Bill - hunh. I didn’t think of testing it that way, but clearly that works and tells the tale. Kind of off-putting, knowing that you’re really up to 99 Hz away from where you think you are when you select Coarse. Maybe a good use for a macro.
73, Bob W3Dk From: Bill Weaver [mailto:weave...@usermail.com] Sent: Thursday, October 17, 2019 9:31 AM To: Bob Novas; Bob Novas via Elecraft Subject: Re: [Elecraft] Question on frequency when in fine/medium/coarse The undisplayed digits are used, i.e. the freq does not shift to the displayed 100Hz. In my example the freq (while listening to a CW QSO) did not shift but stayed at 7.02647 Khz. 73, Bill WE5P On Oct 17, 2019 at 08:59, Bob Novas <bob.no...@verizon.net> wrote: But, the question is - are the undisplayed digits retained but not used, or are they actually utilized in determining the frequency? I’ve been setting my readout to xxxx.x00 before switching to Coarse, on the fea that the undisplayed digits actually are used in determining the Rx/Tx frequency, but there’s nowhere that says one way or the other that I can find. Bob - W3DK From: Bill Weaver [mailto:weave...@usermail.com] Sent: Thursday, October 17, 2019 8:34 AM To: Bill Weaver; Bob Novas; Bob Novas via Elecraft Subject: Re: [Elecraft] Question on frequency when in fine/medium/coarse Sri, when selecting coarse to 7.0264 not 7.02644. Fat fingers 73, Bill WE5P On Oct 17, 2019 at 08:31, Bill Weaver <weave...@usermail.com> wrote: Bob, I just tested it It looks like the undisplayed digits are retained. My example 7.02647. Select coarse 7.02644 tune around and return to 7.0264 and select medium returns to 7.02647. 73, Bill WE5P > > On Oct 17, 2019 at 08:23, Bob Novas via Elecraft wrote: > > > When the K3s is in Coarse tuning mode, showing 100 Hz steps, are the 10 Hz > and 1 Hz settings retained from wherever they were, or are they jammed to > 0's? In other words, if the dial reads 7010.1, is the K3s running on the > frequency 7010.100 or possibly 7010.1?? where the ?? are whatever happened to > be dialed in before going to Coarse tuning? Thanks, Bob Novas - W3DK > ______________________________________________________________ Elecraft > mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: > http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This > list hosted by: http://www.qsl.net Please help support this email list: > http://www.qsl.net/donate.html Message delivered to weaverwf@usermailcom > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to weave...@usermail.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com