Ah you still need the loopback interface (the lo interface) you just add 
ontop of the existing config.

The old 3Com Tornado/Boomerang cards isnt always supported out of the 
box actually.
But you can try to change the eth0 to eth1 and see if it sits on a 
different device.

Otherwise i would suspect you need to compile a driver. =)

// Andreas

John Thornton skrev den 2015-04-08 13:42:
> I commented out the original lines and added the second then rebooted
> and no network.
>
> lspci reports: Ethernet Controller 3Com Corporation 3c905C-TX/TX-M
> [Tornado] (rev78)
>
> JT
>
> On 4/8/2015 6:31 AM, Andreas Pettersson wrote:
>> So you dont have a a eth0 at all. then you need to add something like this.
>>
>> allow-hotplug eth0
>> iface eth0 inet static
>> address 192.168.1.150
>> netmask 255.255.255.0
>> broadcast 192.168.1.255
>> gateway 192.168.1.1
>>
>> OR!!
>>
>> allow-hotplug eth0
>> iface eth0 inet dhcp
>>
>> depending on your network of course if you have a router with dhcp/dns
>> you use the second one if not you need to staticly configure.
>>
>> // Andreas
>>
>>
>> John Thornton skrev den 2015-04-08 13:26:
>>> etc/network/interfaces contains two lines:
>>> auto lo
>>> iface lo inet loopback
>>>
>>> JT
>>>
>>> On 4/8/2015 6:17 AM, Andreas Pettersson wrote:
>>>> You would prob. need to activate the card in the config.
>>>> You will find the config file under /etc/network/interfaces
>>>>
>>>> Prob. is the pci card on eth1 instead of eth0 - even if its deactivated
>>>> in the bios.
>>>> it usually "adresses" it self, just not useable.
>>>>
>>>> // A
>>>>
>>>> John Thornton skrev den 2015-04-08 13:12:
>>>>> I have a Debian Wheezy install on a computer down here in the Beer Cave
>>>>> and the other day the power blinked and I lost network connectivity on
>>>>> that computer. After some fumbling around I see that I had a red light
>>>>> on the router for that line instead of a green one. So I put a network
>>>>> card in the PCI slot and plugged that in. Now I have a green light on
>>>>> the router. I went to the bios and turned off the Ethernet on the
>>>>> motherboard. I still don't have a connection to the LAN from that
>>>>> computer. Any clues as to what I need to do?
>>>>>
>>>>> Thanks
>>>>> JT
>>>>>
>>>>> ------------------------------------------------------------------------------
>>>>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
>>>>> Develop your own process in accordance with the BPMN 2 standard
>>>>> Learn Process modeling best practices with Bonita BPM through live 
>>>>> exercises
>>>>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- 
>>>>> event?utm_
>>>>> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
>>>>> _______________________________________________
>>>>> Emc-users mailing list
>>>>> Emc-users@lists.sourceforge.net
>>>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>>> ------------------------------------------------------------------------------
>>>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
>>>> Develop your own process in accordance with the BPMN 2 standard
>>>> Learn Process modeling best practices with Bonita BPM through live 
>>>> exercises
>>>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
>>>> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
>>>> _______________________________________________
>>>> Emc-users mailing list
>>>> Emc-users@lists.sourceforge.net
>>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>> ------------------------------------------------------------------------------
>>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
>>> Develop your own process in accordance with the BPMN 2 standard
>>> Learn Process modeling best practices with Bonita BPM through live exercises
>>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
>>> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
>>> _______________________________________________
>>> Emc-users mailing list
>>> Emc-users@lists.sourceforge.net
>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>> ------------------------------------------------------------------------------
>> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
>> Develop your own process in accordance with the BPMN 2 standard
>> Learn Process modeling best practices with Bonita BPM through live exercises
>> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
>> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
>> _______________________________________________
>> Emc-users mailing list
>> Emc-users@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/emc-users
>
> ------------------------------------------------------------------------------
> BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
> Develop your own process in accordance with the BPMN 2 standard
> Learn Process modeling best practices with Bonita BPM through live exercises
> http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
> source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users


------------------------------------------------------------------------------
BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT
Develop your own process in accordance with the BPMN 2 standard
Learn Process modeling best practices with Bonita BPM through live exercises
http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_
source=Sourceforge_BPM_Camp_5_6_15&utm_medium=email&utm_campaign=VA_SF
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to