On Friday 27 May 2016 23:30:23 [email protected] wrote: And you are top podsting, making it hard to follow the conversation. > OK the interfaces file is: > # The loopback network interface > auto lo > iface lo inet loopback > auto eth1 > iface eth1 inet static > address 10.10.10.1 > > BTW that dmesg gave that from grepping "eth" alone. There is no eth1 > there, only eth0. > > So I changed "eth1" to "eth0" in interfaces and "sudo service > networking restart". > > Now I asked mesaflash and got: > ETH device 7I92 at ip=10.10.10.10 > Now I am confused, and I don't think the 10.10.10.10 address is coming from eth0, but from the mesanet cards, and I am not familiar with the ethernet interfaces the mesa cards can expose, so I believe I'll bow out and ask Peter C. Wallace to bail us out as he knows this stuff much much better than I.
> So, GREAT, ran LinuxCNC, but got the same following error upon axis > motion. Is the axis moving? > > Rebooted. LinuxCNC still gives the same following error. > > Now dmesg has: > [ 1.837260] tg3 0000:03:08.0: eth0: Tigon3 [partno(BCM95788) rev > 3003] (PCI:33MHz:32-bit) MAC address 00:16:17:ad:3f:ea [ 1.837266] > tg3 0000:03:08.0: eth0: attached PHY is 5705 (10/100/1000Base-T > Ethernet) (WireSpeed[0], EEE[0]) [ 1.837271] tg3 0000:03:08.0: > eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ > 1.837275] tg3 0000:03:08.0: eth0: dma_rwctrl[763f0000] > dma_mask[32-bit] [ 12.808639] ADDRCONF(NETDEV_UP): eth0: link is not > ready > Then something is amiss in the interfaces file. Which is a different path than the mesa cards are showing. That is not thru the eth0 interface at all. > But again, mesaflash says it's there at 10.10.10.10. And if you try > to start LinuxCNC without the 7i92 powered up, it won't let you start > LinuxCNC, not wait to move an axis. > > Danny > > ---- [email protected] wrote: > > Alrighty! > > > > OK, found and renamed that .rules to a .rules.bak file and rebooted. > > > > Can't see the 7i92 now. Mesaflash --device 7i92 --addr 10.10.10.10 > > gives "not found". > > > > dmesg has no "ifname" in it at all. > > > > It does have: > > [ 1.820851] tg3 0000:03:08.0: eth0: Tigon3 [partno(BCM95788) rev > > 3003] (PCI:33MHz:32-bit) MAC address 00:16:17:ad:3f:ea [ > > 1.820858] tg3 0000:03:08.0: eth0: attached PHY is 5705 > > (10/100/1000Base-T Ethernet) (WireSpeed[0], EEE[0]) [ 1.820862] > > tg3 0000:03:08.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] > > TSOcap[1] [ 1.820866] tg3 0000:03:08.0: eth0: > > dma_rwctrl[763f0000] dma_mask[32-bit] > > > > Danny > > > > ---- Gene Heskett <[email protected]> wrote: > > > On Friday 27 May 2016 12:54:22 [email protected] wrote: > > > > > > I've sent this message 3 times now. What black hole is gobbling > > > it up? > > > > > > > It's a direct dd copy of the drive. If that wasn't complete, a > > > > lot more would be broken. > > > > > > > > I would not dismantle the (mostly) working system like that. > > > > There's a risk of something getting stored wrong on the working > > > > drive while it's on the new machine, and I don't see anything to > > > > prove by moving it. > > > > > > > > 99.9% sure it's just something different about the ethernet > > > > driver on the new motherboard. Something small. No idea how to > > > > fix it, though. > > > > > > See my reply to Peter, delete > > > /etc/udev/rules.d/70-persistent-net.rules and reboot. It will be > > > rebuilt to match the ethernet hardware in finds as it reboots, and > > > networking will likely be restored. > > > > > > If not, delete it again, grep ' ifname ' /var/log/dmesg to see > > > what it did call it, you should get something that resembles this: > > > > > > gene@coyote:~$ grep ' ifname ' /var/log/dmesg > > > [ 1.401462] forcedeth 0000:00:08.0: ifname eth0, PHY OUI 0x5043 > > > @ 1, addr 00:1f:c6:62:fc:bb > > > [ 1.929064] forcedeth 0000:00:09.0: ifname eth1, PHY OUI 0x5043 > > > @ 1, addr 00:1f:c6:63:07:97 > > > (word wrapped, darn it, what you want is the string after the > > > first ifname. in this example eth0) > > > > > > then use an editor as root to look at the > > > /etc/networking/interfaces file, and rename the stanza for eth0 to > > > whatever the system found and named it to in the /var/log/dmesg > > > file. > > > > > > You should at that point be able to do a "sudu service restart > > > networking" and have the ability to "ping -C2 yahoo.com" and get a > > > 2 normal ping responses from yahoo.com which indicates that > > > networking is now working. > > > > > > > It is an AMD64 though, and the installation was an i686. > > > > > > A non-issue AFAIK. > > > > > > > Danny > > > > > > > > ---- "Peter C. Wallace" <[email protected]> wrote: > > > > > On Fri, 27 May 2016, Danny Miller wrote: > > > > > > Date: Fri, 27 May 2016 00:11:08 -0500 > > > > > > From: Danny Miller <[email protected]> > > > > > > Reply-To: "Enhanced Machine Controller (EMC)" > > > > > > <[email protected]> > > > > > > To: [email protected] > > > > > > Subject: Re: [Emc-users] Copying an installation > > > > > > > > > > > > I do recall we went through much more than expected just > > > > > > getting all that installed. And I don't have a complete > > > > > > list of all that was done. > > > > > > > > > > > > I did poke around again on this machine. > > > > > > > > > > > > Mesaflash says the card's there at 10.10.10.10. > > > > > > > > > > > > After launching LinuxCNC, the VFD does respond to commands > > > > > > just fine. > > > > > > > > > > > > I experimented with the FERROR value- it'll allow the > > > > > > coordinates to change significantly before throwing an > > > > > > error, but the axes will never move regardless. The 7i92 > > > > > > won't put out steps at all. I