Frank, For some reason this is getting ignored... check your MDI window after you load and you will see G64 not G61.1 as the active G codes.
John On 11 Nov 2009 at 7:23, Frank Tkalcevic wrote: > If I only have G61.1 in the ini file, the sim shows a significantly > curved > path. Putting G61.1 in the gcode file will trace the path as > expected. > > I only tried it in a sim version. I wasn't game to run it on the > real > machine while it was drawing curved paths. The particular path I > noticed it > on was retracting the parting tool from a deep groove. Watching it > go > sideways through the part was a bit upsetting. > > Frank > > > -----Original Message----- > > From: John Thornton [mailto:bjt...@gmail.com] > > Sent: Tuesday, 10 November 2009 11:13 PM > > To: Enhanced Machine Controller EEMC" > > Subject: Re: [Emc-users] G61/G61.1 not working when put in > > ini file startupfield > > > > The traced route might not be exactly the cut route because > > of delays in updating the screen. The display is not updated > > in real time AFAIK. I have noticed that when doing very small > > work with G61 or G61.1 which are the same. > > > > John > > > > On 10 Nov 2009 at 9:10, Frank Tkalcevic wrote: > > > > > In my lathe configuration, I have... > > > > > > RS274NGC_STARTUP_CODE = G18 G7 G61.1 > > > > > > in the [RS274NGC] section of the ini file. > > > > > > Even though on the MDI panel G61.1 is shown to be an active > G-Code, > > > the route traced is cutting corners. I need to explicitly > > put G61.1 > > > in my Gcode program for it to work. > > > > > > Is this a bug, or my misunderstanding of how this works? > > > > > > Thanks, > > > Frank > > > > > > > > > > -------------------------------------------------------------------- > > > ---------- > > > Let Crystal Reports handle the reporting - Free Crystal > > Reports 2008 > > > 30-Day trial. Simplify your report design, integration and > > deployment > > > - and focus on what you do best, core application coding. > Discover > > > what's new with Crystal Reports now. > http://p.sf.net/sfu/bobj-july > > > _______________________________________________ > > > Emc-users mailing list > > > Emc-users@lists.sourceforge.net > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > -------------------------------------------------------------- > > ---------------- > > Let Crystal Reports handle the reporting - Free Crystal > > Reports 2008 30-Day trial. Simplify your report design, > > integration and deployment - and focus on what you do best, > > core application coding. Discover what's new with Crystal > > Reports now. http://p.sf.net/sfu/bobj-july > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > -------------------------------------------------------------------- > ---------- > Let Crystal Reports handle the reporting - Free Crystal Reports 2008 > 30-Day > trial. Simplify your report design, integration and deployment - and > focus on > what you do best, core application coding. Discover what's new > with > Crystal Reports now. http://p.sf.net/sfu/bobj-july > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day trial. Simplify your report design, integration and deployment - and focus on what you do best, core application coding. Discover what's new with Crystal Reports now. http://p.sf.net/sfu/bobj-july _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users