Don,
Are you sure the card is actually at the 0x00 address? lspci -v
should tell you the correct address, I think. Folks that use this card
may be able to help you out a bit more, if the lspci command is not
correct. Something at that address is not loading.
Mark
On 10/06/2010 09:09 AM, Don Stanley wrote:
> Thanks Mark;
> The jetmill1_load.hal file is below.
> This is the univstep_load.hal file from Pico-Systems, less some comments.
> loadrt hal_ppmc extradac=0x00 (appears to be EMC 10.04's complaint)
> Don
>
> On Wed, Oct 6, 2010 at 5:32 AM, Mark Wendt <[email protected]
> <mailto:[email protected]>> wrote:
>
> Don,
>
> Replies embedded below.
>
> On 10/06/2010 12:14 AM, Don Stanley wrote:
> > Hi All;
> > The EMC Errors File is probably telling me what is
> > wrong but I'm on too many shifts today to figure it out.
> >
> > EMC Errors:
> >
> >
> <snippage>
> > Debug file information:
> > insmod: error inserting
> > '/usr/realtime-2.6.32-122-rtai/modules/emc2/hal_ppmc.ko': -1
> Operation not
> > permitted
> > jetmill1_load.hal:8: exit value: 1
> > jetmill1_load.hal:8: insmod failed, returned -1
> >
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
>
> Here's the goodies. Something on line 8 in your jetmill_load.hal file
> is causing problems. Can you post that file?
> > See the output of 'dmesg' for more information.
> > 1382
> > PID TTY STAT TIME COMMAND
> > Stopping realtime threads
> > Unloading hal components
> >
> >
> > I have tried CMOS printer settings EPP and ECP with no change.
> > What is mode 4?
> > Which is the prefered setting EPP or ECP, when it is working?
> >
> EPP is the setting you're looking for.
> > Help and Thanks
> > Don
> Mark
>
> ______________________________________________
> # sample file pulls all load commands into a single file
> # when emc2 starts it loads iocontrol
>
> # load realtime modules
> loadrt trivkins
> loadrt [EMCMOT]EMCMOT base_period_nsec=[EMCMOT]BASE_PERIOD
> servo_period_nsec=[EMCMOT]SERVO_PERIOD
> traj_period_nsec=[EMCMOT]TRAJ_PERIOD key=[EMCMOT]SHMEM_KEY
> loadrt pid num_chan=4
> loadrt hal_ppmc extradac=0x00
> loadrt abs count=1
> loadrt mux2 count=1
> loadrt scale count=1
>
> # load scope and make some signals for the scope for tuning.
> loadrt scope_rt
> loadrt ddt count=4
> loadrt estop_latch count=1
> loadrt and2 count=5
> loadrt or2 count=2
>
> # Add functions to servo thread.
> # inputs get read at the beginning of the thread
> addf ppmc.0.read servo-thread
> # then run the motion controller
> addf motion-command-handler servo-thread
> addf abs.0 servo-thread
> addf mux2.0 servo-thread
> addf scale.0 servo-thread
> addf and2.0 servo-thread
> addf and2.1 servo-thread
> addf and2.2 servo-thread
> addf and2.3 servo-thread
> addf and2.4 servo-thread
> addf or2.0 servo-thread
> addf or2.1 servo-thread
> addf estop-latch.0 servo-thread
> addf motion-controller servo-thread
> # then the PID loops
> addf pid.0.do-pid-calcs servo-thread
> addf pid.1.do-pid-calcs servo-thread
> addf pid.2.do-pid-calcs servo-thread
> addf pid.3.do-pid-calcs servo-thread
> # write outputs last
> addf ppmc.0.write servo-thread
>
>
>
> ------------------------------------------------------------------------------
> Beautiful is writing same markup. Internet Explorer 9 supports
> standards for HTML5, CSS3, SVG 1.1, ECMAScript5, and DOM L2 & L3.
> Spend less time writing and rewriting code and more time creating
> great
> experiences on the web. Be a part of the beta today.
> http://p.sf.net/sfu/beautyoftheweb
> _______________________________________________
> Emc-users mailing list
> [email protected]
> <mailto:[email protected]>
> https://lists.sourceforge.net/lists/listinfo/emc-users
>
>
------------------------------------------------------------------------------
Beautiful is writing same markup. Internet Explorer 9 supports
standards for HTML5, CSS3, SVG 1.1, ECMAScript5, and DOM L2 & L3.
Spend less time writing and rewriting code and more time creating great
experiences on the web. Be a part of the beta today.
http://p.sf.net/sfu/beautyoftheweb
_______________________________________________
Emc-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/emc-users