don't have any enable line on > > > > > > it. > > > > > > > > > > > > Danny > > > > > > > > > > Did you try swapping hard drives as someone suggested, in case > > > > > something was forgotten when moving? > > > > > > > > > > (when linux using generic kernels its much easier to just swap > > > > > hard drives than moving a setup to a new machine) > > > > > > > > > > > On 5/22/2016 6:27 PM, andy pugh wrote: > > > > > >> On 22 May 2016 at 19:51, Danny Miller > > > > > >> <[email protected]> > > > > > > wrote: > > > > > >>> Any advice, folks? I've gotta move off that Dell machine > > > > > >>> ASAP and really want to avoid a whole reinstall. > > > > > >> > > > > > >> I would suggest a complete reinstall of the OS and > > > > > >> LinuxCNC, but keep the same config files. The LinuxCNC > > > > > >> config files should be entirely portable. > > > > > > > > > > > > ------------------------------------------------------------ > > > > > >------ ------------ What NetFlow Analyzer can do for you? > > > > > > Monitors network bandwidth and traffic patterns at an > > > > > > interface-level. Reveals which users, apps, and protocols > > > > > > are consuming the most bandwidth. Provides multi-vendor > > > > > > support for NetFlow, J-Flow, sFlow and other flows. Make > > > > > > informed decisions using capacity planning reports. > > > > > > https://ad.doubleclick.net/ddm/clk/305295220;132659582;e > > > > > > _______________________________________________ > > > > > > Emc-users mailing list > > > > > > [email protected] > > > > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > > > Peter Wallace > > > > > Mesa Electronics > > > > > > > > > > (\__/) > > > > > (='.'=) This is Bunny. Copy and paste bunny into your > > > > > (")_(") signature to help him gain world domination. > > > > > > > > > > > > > > > -------------------------------------------------------------- > > > > >------ ---------- What NetFlow Analyzer can do for you? > > > > > Monitors network bandwidth and traffic patterns at an > > > > > interface-level. Reveals which users, apps, and protocols are > > > > > consuming the most bandwidth. Provides multi-vendor support > > > > > for NetFlow, J-Flow, sFlow and other flows. Make informed > > > > > decisions using capacity planning reports. > > > > > https://ad.doubleclick.net/ddm/clk/305295220;132659582;e > > > > > _______________________________________________ > > > > > Emc-users mailing list > > > > > [email protected] > > > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > > > ---------------------------------------------------------------- > > > >------ -------- What NetFlow Analyzer can do for you? Monitors > > > > network bandwidth and traffic patterns at an interface-level. > > > > Reveals which users, apps, and protocols are consuming the most > > > > bandwidth. Provides multi-vendor support for NetFlow, J-Flow, > > > > sFlow and other flows. Make informed decisions using capacity > > > > planning reports. > > > > https://ad.doubleclick.net/ddm/clk/305295220;132659582;e > > > > _______________________________________________ > > > > Emc-users mailing list > > > > [email protected] > > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > Cheers, Gene Heskett > > > -- > > > "There are four boxes to be used in defense of liberty: > > > soap, ballot, jury, and ammo. Please use in that order." > > > -Ed Howdershelt (Author) > > > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > > > > ------------------------------------------------------------------ > > >------------ What NetFlow Analyzer can do for you? Monitors network > > > bandwidth and traffic patterns at an interface-level. Reveals > > > which users, apps, and protocols are consuming the most bandwidth. > > > Provides multi-vendor support for NetFlow, J-Flow, sFlow and other > > > flows. Make informed decisions using capacity planning reports. > > > https://ad.doubleclick.net/ddm/clk/305295220;132659582;e > > > _______________________________________________ > > > Emc-users mailing list > > > [email protected] > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > -------------------------------------------------------------------- > >---------- What NetFlow Analyzer can do for you? Monitors network > > bandwidth and traffic patterns at an interface-level. Reveals which > > users, apps, and protocols are consuming the most bandwidth. > > Provides multi-vendor support for NetFlow, J-Flow, sFlow and other > > flows. Make informed decisions using capacity planning reports. > > https://ad.doubleclick.net/ddm/clk/305295220;132659582;e > > _______________________________________________ > > Emc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/emc-users > > ---------------------------------------------------------------------- >-------- What NetFlow Analyzer can do for you? Monitors network > bandwidth and traffic patterns at an interface-level. Reveals which > users, apps, and protocols are consuming the most bandwidth. Provides > multi-vendor support for NetFlow, J-Flow, sFlow and other flows. Make > informed decisions using capacity planning reports. > https://ad.doubleclick.net/ddm/clk/305295220;132659582;e > _______________________________________________ > Emc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ What NetFlow Analyzer can do for you? Monitors network bandwidth and traffic patterns at an interface-level. Reveals which users, apps, and protocols are consuming the most bandwidth. Provides multi-vendor support for NetFlow, J-Flow, sFlow and other flows. Make informed decisions using capacity planning reports. https://ad.doubleclick.net/ddm/clk/305295220;132659582;e _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
