Hi, Yes, the ";" is a slight delay... However I believe this issue goes beyond a simple delay...
As I mentioned in my last post, I have a set of macros, where the last macro crashes the first macro in the string... In my mind, that pretty well eliminates all timing issues... -- 73's, and thanks, Dave For software/hardware reviews see: http://www.nk7z.net For MixW support see: https://groups.yahoo.com/neo/groups/mixw/info For SSTV help see: http://groups.yahoo.com/neo/groups/MM-SSTV/info On Wed, 2016-02-17 at 15:22 -0600, Clay Autery wrote: > I haven't looked into the command language for the P3 in depth yet... > > Is there a command for a "time delay". It would appear that you need > to > insert a time delay in between each individual command to allow the > unit > time to respond to each step. > > Just a SWAG... (If the command doesn't exist, it looks like a prime > candidate for the next Firmware iteration) > > ______________________ > Clay Autery, KG5LKV > (318) 518-1389 > > On 2/17/2016 2:46 PM, Dave Cole wrote: > > Hello Tim and Gary, > > > > I have done extensive testing in trying to get a macro to perform > > this > > exact behavior... > > > > I do not believe "currently" there is a way to make this happen via > > macro commands. > > > > If you perform the needed steps by hand, with lots of space between > > commands, it works, if you then place the exact same commands in a > > macro it fails. > > > > I tested by placing each command below in its own macro key using > > the > > P3 Macro tester software included with the P3 utility. Here is an > > example: > > > > I have a DX station at 14.010, and I want to move 14.010 to the > > left > > edge of the P3, showing the upper 5 KHz ra > > > > > > Macro 1: > > #SPN000100; > > Sets span to plus and minus 10 KHz. > > > > Macro 2: > > UP7; > > Moves K3 up 5 KHz. > > > > Macro 3: > > #FXT1; > > Places the P3 in sticky mode, (Fixed Tune), locking the transmit > > frequency to the center of the P3 screen. > > > > Macro 4: > > DN7; > > Moves the K3 down 5, dragging the transmit freq down with it, and > > putting the transmit freq on the left edge of the P3, exposing the > > upper 10 KHz of the signals on the P3. > > > > If I then fire them one at a time, everything works as expected, > > the > > transmit frequency is on the lower left edge for an up split. > > > > If I place them in a single macro, it fails, every time... > > > > > > 73's, and thanks, > > Dave > > > > For software/hardware reviews see: > > http://www.nk7z.net > > > > For MixW support see: > > https://groups.yahoo.com/neo/groups/mixw/info > > > > For SSTV help see: > > http://groups.yahoo.com/neo/groups/MM-SSTV/info > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to d...@nk7z.net ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com