing
it, but at considerably higher power levels. I can run around 400W out
before the KPA500 begins to randomly show VSWR faults. The KAT500 is
completely stable at full power. For now, I'm living with this situation.
So I would suggest the troubles you're seeing may be the result of
common mode RF problems on the transmitter feedline. It could be that
the addition of the extra electrical length of the TX Monitor sensor and
its associated cabling changed things just enough to put a common mode
voltage node near the KAT500 output port. You might try adding an
additional piece of coax somewhere in the lineup and see if that changes
the situation. RF is funny stuff.
73...
Randy, W8FN
On 8/12/2015 10:10 AM, Phil Hystad wrote:
Mike,
Thanks for the comment. I only have one K3 with one P3. My configuration
is:
K3/P3 —> KPA500 —> TX Mon Sensor —> LP100A Sensor —> KAT500 —>
80-meter Dipole
I first noticed the spike with the RED LEDs on both the KAT500 and the
KPA500. I was not looking
at the SWR display on the P3 although the second time I did notice that it
too spiked (max reading).
Like I said, I was operating CW and when I sent just the first dit of a QNI
into a CW net the spike occurred.
I stopped, and then keyed again and everything was normal. The second time
that I did this, I thought that
maybe the spike was momentary and continued keying but the second or third
key down action (actually, a paddle)
resulted in fault with the KPA500.
Last night, I did not have any problems at all because I disconnected the
TX Mon sensor. I will continue
experimenting though as I don’t have too many data points yet to draw
conclusions.
73, phil, K7PEH
On Aug 12, 2015, at 7:28 AM, Mike VE3YF <m...@ve3yf.com> wrote:
Phil:
I have the same setup but only 1 x P3. A K3 and P3 on my left setup and a
K3 on the right setup using a MK2R+ and I noticed what you mention only once.
I was on 80m with
the Right K3 and I saw a brief Power and SWR spike on the Left P3 and K3.
I might have had a bit of SWR on the standalone Right K3. I have not noticed
it happen since, it might
be a band/swr specific issue ie, as I was operating around 3800 and the
antenna is designed for the CW and RTTY portion of the band. The Left side
radio was on 160m Sloper
73 De Mike
VE3YF
http://www.ve3yf.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to joberreu-elecr...@moselle.com
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
