Paul, If you got a null reading of 006, there is no sense in re-doing it - that is sufficiently low. Do the procedures below in the order listed. Stop when one does not produce the expected result. Each step depends on the one prior to it.
Put the KAT2 in CALn, CAL P or CAL S and then remove the coax from the K2 RF Board (but connect a 50 ohm dummy load to ANT1. Measure the resistance between the KAT2 input coax and ground - it should read 50 ohms (just like your dummy load). If that is not the case, you likely have a soldering problem at one of the relays. Ignoring the potential relay problem for a bit, it would be a good idea to verify the wattmeter. Set the KAT2 to ANT1 and then power off and separate the KAT2 Control Board from the LC board and set the LC board aside. Make a jumper wire that extends from J4 pin 2 to J5 pin 15 (this is a long jumper that plugs into the 2nd pin from the extreme ends of J4 and J5). That bypasses the L/C section of the KAT2 completely. Measure the resistance between the center conductor of the input coax and the center conductor of the ANT1 jack - it should be very low resistance. If that is true, then go on to the next step - otherwise stop and let me know what you find. Now, connect a dummy load to the ANT1 jack. As a sanity check, measure the resistance from the center conductor of the input coax and the shield - it should be 50 ohms, if it is not, find the problem before proceeding. If you measured 50 ohms in the step above, connect the input coax to the RF Board and try a TUNE with the Power knob set to greater than 2 watts. You should have about 2 watts output. Next set the menu ATU parameter to CAL P and connect a wattmeter that you trust at the 2 watt level between the ANT1 jack and the dummy load, and do a TUNE. Adjust R1 (FWD) to make the K2 display match your external wattmeter. If the above procedure is successful, remove the jumper and mate the L/C board to the control board and repeat the procedure. The results should be almost the same, but you may have to tweak the R1 pot a bit because there is some residual impedance in the L/C section of the KAT2. If you got this far, you are almost done (and all is OK). Set the REFL pot to the same physical position as the FWD pot and put everything back in order - you are done. Let us know where the steps above fail. What works as well as where it fails is important. 73, Don W3FPR Paul Locker wrote: > Don et all, > I've had a dummy load connected and still get a high current message. With > the > same dummy load, the ATU struggles to find a match for ant1, however for ant2 > it > finds a match with out issues. For my null, I got 006. > > > This evening I'm going to go back and redo the CALn setting. > > > Thank you for your time on the list. > > > Paul > > > "Don't forget to take the right Path" > > -JRDL > > > > > ________________________________ > From: Don Wilhelm <w3...@embarqmail.com> > To: Paul Locker <pmlo...@yahoo.com> > Cc: Elecraft@mailman.qth.net > Sent: Fri, July 16, 2010 8:01:57 PM > Subject: Re: [Elecraft] K2 KAT2 Issues/Questions > > Paul, > > Not quite enough information yet to give you a positive answer. > Are you using the KAT2 in the ATU CAL menu setting? If not, what do you have > connected to the ANT jack(s) - hopefully a dummy load. If it is other than a > dummy load, what happens with a dummy load attached? > Did you obtain a good null when you balanced the KAT2 wattmeter? If not, > that > is the starting point, even if that is not the problem source. > > 73, > Don W3FPR > > Paul Locker wrote: > >> I have just finished the installation of my kat2 I got at Dayton. I am >> seeing >> a high current warning for any band I use above 2 watts. I tried the other >> antenna position and noticed it resulted in a different swr. I changed my >> ground and that didn't improve the high current warning as I read in the >> manual >> that it could be an issue. >> >> >> Is there anything specific I need to check or do to start my troubleshooting? >> >> Paul >> k4pml >> >> >> "Don't forget to take the right Path" >> >> -JRDL >> >> >> >> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> >> >> > > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
