Both show good in the Tek 'scope with the probes clipped onto the little bit of wire accessible from the screw terminals on the 7i76. Hard to imagine the wire clamped in the screw terminal but not making contact. With LinuxCNC running doesn't it reset that count with each read so it only will show the counts since the last read?
------Original Mail------ From: "Peter C. Wallace" <p...@mesanet.com> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> Sent: Wed, 29 Oct 2014 12:39:08 -0700 PDT Subject: Re: [Emc-users] Lathe conversion with Mesa 5i25 / 7i76 On Wed, 29 Oct 2014, p...@wpnet.us wrote: > Date: Wed, 29 Oct 2014 14:04:00 -0500 > From: p...@wpnet.us > Reply-To: "Enhanced Machine Controller (EMC)" > <emc-users@lists.sourceforge.net> > To: emc-users@lists.sourceforge.net > Subject: Re: [Emc-users] Lathe conversion with Mesa 5i25 / 7i76 > > Ok, I verified the pin and changed the line in the HAL to: > > net mpg_count hm2_5i25.0.7i76.0.0.enc0.count => axis.0.jog-counts > axis.2.jog-counts axis.1.jog-counts > > With halcmd I can show hm2_5i25.0.7i76.0.0.enc0.count and see it go to 1 > briefly when spinning the MPG, so it looks like the signal is getting in ok > but I'm still not getting any axis movement. > if it does not count beyond 0,1 that indicates that either A or B is not being seen (either a wiring or level issue) > > > ------Original Mail------ > From: "Peter C. Wallace" <p...@mesanet.com> > To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> > Sent: Wed, 29 Oct 2014 11:13:06 -0700 PDT > Subject: Re: [Emc-users] Lathe conversion with Mesa 5i25 / 7i76 > > On Wed, 29 Oct 2014, p...@wpnet.us wrote: > >> Date: Wed, 29 Oct 2014 12:57:50 -0500 >> From: p...@wpnet.us >> Reply-To: "Enhanced Machine Controller (EMC)" >> <emc-users@lists.sourceforge.net> >> To: emc-users@lists.sourceforge.net >> Subject: Re: [Emc-users] Lathe conversion with Mesa 5i25 / 7i76 >> >> hm2_5i25.0.encoder.00. is the hardware high speed encoder? >> hm2_5i25.0.encoder.01. is not the low speed encoder? > > hm2_5i25.0.encoder.01 is the spindle encoder for the second 7I76 (assuming you > are using a 7i76x2 config) > > hm2_5i25.0.7i76.0.0.enc0 > > is the first MPG encoder (it may have a different name in master) > best thing for checking is to list all the pins with > > halcmd show pins > pinlist.txt > > when linuxcnc is running > >> >> I've been looking through all the HostMot2 docs I can find including the >> section on encoders and it's not very clear to me. >> >> http://www.linuxcnc.org/docs/2.6/html/drivers/hostmot2.html#_encoder >> >> The PNCConf seems to think hm2_5i25.0.encoder.00. is the high speed spindle >> encoder input, so i presumed that when set to mode2 the low speed encoder >> inputs GPIO 16..19 would occupy the next two encoder instances. >> >> The only reference to the low speed encoder inputs I've found is the >> sentence or two on pg.18 of the 7i76man.pdf you pointed out. Surely there is >> a more detailed explanation of this somewhere? >> >> >> >> ------Original Mail------ >> From: "Peter C. Wallace" <p...@mesanet.com> >> To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> >> Sent: Wed, 29 Oct 2014 10:43:46 -0700 PDT >> Subject: Re: [Emc-users] Lathe conversion with Mesa 5i25 / 7i76 >> >> On Wed, 29 Oct 2014, p...@wpnet.us wrote: >> >>> Date: Wed, 29 Oct 2014 12:29:53 -0500 >>> From: p...@wpnet.us >>> Reply-To: "Enhanced Machine Controller (EMC)" >>> <emc-users@lists.sourceforge.net> >>> To: emc-users@lists.sourceforge.net >>> Subject: Re: [Emc-users] Lathe conversion with Mesa 5i25 / 7i76 >>> >>> http://wpnet.us/Harrison2.ini >>> http://wpnet.us/Harrison2.hal >>> >> >> The problem I see is the the mpg is connected to the spindle encoder on P2 >> (channel 1) not the mpg encoder on the 7i76 field I/O >> >> >> >> Peter Wallace >> Mesa Electronics >> >> (\__/) >> (='.'=) This is Bunny. Copy and paste bunny into your >> (")_(") signature to help him gain world domination. >> >> >> ------------------------------------------------------------------------------ >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> >> >> ------------------------------------------------------------------------------ >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > > > ------------------------------------------------------------------------------ > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > > ------------------------------------------------------------------------------ > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your (")_(") signature to help him gain world domination. ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users