Am 11.07.2013 um 05:40 schrieb Troy Jacobson <t...@thismuch.net>: > The machinekit image does not flash the LEDs to show activity. Numbers 3 > and 5 are on constantly for that image. That's a mistake I made...
sorry, I should have noted that In the current (-bone20) xenomai kernel the led_gpio driver is compiled as a module, as opposed to compiled in by default the reason is to prevent the kernel on trampling on Ian's hal_bb_gpio driver which can drive leds too - Michael > > > > > On Wed, Jul 10, 2013 at 1:03 AM, Klemen Dovrtel > <klemen_dovr...@yahoo.com>wrote: > >> Thank for the info. I made the SD image as described. Then i tried to >> flash the board. I switched the power off, plugged in the sd card and >> switched the power on while holding the boot button. All four user leds lit >> for a second or so and than the led 3 and 5 lit solid. I thought now i have >> to wait for 45 minutes, but nothing happened. Later i tried the board but >> it still runs with the default software. Any idea what could be wrong? >> >> A also tried to start the board with the sd card inserted and i noticed >> that the sd card was rewritten with some default beagle board documentation. >> >> Regards >> Klemen >> >> >> >> >> ________________________________ >> From: Charles Steinkuehler <char...@steinkuehler.net> >> To: Klemen Dovrtel <klemen_dovr...@yahoo.com>; Enhanced Machine >> Controller (EMC) <emc-users@lists.sourceforge.net> >> Sent: Tuesday, July 9, 2013 12:40 PM >> Subject: Re: [Emc-users] Beaglebone LinuxCNC starterkit -> Beaglebone Black >> >> >> On 7/9/2013 3:40 AM, Klemen Dovrtel wrote: >>> Hello everybody, >>> >>> I noticed the BeagleBone version of LinuxCNC and decided to try it, but >> it seems i was not paying enough attention - I bought the Beaglebone Black >> instead of Beaglebone. >>> >>> Is there a simple way to make the Beaglebone LinuxCNC starterkit work on >> BeagleBone Black? Can i use the BeagleBone ready to run sd to flash the >> BeagleBone Black? >> >> That image is dated. You should start with the SD image from here: >> >> http://bb-lcnc.blogspot.com/p/machinekit_16.html >> >> ...it works fine with the "White" or the Black. >> >> -- >> Charles Steinkuehler >> char...@steinkuehler.net >> >> ------------------------------------------------------------------------------ >> See everything from the browser to the database with AppDynamics >> Get end-to-end visibility with application monitoring from AppDynamics >> Isolate bottlenecks and diagnose root cause in seconds. >> Start your free trial of AppDynamics Pro today! >> http://pubads.g.doubleclick.net/gampad/clk?id=48808831&iu=/4140/ostg.clktrk >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> > ------------------------------------------------------------------------------ > See everything from the browser to the database with AppDynamics > Get end-to-end visibility with application monitoring from AppDynamics > Isolate bottlenecks and diagnose root cause in seconds. > Start your free trial of AppDynamics Pro today! > http://pubads.g.doubleclick.net/gampad/clk?id=48808831&iu=/4140/ostg.clktrk > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ See everything from the browser to the database with AppDynamics Get end-to-end visibility with application monitoring from AppDynamics Isolate bottlenecks and diagnose root cause in seconds. Start your free trial of AppDynamics Pro today! http://pubads.g.doubleclick.net/gampad/clk?id=48808831&iu=/4140/ostg.clktrk _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users